Key takeaways
- For any building constructed before 1990, the asbestos survey must be consulted before drilling.
- Fibre-cement conduits, insulation boards and old mastics are frequent suspect materials.
- Art. 32 OTConst requires work to be interrupted when a hazardous substance is unexpectedly discovered.
- The removal or remediation of friable materials is entrusted exclusively to a recognised company.
Identifying asbestos-containing materials in old electrical routes
On construction sites converting buildings erected before the 1990 ban, the routes of risers and power-cable passages commonly cross products containing asbestos. In fire-rated service ducts, electricians frequently encounter lightweight partitions, ventilation ducts or cable passages made of fibre cement, as well as thermal-protection wall panels located behind old main or secondary distribution boards.
| Location in the installation | Material or product encountered | Risk of fibre release |
|---|---|---|
| Backboard of old distribution boards | Cardboard or compressed fibre-cement panels | High when drilling or fixing |
| Floor penetrations and service ducts | Rigid asbestos-cement conduits | Low when undisturbed, critical when sawing |
| Fire-rated wall penetrations | Textile packing and intumescent mastics | Medium to high when pulling cables |
| Technical false ceilings | Lightweight silicate-based insulating panels | Very high when mechanically perforated |
The main danger lies in the friable nature of certain insulating components. While asbestos cement firmly binds the mineral fibres in a compact matrix when intact, low-density acoustic panels or thermal barriers instantly release millions of invisible fibres at the slightest action of a hammer-drill bit or hole-saw blade. These airborne particles remain suspended for a long time in the atmosphere of confined ducts.
Before any power tool is used to run a new cable tray, the team leader requires the building's pollutant survey to be consulted. This document must precisely locate the elements analysed in the work area. If a slab penetration or a service-duct lining is not within the area investigated by the report, any doubt requires formal verification before any clamps or metal brackets are fixed.
Applying the stop-work procedure and organising the resumption of work
In accordance with art. 32 OTConst, if such a substance is unexpectedly found, work must be interrupted and the client or their representative informed. The electrician does not improvise any clearing, partial demolition or dust removal with a standard workshop vacuum cleaner, as this equipment discharges microscopic fibres directly into the ambient air through its exhaust filter.
- Immediate cessation of the mechanical actionStop the rotary or percussion tool at once, set the machine down gently without blowing on the area, and switch off local ventilation if there is any.
- Closing off and marking out the areaClose the door of the duct or room, put up barrier tape and display a no-entry sign to protect the other trades.
- Written notification to the person in chargeInform the foreman or the company's safety officer, then record the stoppage in writing to the site management and the client.
- Sampling and analytical confirmationHave a certified surveyor take a material sample under a strict protocol and obtain a result from an accredited laboratory.
Remediating or drilling through an element containing toxic mineral fibres never falls within the competence of the electrician. Art. 82 OTConst states that work releasing a significant quantity of asbestos fibres hazardous to health into the air may only be carried out by asbestos-removal companies recognised by the SUVA.
Once the specialist intervention is complete and the containment has been lifted, the electrician installs conduits and cable trays on a sound substrate. When installing new risers under fire protection, the penetrations are then reinstated with recent approved sealing systems, free of harmful fibres, ensuring the smoke-tightness and thermal resistance required.
Pre-work survey and analysis of routes before drilling
On renovation construction sites for buildings erected before 1990, the electrical foreman cannot plan any cable route or drilling without consulting the pre-work survey report. Vertical service ducts, slab penetrations, removable or suspended false ceilings and fire-stopping seals concentrate major risks of exposure to toxic dust. The initial assessment documents the location of asbestos-containing materials, their state of deterioration and the level of accessibility for the finishing-work trades.
Under art. 32 OTConst, where the presence of asbestos is suspected, the employer informs the workers of the survey results, and if a hazardous substance is unexpectedly discovered, work must be interrupted and the client or their representative informed. The installation team reviews the identification plans at the preparatory meeting to locate sensitive areas before the site installations are set up.
| Building element | Form of asbestos | Risk during work | Site instruction |
|---|---|---|---|
| Riser ducts and sleeves | Rigid asbestos cement | Sawing or core drilling releasing dust | Do not drill or cut the tube |
| Fire-rated board panels in distribution boards | Compressed material or cardboard | Dismantling causing direct crumbling | Keep the casing intact with no mechanical action |
| Plaster or board false ceilings | Insulating panels or filled plaster | Drilling hangers generating a dust cloud | Stop plugging and fixing, and mark out the area |
| Mastics in junction boxes | Bituminous sealing compounds | Scraping or pulling out old conductors | No handling in the cabinets concerned |
Where the initial survey provided by the project management is incomplete, the electrician requires a supplementary investigation targeted at the planned cable passages. Any penetration of a rotary tool into masonry covered with old plaster, or through an uncharacterised technical false ceiling, represents a direct health risk through inhalation of invisible fibres.
Reporting to the client and calling in the recognised company
As soon as a fitter discovers a doubtful, unlisted material — such as a friable greyish conduit or a thermal insulation braid around an old distribution — the workshop instruction is a calm and orderly withdrawal. The fitters put down their machines, close access to the room and put up a warning sign. The site foreman writes a notification to the site management and the client, stating the floor, the room and the element concerned.
Art. 82 OTConst provides that work releasing a significant quantity of asbestos fibres hazardous to health into the air may only be carried out by asbestos-removal companies recognised by the SUVA. The electrician takes no part whatsoever in dismantling contaminated pipework or in removing dust from technical voids. This task falls exclusively to a specialist remediation contractor, working under sealed containment with controlled negative pressure, a decontamination airlock and very-high-efficiency filters.
Electrical work remains suspended until the recognised company has completed the remediation and handed over an air measurement report proving that the fibre concentration has dropped below the limit value set for re-occupation of the premises. On receipt of this clearance certificate issued under the responsibility of the asbestos consultant, the foreman again schedules the installation of cable trays, halogen-free installation conduits and new sub-distribution boards on perfectly sound walls.
Incident management: accidental breakage of an asbestos conduit and safe resumption of work
During core drilling, plugging or fixing of a cable tray, accidental penetration of a fibre-cement pipe or an asbestos-containing fire-rated panel releases highly toxic dust. Faced with this unforeseen situation, the team on site must on no account try to clean up the contaminated area or continue running the conductors. All dry sweeping and the use of a standard site vacuum cleaner are prohibited, because conventional filters release and spread the invisible particles throughout the whole building.
The measure on site is to evacuate the fitters from the room and close the openings to contain the space. Switching off the ventilation systems prevents dust from being carried to the other floors of the building. The team leader closes off access with barrier tape and an explicit no-entry sign. In application of art. 32 OTConst, if such a substance is unexpectedly found, work must be interrupted and the client or their representative informed.
Decontamination of the polluted area requires specialist external intervention. In accordance with art. 82 OTConst, work releasing a significant quantity of asbestos fibres hazardous to health into the air may only be carried out by asbestos-removal companies recognised by the SUVA. These specialists put the premises under negative pressure, collect the debris under containment and fully remediate the affected walls before removing the special waste via authorised channels.
The electrician resumes laying conduits or pulling power conductors only after the clearance air analysis report, ordered by the site management, has been handed over. If the original route passes through a contaminated service duct that has not been remediated, the company adapts its installation plan in consultation with the consultants: bypassing it with surface-mounted rigid conduit, routing through a secondary technical corridor or drilling a new clean penetration. This change is covered by a technical addendum to record the additional costs and justify the schedule delays caused by this interruption.
Frequently asked questions
What should be done if an old electrical conduit looks like fibre cement but is not listed in the survey?
Where the building's pollutant survey makes no explicit mention, the precautionary principle applies. The electrician does not drill, saw or remove the doubtful element. They notify their superiors and the site management without delay to request sampling by a certified surveyor. Work on this area remains on hold until the results of the analysis by an accredited laboratory confirming the absence of toxic mineral fibres have been received.
Can an electrician drill an asbestos conduit using a vacuum cleaner fitted with a HEPA filter?
No, this operation remains prohibited for electrical staff. Direct mechanical drilling of a material containing asbestos generates a massive emission of fine dust. Even when equipped with a respiratory protection mask and a class H absolute-filtration vacuum cleaner, this type of cutting requires specific containment protocols, certified training and a working method reserved for asbestos-removal professionals. The electrician must therefore call in an approved contractor.
Who bears the costs of the work stoppage and decontamination following an unexpected discovery?
The financial burden falls on the client, the owner of the building. Remediation of hidden pollutants and additional surveys are unforeseen conditions attributable to the client. The electrical installation company documents the interruption, quantifies the waiting hours of its fitters and notifies the schedule delays. An addendum to the works contract is drawn up to cover the route adaptations, travel times and the resumption of the installations.
How can new supply cables be pulled into a suspect riser that has not been remediated?
If the riser shows suspect residues or pre-1990 mastics that have not been analysed, cable pulling is suspended. Mechanical friction of pulling rods or conductors against friable walls risks detaching asbestos fibres. In agreement with the consultant, two options exist: have the duct remediated beforehand by a specialist company, or re-plan the route by installing new surface-mounted conduits outside the contaminated area.
Texts and standards cited
- OTConst art. 32Substances particularly hazardous to health (asbestos, PCB): interruption of work and information of the client or their representative in the event of an unexpected discovery
- OTConst art. 82Asbestos removal: work releasing a significant quantity of asbestos fibres hazardous to health may only be carried out by companies recognised by the SUVA
