Skip to content
Website
🧱 CFC 232Section 3 of 610 chapters

Measurements, checks and safety report: the execution reference

Intended for installation electricians, lead fitters and site managers, this section details the metrological and regulatory validation of high-voltage installations in accordance with the NIBT and the OIBT. From the initial de-energised verification through to the issue of the safety report and the thermographic inspection of switchboards, you have the complete protocol to ensure the protection of persons, eliminate any fire risk and pass technical acceptance.

  • 10chapters
  • 22 000words
  • 6sections in the training course
  • 60chapters in total

Key values to remember 5

NIBT

1.0 MΩ

Minimum insulation resistance for new circuits up to 500 V

NIBT

500 V

DC test voltage required for low-voltage insulation measurement

NIBT

0.2 A

Minimum DC current required for the PE conductor continuity test

NIBT

0.4 s

Maximum automatic disconnection time in a TN system for a final circuit ≤ 63 A

NIBT

300 ms

Maximum permissible tripping time for a standard RCD at its rated current

Technical scope of the checks and boundaries of intervention

The final check carried out by the installation electrician is the technical act that engages his civil and criminal liability before any handover of the works to the owner. Under the requirements of the OIBT and the NIBT, no high-voltage installation may be permanently energised without having successfully undergone the full sequence of visual inspections, continuity tests and insulation measurements. This methodical process aims to exclude any danger of electric shock, burns or fire resulting from a short circuit or an insulation fault.

This scope covers exclusively low-voltage distribution in buildings, from the main overcurrent protective device to the terminals of fixed consumers and socket outlets. Strictly excluded from this section are the communication, fibre-optic and home-automation control networks falling under CFC 238, as well as the fluid connection and terminal control of heat pumps (CFC 241) or air-handling units (CFC 244). Verification of the mechanical strength of supporting walls falls under CFC 201.

Demarcation of technical responsibilities for the acceptance of installations
Technical fieldResponsible tradeExpected testing serviceMandatory legal document
Power and lighting distributionInstallation electrician (CFC 232)Complete NIBT measurements and visual inspectionSafety report and measurement record
Structured cabling and telecomsTelematics technician (CFC 238)Reflectometry and copper/fibre certificationNetwork measurement report
Heat pump and motor supplyInstallation electrician (CFC 232)PE continuity and RCD trippingFinal circuit measurement sheet
HVAC components and sensorsHeating installer (CFC 241)Control loops and heating testsTechnical commissioning record

Methodical organisation of the checks and chapter sequence

The testing procedure follows an unchangeable chronology dictated by physics and by the safety of the person taking the measurements. Every test must begin de-energised, with the visual examinations, verification of the continuity of the protective conductors and measurement of the insulation resistance. The order of the chapters below faithfully reproduces the steps required in the field, allowing the final file intended for the client and the network operator to be prepared methodically.

  1. De-energised phase: continuity and insulationFirst measure the continuity of the equipotential bonding and PE conductors with a minimum DC voltage of 4 V and a current of at least 0.2 A. Then carry out the insulation test at 500 V DC, after first isolating sensitive electronic consumers and surge arresters.
  2. Energised phase: loops and RCDsApply the operating voltage to verify the L-PE and L-N fault loop impedance, validate the prospective short-circuit current allowing automatic disconnection within the NIBT time, then measure the actual tripping time and current of the RCDs.
  3. Load phase: heating and balancingInspect the connections in the cabinet by infrared thermography under real load current to detect any abnormal overheating before the covers are finally closed.
  4. Documentation phase: administrative closureCompile the measured values in the test record, draw up the safety report, rectify any defects and appoint the independent inspection body where the OIBT periodicity requires it.

📘 Chapters in this section 10

Measurements, inspections and safety report

Insulation measurement: test voltage, expected value and equipment to disconnect

Master the method of applying the test voltage without destroying the building's electronic boards.

Measurements, inspections and safety report

Fault loop impedance: what the measurement proves and how to read it

Interpret your loop impedance measurements immediately to validate the magnetic tripping of the circuit breakers.

Measurements, inspections and safety report

Testing an RCD: tripping current, time, and why the test button is not enough

Find out why the test button on the front panel absolutely does not guarantee the safety of users.

Measurements, inspections and safety report

Continuity of the protective conductor: the measurement you never skip

Make the continuity measurement safe in order to uncover faulty earth connections before energisation.

Measurements, inspections and safety report

Before first energisation: the order of checks and measurements

Apply the mandatory chronological order of checks to avoid any electric arc on switching on.

Measurements, inspections and safety report

Safety report: who prepares it, what it contains and who receives it

Draw up a flawless safety report that validates your installation with the energy distributors.

Measurements, inspections and safety report

Independent inspection: when it is required and how to prepare for it

Anticipate the visit of the independent inspector to obtain a certificate of conformity without reservations.

Measurements, inspections and safety report

Defects found at inspection: hierarchy, correction deadline and immediate disconnection

Prioritise the handling of the anomalies found to avoid a disconnection order from the network operator.

Measurements, inspections and safety report

Thermography of a switchboard: detecting overheating before it causes a fire

Use infrared imaging under load to neutralise the loose connections that cause fires.

Measurements, inspections and safety report

File handed to the client: diagrams, report, instructions and labelling

Structure the final works file to close out the statutory warranties without dispute from the client.