Skip to content
Website
🧱 CFC 241Brazing, hot work permits and safety in the boiler roomChapter 4 of 10 in the section

Water at eighty degrees: bleeding, draining and avoidable burns

This chapter details the thermal and hydraulic securing procedure before any bleeding or draining of a heating system. You will learn how to neutralise residual pressure, how to organise the controlled cooling of the sections to be worked on, and how to choose personal protective equipment to prevent any accidental contact with a high-temperature heat-transfer fluid.

Key takeaways

  • Shut down heat generation and electrically isolate the circulators before handling any hydraulic component.
  • Wait until the heat-transfer fluid has cooled below the critical threshold before starting to open the circuit.
  • Release the operating pressure gradually through a drain routed to the sewer.
  • Wear a full face shield, covering clothing and watertight gloves suited to the temperature.

Shutdown and controlled depressurisation of the heating network

Work on a high-temperature hydraulic distribution network exposes the fitter to a direct risk of second- or third-degree burns. Superheated water at two to four bar of static pressure gives no warning: the unintended opening of a bleed screw or a fitting releases a jet of water and steam that strikes the hands and face in a fraction of a second. In accordance with art. 3 OPA, the employer takes the protective provisions and measures that meet the recognised rules of technology to prevent such bodily injury. Any dismantling or draining therefore requires a complete and verifiable shutdown of the heat energy sources.

  1. Lockout of generators and switching off the pumpsCut the electrical supply to the burner or heat pump and switch the zone circulators off. Lock the isolators to prevent any automatic restart triggered by the weather-compensated control.
  2. Isolating the hydraulic sectionsClose the manual shut-off valves on the flow and return of the riser or appliance to be serviced. Confining the fluid avoids discharging the building's entire volume of water.
  3. Monitoring the temperature dropCheck the contact thermometers or use an infrared thermometer on the metal pipework. Mechanical work only begins once the fluid has dropped below 40 °C.
  4. Depressurisation via a connected drain cockConnect a textile-braid reinforced hose to the KFE-type drain cock, directing its end towards a wastewater discharge point. Open the plug very slowly to release the static pressure shown on the pressure gauge.

A pressurised expansion vessel maintains a continuous force against the isolating components. During a partial drain, the diaphragm pushes the water towards the low point. If the isolating valve of the expansion vessel is not closed during work confined to the boiler room, the buffer volume of hot water continues to be pushed towards the operator. The air vent at the high point of the circuit must only be loosened by half a turn after complete depressurisation at the low point, solely to let in the atmospheric air needed for the column to drain by gravity.

Personal protective equipment and technical opening procedures

Even after a thermal rest period has been observed, a local thermosiphon effect, a pocket of water trapped in a heating element or a sealing failure of a butterfly valve can retain a mass of water at 80 °C. Under art. 82 LAA, the employer must provide equipment suited to the actual working conditions, and the worker is obliged to use it to assist the company in preventing accidents causing bodily injury. The heating technician approaches a vent or a discharge cock only when wearing a complete set of watertight, heat-resistant equipment.

Minimum safety equipment for opening and draining circuits with residual heat
Required equipmentTechnical requirement of the tradeRisk neutralised
Flip-up face shieldPolycarbonate screen covering chin and foreheadDirect splash of boiling water and steam
Long-cuff glovesHeavy nitrile rubber, cotton liningThermal burns to the hands and water ingress at the wrists
Closed work jacketDense cotton with no meltable synthetic materialHot fluid running down the torso
S3 safety shoesWater-repellent leather with non-slip solePools of boiling water on the floor and burns to the feet

The position of the body when unscrewing the needle screw of a radiator or operating a safety valve determines the severity of injuries in the event of an incident. The fitter must always stand back, to the side of the leak axis of the outlet. No face should be in the plane perpendicular to the vent. The vent body must always be wrapped in a thick cotton cloth during the operation: this fabric absorbs the initial jet, breaks the kinetic energy of the droplets and directs the dripping towards the drain bucket held away from the chest.

When the water discharged is laden with corrosion sludge or chemical inhibitors, the thermal burn is compounded by skin irritation. Soiled work clothing must be removed without delay and the skin rinsed abundantly under lukewarm running water for at least fifteen minutes. Maintaining a strict slow-decompression protocol together with systematic wearing of the face shield protects personnel against unexpected residual discharges.

Channelling discharges and managing depressurisation in the boiler room

Draining a section or distribution riser must never be done by simple open-ended gravity discharge, particularly when the heat-transfer fluid is at high temperatures of around 70 °C to 80 °C. Even after the burners have been stopped or the mixing valves switched over, the thermal mass stored in the heat exchangers, condensing boilers or primary networks requires a strict technical delay. Opening a bleed valve without channelling the jet exposes the operator to instantaneous flashing of superheated water as it expands to atmospheric pressure.

Systematically connecting a metal-braid reinforced hose or a high-temperature-resistant rubber hose is the rule at every drain point. This hose must be firmly secured by a watertight threaded mechanical fitting and directed to a floor drain or a retention tray suited to hot effluents. Free discharge into a plastic site bucket is prohibited: under the impact of water at 80 °C, standard thermoplastic polymers deform abruptly, causing the container to tip over and the liquid to spill onto the heating fitter's lower limbs.

Comparison of bleeding and draining methods on pressurised networks
Method of interventionThermo-hydraulic behaviourThermal risk levelRequired precautions
Direct bleeding at a manual air ventRelease of a two-phase air-steam mixture with radial sprayVery high: direct risk of corneal and facial burnsPrior depressurisation, full face shield, thick cloth wrapped around the air separator
Draining via the riser base cock onto a hoseGuided flow under residual pressure, risk of the hose whippingModerate, provided the hose is firmly secured to the drainCheck the mechanical tightness of the fitting, watertight heat-resistant gloves
Removing an automatic air vent without an isolating valveSudden release of the water column with ejection of sludge and boiling waterCritical: instant thermal flooding of the work areaShutdown, closing the upstream and downstream valves and pressure drop to zero bar
Draining after controlled cooling below 40 °CLaminar flow at low temperature with no dangerous vapour pressureLow: spray risk neutralised at the sourceThermographic check or validated pressure and temperature gauge reading

Controlled depressurisation is organised before any mechanical dismantling. The installer monitors the pressure gauge of the safety group or manifold until it has fully stabilised at zero bar. Particular attention must be paid to diaphragm expansion vessels: a stuck diaphragm or residual pre-charge pressure can mask a pocket of superheated water that is released violently when the last threads of a screwed fitting are loosened.

Compliance under the OPA, physical lockout and personal equipment

Under art. 3 OPA, the employer takes the protective provisions and measures that meet the requirements of the ordinance, the other applicable occupational safety provisions and the recognised rules of safety technology and occupational medicine. In the context of a heating plant, this obligation means putting in place a formal lockout procedure for the circuits before any operation involving the primary fluid.

Shutting down is not limited to switching off the supply to a circulator. The works manager or team leader ensures the mechanical locking of the shut-off components. Isolating butterfly valves or quarter-turn cocks must be locked out with physical blocking devices and fitted with a warning tag prohibiting their operation. This precaution ensures that an inflow of mains water or an automatic restart of a pump does not inject a new pressurised load while a vent is open upstream.

  1. Electrical and hydraulic lockoutSwitch off the boilers and circulators at the local isolator in the boiler room, close the flow and return valves of the circuit concerned, then lock the handles with padlocks.
  2. Checking depressurisationRead the loop pressure gauges and carefully operate the test relief valve or the discharge cock into a container to verify that there is no residual static load.
  3. Complete personal protective equipmentPut on the flip-up polycarbonate face shield with anti-fog treatment, the long watertight heat-insulating gloves and a covering flame-retardant work jacket closed at the wrists.
  4. Gradual and directed openingLoosen the bleed square with a suitable tool, turning the jet away from the body and placing a waterproof textile screen in front to deflect direct sprays of condensed steam.

In the event of equipment failure resulting in a jet of hot water to the face or hands, the emergency protocol requires continuous rinsing with lukewarm water for at least fifteen minutes to stop heat spreading in the skin tissue, together with an immediate call to the medical emergency services. Any clothing soaked in scalding water must be removed without delay if it does not stick to the skin.

Emergency protocol and management of thermal burns in the boiler room

When heating water at eighty degrees is accidentally sprayed during a faulty bleeding or draining operation on a primary network, every second counts in limiting the extent of tissue damage. The rupture of a flexible connection hose or the uncontrolled discharge from a valve under two to three bar of pressure sprays boiling fluid capable of causing deep second- or third-degree burns in a fraction of a second.

  1. Raising the alarm and making the room safeImmediately cut the supply to the circulator if the emergency switch is accessible out of reach of the jet, then evacuate the plant room to avoid inhaling dense steam.
  2. Immediate thermal coolingRinse the burn with lukewarm running water, between fifteen and twenty degrees, for a minimum of fifteen minutes. The use of ice, ice-cold water or greasy substances is strictly prohibited.
  3. Careful handling of soaked clothingQuickly remove clothes soaked in hot fluid before the heat penetrates the deeper layers. If the fabric sticks to the skin, do not pull it; cut around the adhering fabric.
  4. Medical care and sterile dressingProtect the wound with a non-compressive sterile dressing or a clean cloth. Call the emergency services on 144 if the face, neck or a large body surface is affected.

In accordance with art. 3 OPA, the employer takes the protective provisions and measures that meet the requirements of the ordinance, the other applicable occupational safety provisions and the recognised rules of safety technology and occupational medicine. On the construction site, this requirement means checking that an operational first-aid kit is available, containing dressings specific to thermal burns and an eye-rinsing solution. The technical analysis following the accident is then used to identify the material cause of the failure, to check the condition of the bleeding equipment and to formally record the corrective measures essential before the installation is repressurised.

Frequently asked questions

Why is it forbidden to open an air vent on a pressurised network at 80 °C?

Directly opening an air vent on a manifold or radiator under a pressure of 2 to 3 bar suddenly releases a two-phase mixture of hot water and flash steam. At eighty degrees, this conical jet instantly sprays the face and hands, destroying the epidermis in less than a second. The installer must first isolate the section, stop the circulation pump and wait for it to cool below forty degrees before discharging the residual air.

Which gloves must the installer wear to drain a heating riser?

Standard leather or thin knitted gloves are prohibited: they soak up boiling water and worsen the burn by retaining heat. The fitter must wear watertight gloves in heavy nitrile or neoprene with a thermal lining, approved against chemical and contact heat hazards. These must have long cuffs that cover the forearms and must be worn under the sleeves of the work jacket to prevent any internal flow of scalding water.

What to do if a draining component breaks off cleanly during the operation?

If a fitting or a drain cock gives way under pressure, never try to plug the leak by hand or with a cloth. The installer must retreat out of the spray area, cut the emergency switch of the boiler room to stop the circulators, then close the main isolating valves of the group concerned. Complete depressurisation of the circuit via the boiler room is required before any mechanical repair on the faulty section.

Why is a full face shield required instead of safety glasses?

Simple safety glasses only protect the frontal eye socket. When bleeding a seized air vent, the sudden release creates a lateral vaporisation effect and upward splashes. A full polycarbonate face shield covers the whole face, chin and neck, thus preventing sprays of water at eighty degrees onto mucous membranes and skin. It is worn over the glasses to guarantee complete visual sealing against jet backflow.

Texts and standards cited

  • OPA art. 3protective measures and installations: the employer takes the protective provisions and measures that meet the requirements of the ordinance, the other applicable occupational safety provisions and the recognised rules of safety technology and occupational medicine.

In the same section