Skip to content
Website
🧱 CFC 232Lockout/tagout, dead working and arc flash riskChapter 1 of 10 in the section

The five safety rules: isolate before touching, in the right order

This chapter details the electrical lock-out procedure according to Suva guidelines. You will learn to lock out low-voltage installations methodically before any work on bare conductors. You will master the unchangeable sequence of the five safety rules, the rigorous use of the voltage detector and the fitting of physical locking devices on the building's distribution cabinets.

Key takeaways

  • The five safety rules must be applied in a strict chronological order before any physical handling.
  • All-pole disconnection isolates the work from every potential main or backup power source on site.
  • The personal padlock and the warning sign prevent any unintended re-energising by an uninformed third party.
  • Verification of absence of voltage is carried out with a two-pole tester, checked immediately before and after the operation.

The unchangeable sequence of the five safety rules according to Suva

On construction sites involving high-current installations, working with the power off is the fundamental principle imposed by the Suva guidelines and the OIBT. Any accidental contact with a live part exposes the electrician to fatal electric shock and severe burns caused by a short-circuit arc. Under art. 82 LAA, the employer must take all measures to prevent occupational accidents and diseases that experience has shown to be necessary, that are feasible given the state of the art and that are appropriate to the given conditions; workers assist the employer by rigorously applying the protection protocols. Electrical lock-out allows no compromise: the five safety rules form a continuous chain of technical actions in which each link directly determines the validity of the next. Departing from this sequence or omitting a step turns a routine connection job into an immediate danger for the team.

  1. Switch off and fully disconnect the installationOpen all all-pole disconnecting devices (main switches, service circuit breakers or fused disconnectors) to separate the work area from all mains, inverter or generator voltage sources.
  2. Secure against any unintended re-energisingMechanically lock the operating devices in the open position using a personal lock-out padlock or locking pins, then attach a visible sign strictly prohibiting any operation by a third party.
  3. Verify that there is absolutely no voltageCheck each live conductor against earth, against the neutral conductor and between successive phases at the very place of work, using exclusively a two-pole voltage detector that has been tested beforehand.
  4. Earth and short-circuitConnect the isolated conductors to the main earthing collector and then short-circuit them together, a systematic step in high voltage and strongly required in low voltage where there are risks of induction or back-feed.
  5. Protect and delimit the area against adjacent bare partsFit insulating profiles or sheets over adjacent busbars or terminals that remain live, then clearly mark out the perimeter in which the fitter will work.

Mechanical locking, signage and verification of absence of voltage

Physical locking and signage form the organisational lock of the construction site. A circuit breaker that is simply switched off is in no case a valid lock-out. Art. 3 OPA specifies that the employer must take the protective provisions and measures that meet the requirements of the ordinance, the other applicable occupational safety provisions and the recognised rules of safety engineering and occupational medicine. The electrician applies this principle by fitting a multiple hasp and an individual padlock, the only key to which stays in their own pocket. Lockable modular shutters and caps over handles prevent any re-setting operation. This mechanical blocking must always be accompanied by a standardised warning sign stating the name of the person responsible, the date, the nature of the work and the ban on switching on. This signage informs all the trades working in the technical rooms that the electrical panel has been deliberately switched off.

Verification of absence of voltage (VAV) requires strict operating discipline known as the three-step rule. The fitter must never use a standard multimeter or a neon-lamp screwdriver tester, which are regular sources of accidents through wrong range selection or random body resistance. Only an approved two-pole voltage detector guarantees a reliable result. The device is tested on a source of proven voltage or with its built-in self-test, then applied to all poles of the work area (phases, neutral and protective earth), before being immediately tested again on the known source to confirm that it worked without interruption.

Measurement protocol and confirmation of absence of voltage in low voltage
Check stepMethodCompliance criterion
Upstream self-test of the detectorApply the probe tips to a known live socket or activate the internal test functionContinuous audible signal and voltage-present indicator lights come on
Multi-pole measurementProbe in succession phase-phase, phase-neutral, phase-earth and neutral-earth on the disconnected terminalsZero volts displayed, no audible or visual signal at all on each pole
Downstream self-test of the detectorRepeat the test on the same known reference source immediately after the measurementConfirmation that the two-pole tester remained fully functional during probing

Earthing, short-circuiting and protection against adjacent parts: rules 4 and 5

Applying the first three steps guarantees that the circuit is interrupted and that the de-energised state is verified at the point of isolation. However, in complex high-current distribution installations, the risk of an accidental return of voltage or of induction remains real. The fourth rule therefore requires the live conductors to be earthed and short-circuited at the place of work or as close to it as possible. This action protects the electrician against unexpected re-energising caused by independent sources, unrecorded downstream loops or backup generators switched on without the team's knowledge.

In low voltage, earthing and short-circuiting is required whenever there is a risk of induced voltage, for example near overhead lines, parallel large-cross-section cables under load, or during work on low-voltage main switchboards where re-energising remains possible. The connection order allows no deviation: the earthing cable is first firmly connected to the main earth terminal or to the protective collector of the switchboard, then the short-circuit clamps are fixed in succession to each of the phase conductors and to the neutral. This sequence ensures that any residual charge discharges directly to earth before the potentials between phases are equalised.

Implementing rules 4 and 5 in cabinets and distribution boards
Safety stepRequired deviceProcedure on the construction siteRisk eliminated
Rule 4: Earth and short-circuitPortable earthing and short-circuiting device rated for the prospective short-circuit currentFirst fix the braid to the PE collector, then connect the clamps to the phase busbars and the neutral conductor.Induced voltages, capacitive coupling, unintended start-up of downstream inverters or generators.
Rule 5: Screening of bare partsRigid insulating profiles, elastomer insulating sheets, clip-on caps suitable for low voltageFit the screens over adjacent feeders left live, working from the bottom upwards along the busbar set.Involuntary brushing, a hand tool slipping, indirect contact with adjacent bare parts.
Rule 5: Delimiting the areaRed and white plastic warning chains, Suva warning signsFence off the work perimeter and visibly mark the cells or cabinets that remain live.The worker mistaking the bay when moving about or resuming work after an interruption.

The fifth rule consists of covering adjacent bare parts that have remained live and formally delimiting the work area. In cramped technical rooms and distribution cells, busbars or incoming terminals often remain live to maintain the continuity of other circuits in the building. The electrician must isolate these elements using suitable protectors, insulating sheets held by non-conductive clamps or rigid interlocking profiles. The separating screen must be strong enough not to flex under the accidental pressure of a hand or a tool.

Site organisation, Suva guidelines and the reverse procedure for lifting the lock-out

The effectiveness of the five safety rules rests on rigorous work organisation and an explicit allocation of responsibilities. In accordance with the Suva guidelines on the dangers of electricity, operating and modification work on electrical installations must be methodically prepared. The employer takes the prevention measures suited to the task under art. 82 LAA, while fitters and team leaders are required to assist the company by strictly applying the prescribed safety measures.

On large construction sites, lock-out involves the formal appointment of a lock-out officer and a work officer. The lock-out officer carries out, or has carried out, the five actions, ensures that there is absolutely no voltage, fits the lock-out padlocks and hands the signed lock-out certificate to the team leader. As long as this document has not been initialled, the order to touch cannot be given to the workers. The Ordinance on the Prevention of Accidents and Occupational Diseases reminds us in art. 3 OPA that the employer puts in place protective measures that meet the recognised rules of technology in order to prevent damage to health.

  1. 1. Pulling back from the site and evacuating personnelGather all the workers, make sure that nobody is still in contact with the installation, have the tools put away and strictly forbid any new access to the area.
  2. 2. Removing the delimitations and the adjacent protectionsRemove the marking chains and temporary signs, then carefully remove the insulating sheets, caps and profiles protecting the adjacent bare parts.
  3. 3. Removing the earthing and short-circuitYou must disconnect the clamps fixed on the live conductors (phases and neutral) before unscrewing the braid connected to the earth collector.
  4. 4. Removing the locks and signageEach worker unlocks their personal padlock on the lock-out hasp. The lock-out officer removes the prohibition signs and the circuit-breaker locks.
  5. 5. Re-switching on and re-energisingClose the disconnecting devices in the order of the distribution diagram, check visually that the board behaves correctly and check that the correct service voltages are present.

Lock-out anomalies and emergency conduct on the construction site

Safety on an electrical installation rests on absolute rigour: if any one of the five lock-out steps cannot be completed or reveals an abnormal situation, work does not start. Under art. 82 LAA, the employer takes all necessary measures that the state of the art makes it possible to apply in order to prevent accidents, and the workers assist in this effort. In the field, applying the Suva guidelines requires an immediate reaction to the slightest unforeseen event.

  1. Residual voltage detected by the detectorIf the voltage detector indicates a potential, even a low one, stop the operation. Do not touch any live conductor. The anomaly often points to back-feed from downstream, capacitive coupling on long parallel cables, a return via the neutral conductor or the presence of an independent source that has not been identified, such as a photovoltaic inverter or a backup generator. Inform the operations manager or the team leader so that the origin of the feed can be traced before any further work.
  2. Mechanical locking impossibleWhen a disconnecting device has no lock-out eyelet or locking accessory suited to the modular circuit breaker, simply displaying a prohibition sign is not enough. Physical disconnection must be guaranteed. Remove the upstream fuses if the device is withdrawable, apply a lock to the cover plate or lock the technical room or the distribution cabinet concerned with a key, keeping the key on you.
  3. Impossible to delimit the live surroundingsIf live bare parts remain within hand's reach inside the enclosure and no rigid insulating protector or insulating sheet can be fixed securely, the construction site must be stopped. In accordance with art. 3 OPA, the employer implements the protective measures that meet the recognised rules of technology; the disconnection perimeter must then be widened to the main circuit breaker upstream.
  4. Procedure in the event of an accident or arcingIn the event of an electric arc or electric shock, never touch the victim directly while they are still in contact with the source. Cut the power in an emergency using the emergency stop button or the nearest main switch. If immediate disconnection is impossible, free the person using a certified insulating pole. Immediately call the emergency medical services on 144, secure the area to avoid any further accident, give first aid and inform site management.

Frequently asked questions

What should I do if my detector shows zero volts but the self-check test fails?

You must treat the installation as live. A two-pole voltage detector must be proved on a known live source immediately before and immediately after the measurement, or via its built-in self-test button depending on the model. If the tester is faulty, replace it with a compliant device and repeat the whole of the third rule before authorising any manual contact.

Can I be satisfied with simply withdrawing a circuit breaker without fitting a padlock?

No. Withdrawal creates a visible isolating distance, but does not protect against accidental re-closing by a third party working in the same cabinet. The Suva guideline and the recognised rules require the mechanism to be blocked in the withdrawn position with a padlocked device, or a locked shutter to be fitted that prevents the device from being inserted as long as the area remains locked out.

Is earthing and short-circuiting required in indoor low voltage?

In final low-voltage circuits inside a building, rule number 4 applies primarily where there are large-cross-section cables, risks of back-feed by injection from upstream or downstream, or overhead lines. On a standard sub-distribution board, earthing is mandatory if induced voltages may remain or if particular operating instructions formally require it.

Who holds the key to the lock-out padlock for the duration of the work?

The key remains in the exclusive custody of the person doing the work or of the designated lock-out officer. If several fitters work on the same installation, each fits their own individual padlock on a multiple lock-out hasp. No third party may be able to remove the locking device as long as a worker is in the work area.

Texts and standards cited

  • LAA art. 82general prevention rules: the employer must take, to prevent occupational accidents and diseases, all measures that experience has shown to be necessary, that are feasible given the state of the art and that are appropriate to the given conditions; the workers assist the employer (in particular, they use personal protective equipment).
  • OPA art. 3protective measures and installations: the employer must take the protective provisions and measures that meet the requirements of the ordinance, the other applicable occupational safety provisions and the recognised rules of safety engineering and occupational medicine.

In the same section