Key takeaways
- The NIBT requires a 30 mA RCD on socket-outlets up to 32 A.
- Rooms with a bath or shower require this disconnection on all of their circuits.
- Disconnection in less than 300 milliseconds prevents fatal ventricular fibrillation in the user.
- Distribution over several RCD groups ensures continuity of service of the final circuits.
Mandatory circuits under the NIBT and voluntary extension to fixed equipment
The low-voltage installations standard (NIBT) prescribes the use of residual current devices (RCDs) with a rated current of no more than 30 mA as additional protection against direct and indirect contact. This requirement targets above all the final circuits supplying socket-outlets intended for lay users. Every general-use socket-outlet up to 32 A must be protected by a 30 mA tripping threshold. Outdoor socket-outlets, circuits supplying portable appliances on construction sites and temporary installations are subject to this same strict rule of automatic disconnection.
| Location or equipment | NIBT 30 mA requirement | Usual device type | Professional justification |
|---|---|---|---|
| Indoor socket-outlets ≤ 32 A | Yes | Type A | Risk of wear of flexible cords |
| Outdoor socket-outlets | Yes | Type A or F | Moisture and handling on conductive ground |
| Bathroom (zones 1 and 2) | Yes (all circuits) | Type A | Body resistance collapsed by water |
| Fixed lighting in a dry area | No (recommended) | Type A | Safety when replacing light sources |
| Vehicle charging points | Yes | Type B or A-EV | Detection of leakage currents with a DC component |
In rooms containing a bath or shower, the NIBT extends the 30 mA RCD requirement to all circuits passing through or serving the classified zones, including fixed lighting, ventilation or heating element circuits connected without a socket. Sprayed water drastically lowers the ohmic resistance of human skin, making any enclosure fault immediately lethal under the presumed touch voltage of 230 V.
On site, the electrician-installer formalises these choices in the safety report (RSi) drawn up after the usual final checks. The absence of a 30 mA RCD on a circuit where one is prescribed is a major defect that blocks the handover of the works file to the network operator.
Tripping dynamics and modular architecture to prevent a general trip
The 30 mA threshold corresponds to the physiological limit beyond which current passing through the human thorax risks inducing irreversible ventricular fibrillation. The multifunction measuring instrument used for the periodic inspection injects a test current to validate effective tripping. In the TN system usual in French-speaking Switzerland, the NIBT requires disconnection within a maximum of 300 ms at 1 x IΔn, the residual current circuit breaker generally reacting in the workshop in less than 30 to 40 ms.
- Splitting into RCD groupsNever fit a single 30 mA RCD at the head of the board. Distribute the circuits over at least two to three separate residual current switches supplied by suitable busbar combs.
- Separation of critical zonesSeparate lighting circuits from socket-outlet circuits. The failure of a toaster or a coffee machine must not plunge a staircase or an escape corridor into darkness.
- Assignment of individual residual current circuit breakers (RCBO)Assign individual combined RCBOs to sensitive equipment such as the freezer, the clean-water sump pump or IT circuits.
- Measuring permanent leakage currentsCheck with a milliampere clamp meter that the natural capacitive current of the interference suppression filters does not exceed 10 mA per group, to avoid nuisance tripping.
When assembling a distribution board, the use of two-pole or four-pole vertical connection combs simplifies wiring while keeping complete legibility for later troubleshooting. Horizontal selectivity remains the only way to ensure the protection of persons without degrading the availability of the installation.
Measurement protocols and real thresholds: validating the 30 mA disconnection
Fitting a residual current device (RCD) rated at 30 mA does not by itself guarantee the safety required by the NIBT. The electrician-installer must verify the real effectiveness of the device using a calibrated installation tester, connected directly downstream on the socket-outlets and the terminals of the connected appliances. This is not a simple continuity check but a rigorous simulation of an earth leakage under different current waveforms.
| Test applied | Injected current | Expected tripping time | Purpose of the test |
|---|---|---|---|
| Non-tripping threshold | 0.5 × IΔn (15 mA) | No tripping | Check that there is no nuisance tripping under minimal leakage |
| Nominal safety threshold | 1.0 × IΔn (30 mA) | ≤ 300 ms | Measure the fault clearing time at rated current |
| Direct shock current | 5.0 × IΔn (150 mA) | ≤ 40 ms | Ensure immediate protection in the event of clear direct contact |
| Progressive ramp | from 6 mA to 30 mA | Tripping between 15 mA and 30 mA | Record the actual tripping current of the magnetic toroid |
On a construction site or during a renovation in French-speaking Switzerland, an actual tripping threshold below 18 mA often indicates the presence of pre-existing stray currents on the neutral or saturated capacitive interference filters. The most unfavourable measurement must be documented in the test record prior to drawing up the safety report (RS / RaSi).
Board topology, permanent leakage currents and continuity of operation
To avoid the general trip that plunges a dwelling or a workshop into complete darkness at the slightest anomaly, low-voltage distribution requires a rigorous segregation of circuits. A general 30 mA RCD at the head of the board is a major design error that contravenes the principles of energy availability. The electrician-installer favours horizontal splitting using several separate RCDs or the systematic use of combined residual current circuit breakers (RCBO).
- Isolation of critical circuitsSupply the freezer, the clean-water sump pump or the technical alarm equipment on dedicated RCBOs, immune to nuisance tripping, to preserve their operation in the event of a fault on an ordinary socket-outlet.
- Strict separation of neutral barsAssign an independent neutral bar to each group protected by a four-pole or two-pole RCD. Any accidental neutral bridging between two RCD zones generates a zero-sequence component that trips both devices at the first load demand.
- Predictive calculation of leakage currentsLimit the sum of permanent leakage currents (household appliances, drives, switch-mode power supplies) to a maximum of 10 mA per 30 mA RCD section, in order to retain a sufficient dynamic margin against transients.
- Checking cable lengthsIn commercial distribution systems or craft workshops, check the capacitance per unit length of long lines in conduit which, through natural capacitive effect at 230 V, drain a permanent residual current to earth.
The obligation to ensure the protection of persons must be matched by a requirement of method during work near live parts. Art. 82 LAA requires the employer to take all the preventive measures which experience has shown to be necessary and which the state of the art allows to be applied, and workers are required to use the personal protective equipment made available to them.
Managing nuisance tripping and reworking a non-compliant board
On site, a 30 mA residual current device (RCD) that trips without a genuine insulation fault almost always results from the summation of capacitive leakage currents or a neutral error. The electrician-installer must methodically isolate the circuits rather than replace the device with a higher rating or remove the protection. Fault finding begins with measuring the overall leakage current using a leakage current clamp enclosing all live conductors (phases and neutral).
- Locating the leaking circuitOpen all the distribution circuit breakers downstream of the 30 mA RCD. Reset the RCD, then close the circuits one by one while measuring the residual current with the clamp. The circuit causing an immediate trip or a sudden rise beyond 10 to 15 mA is logged for investigation.
- Checking for neutral mix-upsCheck on the connection bars that no neutral conductor belonging to the group protected by the RCD is connected to the bar of another RCD or to the main busbar. A crossed neutral causes tripping as soon as the associated equipment is put under load.
- Insulation measurement under test voltageDisconnect sensitive equipment and carry out an insulation measurement at 500 V DC between the live conductors connected together and the protective conductor (PE). A value below the NIBT requirements means the damaged connection must be located and repaired.
If the client refuses the compliance work or the essential subdivision of the groups during a renovation, the contractor faces a direct legal risk. Under art. 365 CO, if a circumstance jeopardises the proper or timely execution of the work, the contractor must immediately inform the client. This written notification relieves the installer of technical responsibility while recording the defect in the safety report.
Frequently asked questions
Why does my 30 mA RCD trip as soon as I switch on an oven, with no apparent insulation fault?
Sheathed heating elements absorb ambient moisture when they remain cold for a long time, which temporarily lowers the insulation resistance of the internal mineral insulation. This leakage current to the metal casing connected to PE often exceeds the actual tripping threshold of the RCD (15 to 25 mA). The remedy is to dry out the element or to connect the appliance temporarily under strict supervision during its warm-up to drive off the moisture.
How should I react to an old board without a distributed protective conductor when replacing an RCD?
Fitting a 30 mA RCD on a network in a TN-C system (PEN conductor) is technically impossible without prior separation. The RCD only works if the neutral and the protective conductor are separate. It is imperative to create the neutral and earth separation upstream of the RCD, to establish the changeover to TN-S, and to distribute a PE conductor to the replaced socket-outlets, otherwise the RCD will be inoperative or subject to constant tripping.
What should be done when the cumulative mains filters of a professional kitchen trip the general RCD?
The EMC interference suppression filters of drives, induction hobs and professional ovens each structurally generate 1 to 3 mA of functional leakage current to earth. If eight pieces of equipment share the same 30 mA RCD, the tripping threshold of 20 mA is reached without any failure. The circuits must be split by installing dedicated individual residual current circuit breakers (RCBO), or the loads grouped in subsets of no more than three appliances.
What measured disconnection times are tolerated during the final test of a 30 mA RCD?
According to the NIBT inspection rules, the tripping time at the rated residual current of 30 mA must not exceed 300 milliseconds for a standard instantaneous RCD. During acceptance measurements at half-wave under full rated current, a compliant RCD generally trips between 15 and 35 milliseconds. Any device exceeding 300 milliseconds or not tripping at its rated current must be recorded as defective and replaced immediately.
Texts and standards cited
- CO art. 365materials and ground: the contractor is responsible for the good quality of the materials he supplies; if the materials supplied by the client or the ground designated by him are found to be defective, or if any other circumstance jeopardises the proper or timely execution of the work, he must immediately inform the client, failing which he bears the consequences (para. 3).
