Key takeaways
- The electrical continuity of the protective conductor determines the real effectiveness of all automatic disconnection devices.
- The measurement is always carried out with a minimum current of two hundred milliamperes with automatic polarity reversal.
- Every accessible conductive part must be checked individually, without ever resorting to sampling.
- All measured values must be recorded in writing before the final drafting of the official safety report.
Point-by-point measurement guarantees that the tripping devices will operate effectively
On a power installation, the physical presence of a green-and-yellow conductor in a conduit or a cable tray proves nothing about its actual connection. Without a continuous link to the earth busbar of the distribution board, protective measures against electric shock by automatic disconnection become completely ineffective. In the event of a solid insulation fault in a class I appliance, the metal casing remains at a dangerous voltage without causing the thermal-magnetic circuit breakers to react or the residual current circuit breakers to trip. Checking this protective loop is therefore the absolute technical prerequisite for any final energisation.
- Protective conductor (PE)
- Electrical conductor prescribed by NIBT to provide protection against indirect contact, connecting the metal exposed parts of electrical equipment to the main earthing terminal.
NIBT requires the measurement to be carried out at every point of the installation, and accepts neither a simple visual check nor extrapolation by statistical sampling. To carry out this test, the installation electrician uses an installation tester delivering an open-circuit voltage between 4 and 24 volts DC, with a minimum test current of 200 milliamperes. This calibrated measuring current makes it possible to break through any micro-oxidation layers present on terminals or spring contacts, which a standard low-power battery-operated multimeter would not detect.
- Isolation and preparation of the circuitMake sure there is no voltage at all on the installation and connect the auxiliary reference conductor directly to the earth bar of the relevant distribution board.
- Compensating for test lead resistanceShort-circuit the probe tip of the cable reel and that of the measuring instrument to activate the zero-balancing (offset) function and cancel the inherent resistance of the test leads.
- Methodical terminal-by-terminal probingApply the measuring probe to each earth pin of the socket outlets, to the earth terminals of the lighting strips and to the casings of permanently connected appliances.
The measured value must be consistent with the geometric length of the route and the copper cross-section of the protective conductor. A resistance above 1 ohm on a standard final circuit immediately signals an anomaly: a push-in terminal not properly engaged, a loose screw terminal block, or a wire severed during pulling through conduit bends.
Hunting down overlooked metal exposed parts and recording test results
One of the recurring pitfalls on construction sites is the lack of continuity of so-called extraneous or secondary metal parts. Technical raised-floor structures, modular partition frames, perforated sheet-metal cable trays and the metal frames of distribution cabinets must have flawless equipotential bonding when they are liable to carry a dangerous potential. Far too often, a coat of epoxy paint, a factory powder coating or an anti-corrosion treatment acts as an unexpected insulator under the head of a fixing screw, preventing any solid contact between two assembled elements.
| Structural element | Frequently observed defect | Corrective action required |
|---|---|---|
| Perforated cable trays | Mechanical fishplates installed without braid or contact claws | Fit a flexible copper bonding jumper or toothed washers on the joint |
| Distribution cabinets | Hinged metal doors without a dedicated protective conductor | Connect a flat earth braid between the door leaf and the fixed enclosure |
| Technical raised floors | Metal jacks insulated by adhesives or plastic pads | Connect the support grid to the main equipotential conductor |
| Equipment supports | Metal cover plates insulated from the receiving chassis | Check the continuity of the contact claw on the fixing insert |
The final phase requires the values to be recorded without any omission. The installation electrician cannot settle for a visual check or a binary pass/fail validation in the field. The measurement record must include the unambiguous identification of each sub-distribution board, the number of the circuit inspected, the type of appliance probed, and the precise ohmic value found when the 200 milliamperes were passed. This test document is the key technical record of the installer's own check, indispensable for preparing the safety report required by the OIBT before the final handover of the works to the client and the independent inspection bodies.
Ohmmeter test procedure: calibrating the test leads and detecting stray loops
The continuity check of the protective conductor and of the equipotential bonding is not carried out with an ordinary multimeter in buzzer mode. NIBT requires a direct current source capable of delivering at least 200 mA at a voltage between 4 V and 24 V. This current makes it possible to break through surface oxidation and to test the mechanical strength of the connections. Before any measurement, calibrating the test leads is essential: using a 50-metre reel adds an inherent resistance of 0.5 to 1 ohm which, without zero compensation, would falsify the entire procedure.
- Isolating the circuitTrip the circuit breaker of the circuit to be checked and make sure there is no voltage at all on the live conductors. Check the insulation of the board to avoid any loop not controlled by the upstream network.
- Compensating for the test leadsConnect the probe tip to the auxiliary conductor run from the main earth bar. Short-circuit the connection at the start terminal and run the tare function on the instrument in order to deduct the inherent resistance of the reel.
- Point-by-point measurementMove the test probe over all the earth pins of the socket bases, the cabinet frames and the metal casings of the luminaires. Read off the stabilised value at each point of use.
- Mechanical testManually move the cable or the connection plug while the test current is being injected. A fluctuating value indicates a terminal tightened onto insulation or a copper strand broken during installation.
The major pitfall on construction sites lies in parallel return paths. A metal casing fixed on a support rail or mechanically connected to a water pipe can show apparent continuity on the instrument even though its green-and-yellow conductor is interrupted in the supply conduit. To remove this uncertainty on final circuits, the phase-protective loop measurement is essential: by short-circuiting the phase and the de-energised protective conductor at the board, the resistance read at the socket outlet must correspond exactly to the sum of the resistances of the phase and of the protective conductor for the cable length installed.
Using the readings, common anomalies and administrative recording
Each raw measurement must be compared with the theoretical value derived from the cross-section and the length of the route. With a copper resistivity of about 0.018 ohm·mm² per metre at ambient temperature, a 1.5 mm² protective conductor laid over a distance of 20 metres has a nominal one-way resistance of about 0.24 ohm. A reading above 1 ohm on a short link invariably betrays an anomaly: a poorly tightened terminal, oxidised contact surfaces or a poorly crimped lug. Any unjustified deviation requires immediate dismantling of the suspected box or appliance, without waiting for the next periodic inspection.
| Measurement finding | Probable origin on the works | Remedial action to restore compliance |
|---|---|---|
| Infinite resistance | Green-and-yellow conductor forgotten or not connected in a box | Open the junctions, locate the loose conductor and crimp a spring terminal. |
| Value fluctuating under tension | Screw clamped onto the insulating sheath or copper sheared during stripping | Cut the conductor back, strip to the recommended gauge and re-insert to the bottom of the housing. |
| Resistance between 1 and 3 Ω | Imperfect contact on lacquered sheet metal or missing serrated washer | Strip the paint back to bare metal and fix with suitable locked fasteners. |
| Stray continuity found | Return path via metal framework or sanitary piping network | Temporarily disconnect the stray exposed part to validate the integrity of the dedicated conductor. |
The recording of results tolerates no approximation. The installer records each measured value in the test record, which forms an integral part of the installation file and of the safety report. General entries such as "OK" are strictly rejected by the inspection bodies and the energy distributors. For each circuit, the report must specify the circuit reference, the cross-section of the protective conductor and the exact figure in ohms. This document engages the technical responsibility of the company and attests that the conditions for rapid tripping of the automatic disconnection devices are met.
Handling critical discontinuities and clearing reservations
A continuity value that cannot be measured or that exceeds the permissible threshold during the acceptance check requires an immediate ban on energising the circuit concerned. In accordance with the requirements of NIBT, the absence of equipotential bonding or of interconnection to the protective conductor nullifies the very principle of automatic disconnection of the supply by circuit breaker or residual current device. If an anomaly is found on a class I appliance or on an extraneous metal part, the electrician locks the circuit in the open position, applies a padlock to the disconnecting device and immediately starts the methodical search for the break point.
- Segmenting the faulty sectionMeasure continuity step by step from the secondary board towards the intermediate junction boxes in order to locate the break: loose terminal, conductor severed during pulling, or incorrect connection to a blind terminal.
- Checking the associated metal partsCheck the actual presence of the connecting fishplates and earth braids on the cable trays, rigid conduits and adjacent metal frames, which are often disconnected during finishing work.
- Mechanical correction and re-making of the connectionsRe-make the faulty connections using standardised spring terminals or by controlled tightening with a torque wrench to the prescribed torques, removing any oxidation layer or insulating paint on the contact surfaces.
- Re-measurement and documentary recordingRepeat the point-by-point measurement with a test current of at least 200 mA in reversed polarity. Enter the final corrected value in the measurement record intended for preparing the final safety report.
If the fault comes from work by another trade modifying the embedded conductors or the building's equipotential bonding, the team leader immediately informs the site management. Under art. 365 CO, the contractor notifies the client of any circumstance jeopardising the proper execution of the works. No notice of completion or safety report required by the OIBT may be issued until all the listed exposed parts show perfect continuity with the installation's earth conductor.
Frequently asked questions
What is the maximum permissible resistance value for continuity of the protective conductor according to NIBT?
NIBT does not set a single upper limit in ohms, but requires a resistance corresponding to the length and cross-section of the copper conductor used. In practice, on final building circuits, a value below 1 ohm (generally between 0.05 and 0.2 ohm after deducting the resistance of the test leads) confirms the effective continuity of the protective conductor and of the equipotential bonding.
How do you measure continuity on a class I luminaire located more than six metres above the floor?
The electrician uses a calibrated measuring reel connected to the earth bar of the distribution board or to a tested compliant socket outlet. The probe tip must make direct contact with the scraped metal casing of the luminaire, de-energised. The measurement is carried out with a current of at least 200 mA, without resorting to visual estimates, which in no way guarantee the tightness of the internal PE terminal.
Why must metal cable trays undergo systematic continuity measurement?
Cable trays can become live if the insulation of a power cable is accidentally damaged. If the connecting fishplates do not guarantee electrical continuity along the route, the cable tray becomes a dangerous floating exposed part. Measurement with a milliohmmeter validates the equipotential bridging from one end of the tray to the other, up to the main earth collector.
Can the continuity measurement be postponed to the final inspection carried out by an independent inspection body?
No. The installer's own check and the final check under the installer's responsibility are an integral part of the installation electrician's obligations before commissioning. The electrician must measure every point and record the data in the test record. The independent inspector appointed under the OIBT verifies compliance by sampling but never replaces the exhaustive readings of the fitter who carried out the installation.
Texts and standards cited
- CO art. 365subject matter and site: immediate notice to the client if a circumstance jeopardises the proper or timely execution of the work (para. 3)
