Key takeaways
- The foundation earth electrode must be inspected and accepted before the concrete mixer trucks arrive.
- Galvanised or stainless steel stubs are connected directly to the reinforcement using certified clamps.
- The position of the outlets must correspond exactly to the technical rooms and the planned lightning-conductor down conductors.
- The joint photographic record is the only technical evidence once the raft slab has been concreted.
Coordinating the work on the reinforcement and locking in the connection points
The foundation earth electrode is the heart of the earthing scheme of a new building. Once the concrete has been placed by the structural work contractor (CFC 211.1), no correction can be made inside the raft slab without heavy remedial work by drilling or the costly creation of an external loop in a trench. The electrical installer must therefore intervene within a narrow time window, precisely after the lower reinforcement mat has been laid and before the formwork is closed or the dense upper reinforcement is placed. Compliance with the NIBT rules requires perfect galvanic continuity throughout the entire loop.
The work begins with direct coordination with the structural work foreman. Access to the bottom of the excavation and to the reinforcement mats exposes fitters to the risks of machinery movements and of handling heavy loads by crane. The obligation to wear a safety helmet applies strictly during structural work, in accordance with art. 6 OTConst. Technically, the foundation equipotential bonding is made either with a round or flat steel strip embedded in the blinding or foundation concrete, or by using the structural reinforcement directly as an earth electrode, provided that the joints are electrically and mechanically secure.
| Conductor type | Minimum permitted cross-section | Method of connection | Concrete cover zone |
|---|---|---|---|
| Hot-dip galvanised round steel | Diameter 10 mm | 2- or 4-screw clamps | Minimum cover of 50 mm in the concrete |
| Hot-dip galvanised steel strip | 30 x 3.5 mm | Bolted fishplates or cross clamps | Minimum cover of 50 mm in the concrete |
| Stainless steel (V4A, 1.4571) | Diameter 10 mm or strip 30 x 3.5 mm | Specific stainless steel clamps | Recommended in transition and damp zones |
| Raft slab reinforcing bars | Diameter 10 mm (used as electrode) | Certified bonding clamps or welding | Uncracked concrete, continuity checked per mesh |
The junction points between conductors must be clamped with a suitable tightening torque, generally checked with a torque wrench or by controlled tightening to refusal for M10 bolts (approximately 25 to 30 Nm). Where a waterproofing membrane or perimeter insulation under the raft slab (white tank or thermal tanking) isolates the concrete from the surrounding ground, the NIBT requires the arrangement to be doubled by an external stainless steel earth loop laid in the sub-base or in the blinding concrete beneath the insulation, interconnected with the foundation earth electrode.
Positioning the outlet stubs and recording the photographic evidence before concreting
The point where the metal stubs emerge from the raft slab determines the compliance and neatness of the later connections. Each stub must emerge exactly at the functional location shown on the electrical execution drawings: at the future main distribution board, in the immediate vicinity of the main earthing bar (BPT), and at the vertical drop points of any lightning-conductor down conductors provided for in the lightning protection concept. Bringing an earth conductor out in the middle of a passageway or in a secondary technical room rules out any clean routing later on without an unsightly bridging.
- Marking out axes and setting outTransfer the axis dimensions of the finished walls onto the reinforcement so that the starter bars come out inside the service shafts or wall recesses, with sufficient clearance for the formwork.
- Installing and protecting the emerging section against corrosionUse a stainless steel (V4A) conductor, or protect the galvanised steel for at least 300 mm on either side of the finished concrete surface with a watertight heat-shrink sleeve or a specific anti-corrosion tape to prevent differential aeration corrosion.
- Rigid fixing of the stubFirmly tie the vertical outlet to the upper reinforcement with a metal clamp to prevent any tilting or sinking during pouring and while the concrete is screeded with the vibrating screed.
- Safety marking and labellingCap the end of the stub to prevent the risk of eye or bodily puncture injuries, and mark the conductor clearly with a green-yellow marker.
Before the foreman gives the order to pour, the electrical installer carries out the joint visual check and the measurement of galvanic continuity of the raft slab meshes. Under the contract for work, if the contractor finds that a circumstance jeopardises the proper or timely execution of the work, he informs the client, in accordance with art. 365 para. 3 CO. In our practice as installers, the photographic record is the indispensable evidence document. Once concreting is finished, the physical proof of the electrode's compliance is hidden for ever.
The photographs and the continuity measurement record (resistance below 0.2 ohm between the extreme points of the loop) are immediately added to the technical file of the installation. This file will serve as the incontestable basis for the final inspection required for the safety report (RS) before the building is finally energised by the distribution network operator.
Mechanical connection to the reinforcement and protection of the stubs against corrosion
Connecting the foundation earth electrode to the reinforcement mesh tolerates no makeshift improvisation. Within the thickness of the raft slab, the electrical and mechanical connection between the round steel or strip conductor and the reinforcing bars is made exclusively with dedicated clamps or by autogenous welding carried out according to the recognised rules of the art. The alkaline concrete cover protects plain unalloyed mild steel against oxidation, provided that the contact is mechanically locked before pouring. Improvised ties with tying wire are strictly prohibited by the NIBT: they offer neither the necessary clamping force nor the required stability against the dynamic pressure exerted by the concrete skips or the passage of poker vibrators.
The transition at the point of emergence is the critical failure point of any earth electrode. From the moment the stub passes through the formwork to come out of the concrete into the outside ground, a damp crawl space or the technical slab, the electrochemical corrosion mechanism becomes active and destructive. A black steel or standard galvanised steel bar emerging from the concrete is destroyed by differential corrosion within a few seasons through differential aeration. For each stub intended to connect to the main busbar or the lightning protection system, the emerging section must be made of V4A grade stainless steel (molybdenum steel type 1.4404 or 1.4571) over a minimum length of thirty centimetres in the concrete and fifty centimetres outside the concrete, or must be fitted with a watertight shrink sleeve at the interfaces.
| Installation zone | Prescribed material | Connection device | Installation precautions |
|---|---|---|---|
| Embedded in the raft slab (cover > 50 mm) | Plain unalloyed mild round steel or zinc-plated steel (Ø 10 mm) | Claw clamps or two-bolt jaw clamps | Tightening controlled to the recommended torque; rigid fixing to the lower reinforcement |
| Outlet to indoor board / equipotential bonding bar | V4A stainless steel or tinned copper flat bar under sleeve | Crimp lug or bimetallic branch clamp | Positioned away from run-off water flows and impacts |
| Watertight raft slab penetration (white tank) | Prefabricated watertight penetration with V4A anchor disc | M10/M12 threaded terminals, gas-tight and watertight under water pressure | Installation coordinated with the civil engineer; fixing to the shuttering panel before pouring |
| External emergence to lightning down conductor | V4A stainless steel solid round (Ø 10 mm) | T-connector or heavy-clamp parallel connector | Axis marking in relation to the face of the finished facade; mechanical protection sleeve |
Acceptance protocol, photographic record and clearing of reservations before pouring
Once the concrete skip has been opened, no destructive check, no visual verification and no correction is possible on the foundation earth network. Pouring encloses the work permanently. The electrical installer must plan his final intervention with the masonry foreman in order to carry out a systematic check of the equipped reinforcement, just before the formal authorisation to concrete. If the bars have been modified by the steel fixers when installing punching-shear reinforcement, or if connections have come loose, the electrician applies art. 365 para. 3 CO to notify the client or site management immediately, failing which he bears the consequences of a defective work.
- Continuity check at the stub terminalsMeasure with a calibrated milliohmmeter the electrical continuity between all the stubs brought out before pouring and the entire foundation loop. Check that there is no interruption at any bridged expansion joint.
- Checking the positions and emergence templatesSurvey the position of the connection points in plan and in elevation. Check their strict alignment with the future partitions of the technical rooms, the service shafts and the load-bearing pillars receiving the lightning down conductors.
- Joint photographic campaignTake a sharp, contextualised photograph of each connection clamp, each connection to the V4A stainless steel and each emergence outside the shuttering, with a visible metric reference. Check that the structural axis numbers from the engineer's drawing appear in the photograph.
- Signing the pour release formCountersign with the structural work foreman the self-inspection sheet certifying the compliance of the network before the fresh concrete is mixed and pumped.
The final as-built documents must immediately include all the time-stamped photographs, the as-built plan dimensioned to the millimetre showing the exact position of the buried conductors, and the continuity measurement records. This as-built file guarantees the traceability of the fundamental equipotential bonds, protecting the operator and the installer alike against any challenge to the integrity of the building with regard to the risks of electric shock and atmospheric overvoltages.
Non-conformities, missing stubs and remedial measures
Concreting without prior validation is a point of no return. When the raft slab is poured without the connections having been visually checked, or if a stub has been cut off flush with the concrete by the bricklayers, the buried loop becomes legally and technically unusable. Under art. 365 CO, if a circumstance jeopardises the proper or timely execution of the work, the contractor informs the client. The electrical installer sends written notice to site management before taking any corrective action.
The first check consists of measuring the electrical continuity between the remaining outlets with a milliohmmeter under a minimum test current prescribed by the NIBT. If an essential stub for the technical room is missing, re-tapping by core drilling onto an internal reinforcing bar is strictly prohibited: this practice impairs the structural cover and offers no guarantee of a lasting contact against corrosion.
- Drawing up a joint record of deficiency stating the absence of the stub or the pouring without a prior photographic record.
- Installing a substitute earth loop in an external perimeter trench, buried in open ground below the frost level at a minimum of 70 centimetres, in bare copper or in stainless steel of suitable grade.
- Connecting the external loop to the main board through a watertight opening passing through the buried wall with a certified cable gland.
- Carrying out geothermal drilling or driving deep vertical earth rods if the excavation area has already been backfilled.
Any external replacement solution causes major additional costs and requires an immediate update of the earthing diagrams. The final file handed over at acceptance includes the overall resistance measurement, the routing diagram of the external loop and the disconnection record signed by the site management.
Frequently asked questions
How should you react if a round steel stub has been sheared off flush with the concrete by the masonry company?
Never attempt to weld an extension flush with the raft slab without exposing the cover. The installer records the damage in the site diary. If the continuity to the other outlets is broken or if the reinforcement is inaccessible, the solution is to install an external replacement earth electrode, such as a loop in a trench or vertical rods connected to the main equipotential bonding bar.
What minimum continuity resistance value must be measured on the earth network before pouring?
The continuity between each measuring point and the main stub must be below 0.2 ohm under a test current prescribed by the NIBT. A higher resistance indicates faulty tightening of the fishplates, a conductor break or premature oxidation. Any anomaly requires immediate re-tightening to the prescribed torque before pumping of the concrete is authorised.
Why refuse to connect the foundation earth electrode directly to exposed, uncleaned reinforcement?
Mill scale, loose rust and traces of release oil form an insulating layer that compromises the electrical contact. Connections must use standardised mechanical fishplates that compress the clean metal, without play. Using any reinforcement as an earth electrode without bonding the perimeter ring results in dangerous potential gradients and breaches the rules recognised by the NIBT.
What essential elements must appear on the photographic record before the raft slab is poured?
The photographic file must frame each connection point, the position of the clamps tightened on the reinforcing steel, the continuity of the ring and the waterproofing penetrations. Each photograph must include a clear visual reference locating the structural axis of the building as well as a verifiable time stamp. This material evidence is required at the final inspection before the OIBT safety report is definitively drawn up.
Texts and standards cited
- CO art. 365material and ground: the contractor is responsible for the good quality of the material he supplies; if the material supplied by the client or the ground designated by him is found to be defective, or if another circumstance jeopardises the proper or timely execution of the work, he informs the client immediately, failing which he bears the consequences (para. 3).
