Key takeaways
- Laminated glass maintains physical closure and provides residual safety after impact.
- Toughened glass absorbs thermal and mechanical stresses, but disintegrates instantly without retention.
- In glazed spandrels and guardrails, the occupant retention requirement mandates the use of structural interlayers.
- For thermally toughened glass, the heat soak test eliminates the risk of nickel sulphide inclusions.
Position in the steel frame and occupant retention function
On a steel mullion-transom façade or a metal framework receiving glass units, glazing is not simply infill. Depending on its geometric position relative to the finished floor level and its pitch relative to the horizontal, it performs a structural function protecting building users. The requirement for occupant retention applies as soon as the glazing separates an accessible interior space from a drop presenting a fall hazard. This is typical of low transoms, spandrels integrated into the structural grid, and glass guardrails point-fixed or clamped onto load-bearing metal profiles.
- Residual safety
- The mechanical capacity of a glazed element to remain in its rebate and support its own weight as well as temporary residual pressure after the failure of one or more of its glass components.
In spandrels and guardrails, the failure of monolithic toughened glazing causes the immediate collapse of the pane into countless small, non-cutting fragments. Although this failure mode reduces severe lacerations for the person causing the impact, it immediately opens a gaping void, destroying all protection against falling through the opening. This is why laminated glass with residual safety is essential in this configuration: the interlayer holds the broken pieces together and absorbs the kinetic energy, maintaining the physical barrier until the element is replaced.
| Position in the façade | Dominant loads | Required post-breakage behaviour | Recommended composition |
|---|---|---|---|
| Glazed spandrel (height below 1 m) | Soft-body impact, horizontal pressure | Maintenance of the physical fall-prevention barrier | Safety laminated (2x toughened or 2x heat-strengthened) |
| Guardrail on steel mullion | Linear top load, point impact | Residual stability of the screen without critical deflection | Structural laminated toughened or heat-strengthened |
| Glass roof and pitched glazing | Snow, wind, hail impact, maintenance | No falling fragments downwards | Inner pane in laminated with float or heat-strengthened |
In glass roofs or rooflights on steel rafters, the mechanism is reversed depending on the pane considered. The outer pane is subjected to climatic loads and thermal stresses, often justifying toughened glass. The inner pane, facing the occupants, must strictly prevent the fall of heavy shards. Monolithic toughened glass is strictly prohibited on the underside: breakage would unleash a shower of dense debris dangerous to people below. The underside therefore requires laminated glass whose interlayer prevents the collapse of the shattered sheet.
Managing spontaneous breakage of toughened glass and choosing the right laminated type
Thermally toughened glass offers increased resistance to temperature variations and to bending under high wind loads. However, this toughening process generates an internal state of high stress: the core of the glass is under permanent tension while the surface is compressed. If a microscopic nickel sulphide inclusion is present in the raw material, it undergoes a slow crystalline transformation over time. This phase change causes a localised increase in volume at the core of the pane, initiating a crack that triggers sudden disintegration without any external load: this is spontaneous breakage.
To eliminate this risk on toughened elements without laminated interlayers or elements presenting a risk of falling onto the public domain, an accelerated ageing heat soak test is required. By subjecting the glazing units to a controlled heating dwell in the factory, this protocol triggers the failure of panes containing critical inclusions prior to delivery to the construction site. For composite façades, the metal construction contractor must ensure that this process is specifically prescribed for toughened elements.
- Standard toughened glass: high mechanical strength, but complete destruction with no retention upon failure.
- Heat-strengthened glass: fragmentation similar to annealed glass, free of the risk of destructive nickel sulphide.
- Laminated glass with polyvinyl butyral films: excellent residual adhesion, sensitive to creep under high heat.
- Laminated glass with rigid ionomer interlayer: high post-breakage strength, suitable for free-standing guardrails fixed to steel.
When the application combines heavy retention loads with exposure to hot outdoor conditions, standard interlayers carry a risk of softening that destroys the stiffness of the glass after breakage. The use of rigid structural interlayers guarantees sufficient load-bearing capacity for the guardrail or spandrel to maintain its geometry without bending into the void. Adhering to these design principles complies with the technical rules mandated by recognised building standards, just as the site manager complies with art. 82 LAA to organise prevention and adapt safety measures to the real installation conditions of heavy elements.
Art. 229 CP penalises anyone who, when directing or carrying out a construction project, intentionally breaches the recognised rules of the trade and knowingly endangers the life or physical integrity of persons.
art. 229 CP
Mechanical behaviour and residual safety according to location
In a steel-framed load-bearing façade, glazing design is not based solely on resistance to wind loads or initial impacts. The nature of the breakage directly determines whether the structure maintains its integrity or exposes users to falls from height or to falling sharp debris. Standard thermally toughened glass (ESG) provides high mechanical bending strength under wind loads, but its total disintegration into countless small, non-cutting fragments instantly destroys all load-bearing capacity. It offers no residual safety when used alone.
Conversely, laminated glass (VSG) maintains the cohesion of the screen thanks to its polymer interlayer, generally polyvinyl butyral (PVB) or a structural ionomer. During an impact or cracking event, the glass fragments adhere to the plastic film. This configuration ensures that the glass plane remains within the metal rebate and provides temporary mechanical stability, which is essential to prevent accidental pass-through or to hold fragments at height until the maintenance team intervenes.
| Position in the building | Primary requirement | Minimum recommended composition | Post-breakage behaviour |
|---|---|---|---|
| Opaque or translucent spandrel | Occupant retention and resistance to interior impacts | Laminated glass (VSG) with heat-strengthened (TVG) or toughened (ESG) panes | Retention within the steel frame, deformation as a flexible membrane without breach opening |
| Surface-mounted guardrail on steel structure | No overturning after impact, limitation of fragments | Laminated glass composed of two toughened or heat-strengthened panes with structural interlayer | Sufficient residual stiffness to prevent falls into the void if one of the two components shatters |
| Pitched rooflight or glazed roof | Non-fall-through performance and absolute protection against falling fragments | Bottom pane strictly in laminated glass (VSG) | Total retention of fragments beneath the frame, mechanical suspension of debris by the film |
Assembly execution, tolerances, and thermal validation
The integration of safety glazing into a heavy steel façade requires strict coordination of packing and clamping. Point stresses transmitted by a mullion lock or a clamping plate can induce stress concentrations that are fatal to toughened glass, or cause the premature delamination of laminated glass interlayers due to standing moisture in the rebate.
- Setting blocks and edge clearanceUse rot-proof glazing packers of appropriate hardness, positioned on the metal transoms directly in line with stiffeners. Rebate clearance must strictly be respected to prevent any direct contact between steel and glass during differential thermal expansion.
- Drainage and ventilation of rebatesCheck the free circulation of air along the edges of the laminated glass. Metal rebates must incorporate weep holes to prevent prolonged contact of glass edges with condensate, which breaks down PVB adhesion.
- Inspection of the Heat Soak Test thermal treatmentFor thermally toughened glass panes installed as non-laminated spandrels or on external façades, systematically demand the test certificate of the accelerated heat soak test in order to neutralise the risk of nickel sulphide inclusions prior to delivery to the construction site.
- Controlled torque of clamping profilesApply the prescribed tightening torques with a torque wrench to the stainless steel screws secured into the steel profiles. Over-compressing the EPDM gaskets creates hard spots and restricts the natural movements of the framework.
The installation foreman records the packing and torque inspection sheets in the site log. In the event of non-conformance of the load-bearing framework geometry that would cause racking of the glazed frame, the metal construction contractor applies the duties of care specified in the works contract before installing translucent elements under mechanical stress. Under art. 229 CP, breaching the recognised rules of the trade when directing or carrying out a construction project incurs criminal liability if physical endangerment occurs.
Managing glazing damage on metal framework: emergency protocol and responsibilities
The unexpected failure of glazing during construction or after handover directly affects the residual stability of the assembly and the protection of individuals. Faced with shattered toughened glass or cracked laminated glass under load, the installation foreman executes a strict sequence: securing the drop zone, analysing the failure mechanism, and issuing formal notification.
- Cordoning and isolation of traffic zonesImmediately prohibit access beneath the affected area, both at ground level and on lower floors. For a spandrel or edge glazing, install temporary steel barriers secured to the façade mullions to physically restore the occupant retention requirement.
- Mechanical stabilisation of damaged glazingIf laminated glass in a roof or rooflight exhibits folded ruptures, prop it from underneath using a propping tower and timber baulks distributing the load. Never attempt to remove a broken pane without vacuum lifters featuring a redundant vacuum circuit and textile restraint straps.
- Technical survey and joint inspection recordPhotograph the impact point or the butterfly pattern characteristic of a nickel sulphide inclusion before any cleaning. Measure the rebate clearances on the metal framework using a micrometer to verify the absence of unexpected steel-to-glass binding.
- Contractual notificationDraft a formal notification recording the pane references, factory inspection certificates, and climatic conditions at the time of the incident for immediate submission to the site management.
The metal construction contractor remains responsible for the conformity of the assembly. Art. 229 CP penalises anyone who intentionally or through negligence breaches the recognised rules of the trade while directing or executing construction work, knowingly endangering the life or physical integrity of persons. Strict adherence to packing procedures and installation guidelines protects the team against sudden failure risks.
Frequently asked questions
What should be done when toughened glass shatters spontaneously in a spandrel after installation?
Cordon off the lower area to block falling residual fragments. Check whether the glass possessed a Heat Soak Test certificate in accordance with order requirements. Immediately install a temporary guardrail secured to the metal mullions to satisfy the occupant retention requirement. Notify the damage in writing to the site management, attaching photographs of the setting blocks and edge clearances.
How can thermal shock breakage be distinguished from a nickel sulphide failure?
Thermal failure starts perpendicular to the glass edge, generally adjacent to a shaded zone cast by a metal capping or flashing, and then travels in meandering paths. Spontaneous breakage due to nickel sulphide shatters the toughened glass instantly and produces a characteristic central figure with two radiating nodes, known as a butterfly wing pattern, located at the origin of the break.
Why is monolithic toughened glass prohibited on the inner pane of a glazed roof?
In roofs, the inner pane must provide absolute residual safety. Monolithic toughened glass disintegrates instantly into thousands of small pieces that shower the space below and removes any physical barrier. Only laminated glass ensures occupant retention and arrests metal or glass debris thanks to the adhesion of its rigid interlayers in the event of breakage under accidental load.
Can broken laminated glazing be replaced without removing the entire pressure plate system?
No. On a composite façade or a metal rooflight, dismantling the external clamping profile requires relieving the continuous pressure exerted on adjacent panes. Locally removing screws without temporary clamping disrupts the adjoining EPDM gaskets and can generate fatal stress concentrations along the edges of the intact glass. A coordinated removal procedure is mandatory.
Texts and standards cited
- CP art. 229breach of the recognised rules of the trade: whoever, when directing or carrying out a construction or demolition project, intentionally breaches the recognised rules of the trade and knowingly endangers the life or physical integrity of persons is liable to a custodial sentence not exceeding five years or a monetary penalty; in the case of negligence, not exceeding three years or a monetary penalty.
