Key takeaways
- The service entrance box marks the legal transition between the public distribution network and the private internal installation.
- Work on the connection and on the seals remains reserved exclusively for the network distributor's staff.
- Any structural modification of a rising main requires an installation notice to be submitted beforehand to the distributor.
- Working upstream of the main overcurrent protective device requires a network shutdown locked out by the competent operator.
Identify the technical and legal separation point at the service entrance box
On renovation construction sites in French-speaking Switzerland, the most frequent mistake is to regard the whole technical shaft as a private structure accessible to the electrician. The ownership boundary does not follow the walls of the building but is established strictly according to the electricity distributors' requirements and the rules of the trade issued by the industry association. As a general rule, the underground or overhead-underground supply cable linking the public distribution network to the building's main overcurrent protective device is an integral part of the network operator's infrastructure. The internal installation under the owner's responsibility begins immediately at the downstream terminals of this service entrance box.
- Main overcurrent protective device (MOPD)
- Switchgear assembly placed at the point where the service connection enters the building, housing the high breaking capacity fuses that protect the rising main and mark the operating boundary.
In older buildings, the technical situation is often complicated by historical configurations. The network operator sometimes remains the owner of the main rising main as far as the floor distribution boards or the grouped metering boxes in the basement. Before any cutting or dismantling of trunking, the installation electrician must check the legal status of the structure in the building's technical file or with the local distributor. If the rising main has been transferred to the landowner, the latter bears its full maintenance, but the upstream isolating devices remain subject to the operator's exclusive right to intervene.
| Rising main component | Legal owner | Entity authorised to work on it | Access status |
|---|---|---|---|
| External service connection cable | Network operator | Distributor or its agent | Strictly reserved zone |
| Service entrance box and upstream HBC fuses | Network operator | Personnel accredited by the distributor | Sealed or locked |
| Link between service entrance box and floor distributor | Building owner | Licensed installer | Open access under lock-out |
| Floor overcurrent protective device (subscriber fuses) | Building owner | Licensed installer | Private operation |
| Measuring device (electricity meter) | Network operator | Distributor or approved installer under contract | Sealed by the distributor |
Managing the prior request and securing the upstream zone that cannot be de-energised
Any refurbishment or capacity modification of a rising main must begin with formal administrative steps. The electrician submits a complete installation notice to the competent network operator before work starts. This document describes the power required, the condition of the existing installation, the planned ratings and the principle diagram of the connection. The distributor validates the sizing, sets the technical connection conditions and authorises the start of the procedure. Without this written approval, no final energisation of the refurbished installation can be validated at the final inspections.
- Submission of the installation noticeTransmission of the technical form to the network operator specifying the route of the rising main, the conductor cross-section and the planned protection ratings.
- Coordination of the shutdownFormal scheduling of an operating appointment with the network teams for opening, locking out and earthing the service entrance section.
- Verification of absence of voltageOn-site check with an approved voltage detector at the terminals of the service entrance box before starting mechanical dismantling of the conductors.
- Acceptance and re-energisationContinuity and insulation measurements, fitting of new seals by the network representative and issue of the commissioning approval.
The critical hazard in renovation lies in handling the cable heads located immediately downstream of the network connection when the service entrance box does not allow clear, visible isolation. In buildings built before 1980, rising mains often run in cramped masonry shafts where live conductors coexist that the installer cannot de-energise with the means at hand. Any accidental contact or short circuit in this zone causes a high-intensity electric arc, because the upstream breaking point then depends solely on the distributor's local-network protection, rated at several hundred amperes.
Opening historic technical shafts frequently reveals polluting materials that bring the construction site to a halt. Asbestos-cement fire barriers, the insulating braids of old floor distributors and cable gland packings are major sources of exposure to hazardous fibres when core drilling or removing metal conduits. If asbestos-containing products are suspected during the initial inspection of the shaft, operations must stop without waiting for dust to appear. In accordance with art. 82 OTConst, work that releases into the air a significant quantity of asbestos fibres hazardous to health may only be carried out by asbestos-removal companies recognised by the SUVA. The electrician secures the premises, informs site management and waits for certified remediation before installing the new armoured busbars or the halogen-free safety cables.
Ownership boundary and powers to work on the rising main
The ownership boundary between the distributor's (DNO) installations and the internal installation lies at the connection terminals of the main overcurrent protective device (MOPD), housed in the service entrance box. Everything upstream of these fuses, including the underground cable coming from the public domain, belongs to the distribution infrastructure. The distributor retains its technical ownership and exclusive management. Downstream of the output terminals of the main overcurrent protective device, the vertical conductors, floor boxes and links to the meters belong to the building owners. This physical boundary dictates who may do what: the licensed installation electrician may only modify the elements on the internal installation side, in accordance with the NIBT and local technical requirements.
| Component | Owner | Authorised party | Scope of action |
|---|---|---|---|
| Network service entrance cable | Distributor (DNO) | DNO only | Pulling, repair and connection to the low-voltage network. |
| Main overcurrent protective device (MOPD) | Distributor or shared | Sworn DNO personnel | Replacement of sealed fuses, network lock-out and rating selection. |
| Vertical rising main | Building owner | Licensed installation electrician | Sizing, installation of armoured rising mains or cables and floor boxes. |
| Energy measuring devices | Metering owner (DNO) | DNO or installer under contract | Installation of modular meters, remote reading and metrological sealing. |
| Dwelling sub-distribution boards | Co-owner or owner | Licensed installation electrician | Connection of sub-distribution outgoing circuits and residual current circuit breakers. |
Working on rising mains requires identifying common structures and private circuits. In buildings under condominium ownership, the main rising main is a common part, whereas the lines from the subscribers' overcurrent protective devices are private. The installer checks the route of the old conductors in metal conduit or insulating tube. Any slab penetration crossing the fire compartments between floors affects the safety of the structure and requires the agreement of the co-owners' representative before any modification.
Prior request and securing of work in the upstream zone
Any modification of an obsolete rising main requires an installation notice to be submitted beforehand to the distribution network operator. This formality allows the distributor to analyse the load on the local network and to communicate the short-circuit current values at the service entrance point, which are essential for the breaking capacity of downstream devices. In return, the distributor notifies its technical execution conditions: the distribution scheme adopted, the maximum rating of the main overcurrent protective device and the metering arrangements. This prior validation ensures the installation's compliance before the final measurements are taken and the safety report required by the OIBT is issued.
- Submission of the installation noticeTransmission of the technical form and the updated power assessment to the competent electricity distributor.
- Coordination of the network shutdownPlanning of the de-energisation of the network tap with the distributor's operating teams.
- Lock-out of private outgoing circuitsDisconnection of the subscribers' overcurrent protective devices, individual padlocking of the isolating devices and verification of absence of voltage.
- Fitting of insulating protectionInstallation of rigid screens or suitable insulating covers over the live metal parts of the service entrance box.
- Checks before return to serviceInsulation measurements of the rising main, verification of protective conductor continuity and signature of the completion notice.
The presence of live parts that cannot be de-energised in the service entrance box exposes the installer to a risk of electric shock and electric arc. If the distributor cannot isolate the service connection cable upstream, the upper terminals of the main overcurrent protective device remain permanently live. The electrician applies the rules for working near live parts: wearing a face shield certified against short-circuit arcs, insulating gloves checked before use, an insulating mat on the floor and hand tools with approved insulation.
Handling interface disputes, network blockages and work stoppages
On major renovation construction sites in French-speaking Switzerland, working on the rising main regularly exposes the installation electrician to unforeseen situations: advanced deterioration of the terminals upstream of the main overcurrent protective device, obsolete isolators that cannot be operated under load, bare textile-insulated cables, or disagreement with the distribution network operator (DNO) over the precise connection point. When the existing installations do not allow safe lock-out or the ownership boundaries are disputed by the property manager, the heavy-current installation company must freeze the technical situation without taking any unilateral action on the concession domain.
- Joint inspection record and written noticeAs soon as a technical anomaly appears upstream of the private ownership boundary (seized service entrance fuses, charred insulation, lack of earth continuity on the rising main), the foreman draws up a detailed report with photographs and a voltage reading. This formal notice is sent to site management and to the owner to relieve the company of any liability.
- Coordination with the local distributorThe site manager contacts the DNO's technical department (e.g. Romande Energie, SIG, Viteos, OIKEN). If the service entrance box or the underground cable head has to be replaced, only personnel appointed by the distributor are authorised to break the upstream seals and carry out the disconnection on the public low-voltage network.
- Maintaining safety in the zone that cannot be de-energisedAs long as the distributor has not cut the supply upstream, the live parts remain confined behind standardised insulating screens. The team applies the prevention rules of LAA to prevent occupational accidents and adapts the protective measures to the conditions of the distribution room.
In the event of a financial dispute over who bears the cost of replacing an obsolete rising main between several co-owners or with the network operator, the installation electrician must never improvise a temporary connection without a validated prior request. Any re-energisation without a compliant safety report engages the installer's liability.
Frequently asked questions
Who pays for replacing the service entrance box in the event of proven overheating?
Responsibility depends on the contractual interface point set by the distributors' requirements. As a general rule, the supply cable from the public network is the network operator's responsibility, while the service entrance box fixed to the building belongs to the building owner. If the equipment fails through overload linked to the private final distribution boards, the complete replacement of the box and the main overcurrent protective devices is invoiced to the client by the DNO.
What should you do if a distributor's seal has to be broken urgently on a construction site?
Breaking a distributor's seal on one's own initiative is strictly prohibited, even to speed up the cable-pulling work. In the event of imminent danger such as critical overheating or a persistent electric arc, the electrician raises the emergency with the DNO's breakdown service. In the event of accidental opening or opening justified by an incident, the installation electrician sends a written notification to the distributor on the same day so that official joint resealing can be arranged.
Can a rising main supplying several flats pass through private premises?
In older buildings, some rising mains pass through private kitchens or cupboards. In renovation, this configuration creates a major access problem for maintenance and emergency shutdown. Current requirements and the NIBT require the rising main and its floor tap-offs to be installed in common areas that are permanently accessible, such as a stairwell or a dedicated technical shaft, protected against fire by suitable fire-rated walls.
Who works on the floor tap-off upstream of the individual meter?
The floor tap-off terminal block is an integral part of the building's rising main. The work is carried out by the licensed installation electrician holding the installation authorisation, after an installation notice has been submitted to the distributor. The electricity meter, however, remains the exclusive property of the DNO. Only the DNO or its approved agent has the right to install, connect or remove the measuring device and the associated tariff circuit breaker.
Texts and standards cited
- OTConst art. art. 32 OTConstsubstances particularly hazardous to health (asbestos, PCB): work stopped and client informed if found unexpectedly
- LAA art. LAAgeneral prevention rules: the employer takes the necessary measures, adapted to the given conditions and to what the state of the art allows to be applied
