Skip to content
Website
🧱 CFC 241Brazing, hot work permits and safety in the boiler roomChapter 2 of 10 in the section

Clearing the surroundings: distance to combustibles, heat shield and cavities

This chapter teaches you how to define the safety perimeter around a brazing or welding station in a boiler room. You will know how to neutralise sparks and spatter with suitable fire-resistant blankets, fit rigid heat shields and seal the cavities around pipe penetrations to block any smouldering fire starting in the insulation.

Key takeaways

  • A circular clearance of ten metres remains the basic rule before lighting a torch.
  • Any glowing metal spatter bounces and works its way into the smallest gaps of nearby thermal insulation.
  • Silica-fibre blankets and rigid shields protect adjacent combustible walls.
  • Airtight sealing of wall and floor openings and sleeves cuts off the air draught and stops insidious fire starts.

Define the range of spatter and clear the area

When braze-welding copper manifolds or gas-welding distribution pipes in a boiler room, the flame of the oxyacetylene torch is not the only danger. Slag beads, drops of brazing alloy and sparks from cutting or from fitting work with a grinder retain enough heat to ignite a material several metres away. A red-hot steel bead easily rolls across a smooth screed, crosses a door threshold or drops into a technical trench.

Work is planned so that the risk of occupational accidents, occupational diseases or harm to health is as low as possible.

art. 3 OTConst

This planning requires the work area to be methodically cleared before any ignition. The guideline of the Association of Cantonal Fire Insurance Institutions on hot work sets a strict principle: clear the space around the workstation. As a general rule, no combustible material may remain within a horizontal radius of ten metres and a free height equivalent to it below the ceiling.

Safety measures according to distance from flammable materials
Distance from workstationCondition of the areaAction required on the construction site
Less than 5 metresDirect exposure zoneComplete removal of pallets, cardboard, solvents and synthetic foams.
Between 5 and 10 metresParticle rebound zoneRemoval or containment under heavy fire-resistant blankets weighted down on the floor.
Beyond 10 metresPossible extension zoneVisual check of open floor and wall openings, shafts and open trenches.

When fixed combustible items cannot be moved, for example an electrical control panel, cable ducts or buffer tanks insulated with rigid foam, distance alone is no longer enough. It becomes essential to erect a physical barrier that is tight against flames and glowing metal beads.

Fitting heat shields and sealing cavities and openings

The heat shield has two distinct functions: stopping glowing particles in flight and shielding against the continuous thermal radiation of the torch. To protect a light partition or timber frame in the immediate vicinity of a pipe to be brazed, heating installers use rigid asbestos-free refractory calcium silicate boards or flexible glass-fibre or silica-fibre cloth blankets.

  • Flexible fire-resistant blanket: essential for wrapping pipework already installed or draping cable trays below the work area.
  • Rigid refractory plate: placed directly between the pipe to be brazed and the wall to block the tip of the flame and concentrate the heat on the fitting.
  • Heat-barrier paste: applied to the copper to prevent conduction from melting the adjacent insulation or damaging the seals of upstream valves.
  1. Locating penetrations through slabs and wallsVisually inspect every pipe passage within a radius of ten metres. Examine open sleeves, unfilled core holes and the slab's expansion joints.
  2. Tight sealing of openingsPlug every opening with reusable fire-stop cushions, water-soaked rags or non-combustible insulation rolls of firmly packed rock wool.
  3. Protecting neighbouring insulation sectionsCover the cut ends of elastomer or polyethylene insulation sleeves with a strip of refractory fabric to prevent spatter from reaching them.
  4. Instrumented thermal monitoringCheck for hot spots in slits and ducts with an infrared thermometer as soon as the torch is extinguished, then at regular intervals.

Safety perimeters and trajectory of glowing spatter in boiler rooms

During brazing with an acetylene-oxygen torch or gas welding on steel heating distribution pipes, the shower of sparks and molten slag beads do not simply fall vertically below the joint. Thrown by the pressure of the flame or when a pipe is tapped, these glowing particles bounce off smooth concrete floors or technical trenches and can travel a horizontal trajectory of up to ten metres. The temperature of these fragments regularly exceeds 800 °C, a value more than sufficient to cause flameless ignition of an insulation panel or accumulated dust.

In boiler rooms and technical basements, the coexistence of primary pipework and combustible insulation requires rigorous delimitation. Art. 3 para. 1 OTConst provides that work is planned so that the risk of occupational accidents, occupational diseases or harm to health is as low as possible. In the organisation of a heating construction site, this obligation means removing all combustible waste, wooden pallets and cardboard packaging from boilers or heat pumps within a free radius of at least five metres around the fixed assembly station, and protecting everything that remains immovable within a radius of ten metres.

Clearance measures according to the nature of the materials and the layout of the room
Room layoutCombustible materials presentMinimum distance without shieldAction required if distance is insufficient
Open boiler roomCardboard, pallets, workshop rags5 metresPhysical removal from the room before lighting the torch
Vertical service ductPolyurethane insulation, electrical wiring10 metresFitting rigid heat shields and a sealed fire-resistant blanket
Passage under ceilingPolystyrene panels, light linings5 metresPrior wetting and placing a silicone-coated glass fabric in between
Technical floor trenchSawdust, oil residues10 metresCleaning with an industrial vacuum and covering with sheet steel

Direct visual monitoring alone is not enough to guarantee the absence of danger. Fine sparks thrown at high speed can bounce off a flange or pipe support, change angle and end up behind an acoustic false ceiling or under a technical platform. The material preparation of the flame zone must therefore come before any connection of the torch hose to the gas regulators.

Containing penetrations, sealing voids and installing heat shields

The most insidious danger for the heating installer lies in wall openings and slab penetrations. When a black steel pipe intended to supply a manifold passes through a fire wall to reach a rising duct, the annular space around the pipework forms a chimney. A molten bead thrown during welding enters this gap, rolls several metres and comes into contact with the duct insulation: polyethylene foam, expanded polystyrene residues or old cork. Slow combustion can then smoulder for several hours, sheltered from the open air, before turning into a full-blown fire.

  1. Careful examination of walls and floorsInspect all surfaces within the thermal spatter cone. Locate masonry cracks, unsealed core holes, gaps under skirting boards and expansion joints where flammable residues may lodge.
  2. Temporary sealing of cavitiesPlug every gap with compacted rolls of non-combustible rock wool (melting point above 1000 °C) or quick-setting fire-stop mortar. Standard aerosol sealing foams are absolutely prohibited during this preparatory work.
  3. Mechanical fixing of protective shieldsPosition rigid calcium silicate heat shield boards or treated glass-fibre fire-resistant blankets. Make sure the blankets cover the floor over a continuous width, leaving no gap at skirting boards or internal corners.
  4. Checking the tightness of the coveringsOverlap the protective sheets by at least 20 centimetres at each joint. Hold them in place with metal clamps or non-combustible weights to prevent any lifting from the room's air current or the blast of the torch.

Where manoeuvring space is limited, for example when replacing a mixing valve against a partition lined with insulation, the shield must be slid directly behind the heating zone. Multilayer aluminised heat shields lined with a refractory face are then used, capable of absorbing the radiation without transmitting heat by conduction to the backing panel. Art. 229 CP punishes anyone who, while directing or carrying out construction or demolition work, intentionally or negligently breaches the recognised rules of the trade and knowingly endangers the life or physical integrity of persons. Disregarding safety distances or failing to protect combustible walls during brazing is a direct breach of these rules of the trade.

Response protocol in case of glowing infiltration and responsibilities

When a bead of brazing spatter or a spark slips into a heating service opening or behind a combustible insulation, such as an acoustic lining or thermal insulation on the underside of a slab, the fire almost never announces itself with a visible live flame. The glowing particle penetrates deep into the gaps of the building structure. The fire smoulders there silently for several hours, fed by the weak air draught of an unsealed service duct, before suddenly breaking through.

  1. Cut off the fluidsStop welding, extinguish the torch and close the gas valves on the site cylinders.
  2. Locate the emberInspect the adjacent cavities with a thermal camera to identify invisible heating behind the cladding.
  3. Attack and open upUse the appropriate extinguisher, then mechanically remove the insulation or insulation section to drown the residual ember.
  4. Alert the emergency servicesCall 118 without delay if a hot spot persists or if smoke escapes from an inaccessible construction void.

Site organisation must anticipate this drift. According to art. 3 OTConst, work is planned so that the risk of occupational accidents, occupational diseases or harm to health is as low as possible. In the practice of the heating fitter, this planning means marking out a combustible-clearance radius of at least five metres, pressing rigid heat shields against woodwork and stuffing every floor opening with a temporary fire-stop mat before the first strike of the flame.

After a fire start or abnormal heating of insulation has been fully brought under control, the team leader maintains a rigorous technical monitoring round on site for at least two hours, with instrumented checking of the temperature of the walls passed through, the false ceilings and the ducts on the lower floors.

Frequently asked questions

What minimum distance must be kept between the torch and a combustible wall insulation?

When the installer brazes steel or copper heating pipes, a free distance of five metres around the workstation is the accepted rule for keeping all flammable material away. If this distance cannot be kept in a cluttered boiler room, fitting rigid heat shields or textile blankets classified as non-combustible is essential to protect insulation panels or light partitions directly from thermal radiation and sparks.

How do you effectively seal a pipe penetration opening before welding?

Before starting gas or arc welding of a heating pipe passing through a floor, the gap of the opening must be hermetically plugged. Fire-stop mats or cushions of compressed rock wool are preferably used, sometimes backed with a fitted metal sheet. This mechanical barrier blocks the glowing slag falling beneath the joint and prevents it from dropping to the floor below, where flammable materials could ignite.

Why is an ordinary textile sheet not suitable as a heat shield?

Polyethylene or conventional cotton sheets present a major risk: they melt or ignite under the impact of a drop of molten metal from brazing. In a boiler room, the fitter must use only certified fire-resistant cloths made of silicone-coated glass fibre or silicate. These fabrics withstand temperatures above seven hundred degrees without transmitting heat by contact to neighbouring pipework or underlying insulating linings.

How long must the area be monitored after the torch is extinguished?

A safety round is required after every thermal intervention on the distribution network. Visual monitoring and tactile or thermal checking of nearby elements must continue for a minimum of two hours after work stops. This precaution makes it possible to detect in time a slow combustion or insidious heating hidden in a thermal insulation section, thus avoiding a delayed fire start after the teams leave the construction site.

Texts and standards cited

  • OTConst art. art. 3 OTConstplanning of construction work: work is planned so that the risk of occupational accidents, occupational diseases or harm to health is as low as possible
  • CP art. art. 229 CPbreach of the recognised rules of construction: anyone who, while directing or carrying out construction or demolition work, intentionally breaches the recognised rules of the trade and knowingly endangers the life or physical integrity of persons faces a custodial sentence of up to five years or a monetary penalty; if through negligence, up to three years or a monetary penalty

In the same section