Key takeaways
- Draining the circuits requires a clear separation between raw process water and glycol-based fluids.
- Sorting metals on site maximises the financial recovery value of steel, cast iron and copper.
- Any suspect insulation requires work to stop for analysis before any handling or placing in a skip.
- The tracking form for special waste guarantees the regulatory traceability required by Swiss environmental law.
Draining the circuits, capturing the fluids and methodically recovering the metals
Clearing an obsolete boiler room does not begin with the sledgehammer, but with the complete and controlled draining of the hydraulic circuits. Two hundred litres of heating water blackened by magnetite, saturated with corrosion inhibitors or mixed with monopropylene glycol must never reach the clean-water drainage network or the municipal sewers without prior checking. The technician begins by testing for antifreeze with a refractometer. Heavily loaded or glycol-containing process water must be pumped into sealed workshop drums or containers of the cubitainer type for treatment through a dedicated channel.
Once the installation has been drained, mechanical dismantling follows the recycling channels. The metal components account for the main volume and the first source of material recovery, provided they are not soiled by hydrocarbons or thrown together indiscriminately.
- Removing the burner and draining itRemove the oil or gas burner. Disconnect the hydraulic hoses and drain them over a containment tray to catch any residual drops of hydrocarbons.
- Cutting and sorting black steelCut up the sheet-steel boiler bodies, buffer tanks and risers. Heavy iron and steel are separated from thin casing sheet.
- Dismantling the cast-iron sectionsSplit with a hammer or uncouple the grey cast-iron boiler sections. This clean, dense metal is bought back at a specific price by the scrap dealer.
- Separating non-ferrous metalsDismantle the copper manifolds, pipes and fittings. Remove the brass and bronze valve bodies after taking off the motors and actuators.
This rigorous sorting at the workbench or in the boiler room not only protects the environment but also guarantees the best buy-back price for the scrap from metal recovery companies in your region of French-speaking Switzerland.
Insulation, special waste channels and documentary traceability
The ordinance on the avoidance and disposal of waste precisely governs the management of materials from construction sites. Under art. 17 OLED, special waste is separated from other waste and disposed of separately, the remainder being sorted on the construction site.
| Type of waste | Regulatory status | Swiss disposal channel | Proof required |
|---|---|---|---|
| Glycol water or heavily contaminated water | Special waste | Cantonal fluid treatment centre | Special waste tracking form |
| Complete burner and circulation pumps | Waste electrical equipment | Electronic appliance take-back channel | Weighing receipt / acknowledgement of receipt |
| Recent glass wool pipe sections (asbestos-free) | Combustible construction waste | Incineration in a thermal recovery plant | Certified landfill voucher |
| Asbestos-containing plaster or cardboard insulation | Hazardous waste subject to notification | Dedicated inert-materials landfill | Asbestos waste tracking form |
According to art. 16 OLED, the client provides, on request, proof of compliant disposal after the end of the works if the quantity exceeds 200 m³ or if waste containing hazardous pollutants is to be expected. The heating installer must hand over to site management all the supporting documents: receipts for sorted skips, metal buy-back vouchers and tracking forms for special waste signed by the carrier and the receiving centre. Using the special-waste tracking system makes it possible to issue the official document bearing the appropriate waste codes. Without this duly initialled document, the company remains legally responsible for the polluting material in the event of illegal dumping or a clandestine disposal channel.
Technical segregation in the boiler room: burners, boiler bodies and insulation
Dismantling a thermal installation tolerates no mixed-waste skip. Art. 17 OLED requires that special waste be separated from other waste and disposed of separately, the remainder being sorted on the construction site. For the heating installer, the operation begins with the methodical disassembly of the heterogeneous sub-assemblies. An oil or gas burner is not a block of raw steel: it contains an electric motor, an ignition transformer, a photoelectric cell, an electronic safety control box and an oil pump still impregnated with hydrocarbons. This sub-assembly belongs to the electrical and electronic appliance channel for its controlled components, while its cast-aluminium body and its pipework go to metal recovery.
Dismantling the boiler requires fine sorting of the metals to guarantee their recovery and avoid rejection at the landfill. Grey cast-iron boiler bodies are cut up or unbolted after removal of the lacquered sheet-metal casings. The distribution pipework must have its clamps with elastomer lining removed before being bundled. The cold-worked copper of the hydraulic connections and the brass manifolds are set apart from the heavy scrap, because mixing greatly reduces the buy-back price of the materials. Stainless steel plate heat exchangers go into a separate bin, stripped of their insulating shells of expanded polyurethane or mineral wool.
| Item removed | Type of material | Packaging on site | Take-back channel |
|---|---|---|---|
| Cut-up boiler body | Grey cast iron / black steel | Heavy scrap skip | Recycling foundry / steelworks |
| Pipework and valves | Copper, brass, bronze | Separate pallet boxes | Non-ferrous metal dealer |
| Dismantled burner | Electronic waste and aluminium | Sealed film-wrapped pallet | SENS collection point / WEEE recycling |
| Asbestos-free insulation | Mineral wools (glass wool/rock wool) | Closed transparent bags | Type B controlled landfill |
| Plaster-type or suspect insulation | Special waste / potential asbestos | Approved labelled double bagging | Approved special waste channel |
Thermal insulation is a point requiring acute vigilance. Any plaster-type insulation around the bends of old pipework must be presumed to contain asbestos until proven otherwise by a prior diagnosis. Dismantling a suspect insulation without containment is prohibited. If the material is formally identified as recent mineral wool, it must be removed in closed, sealed bags to prevent fibres from becoming airborne in the boiler room and in occupied premises.
VeVA tracking forms and documentary compliance of the strip-out
The off-site removal of polluting materials is subject to rigorous digital traceability. Sludgy heating circuit water, loaded with corrosion inhibitors, biocides or degraded glycol, may not be discharged into the municipal sewer or into stormwater collectors. These effluents must be pumped directly into airtight drums or a recovery tank by a specialist company holding cantonal authorisations. The same applies to settling sludge extracted from the bottom of hot water cylinders or magnetic sludge traps.
As soon as the strip-out is complete, the foreman compiles the end-of-intervention file. It contains the weighing vouchers issued by the approved scrap dealer, the take-back receipts for electronic appliances, and certified copies of the tracking forms for special waste. Art. 16 OLED provides that the client provides, on request, proof of compliant disposal after the end of the works. The installer therefore passes this complete file to site management to release the payment claims associated with the dismantling item. Keeping a complete duplicate in the technical company's archives for five years protects the operator in the event of a subsequent inspection by the cantonal environmental services.
Handling sorting non-conformities and disposal blockages
During a boiler-room strip-out, malfunctions frequently occur in two forms: a skip rejected by the sorting centre because of prohibited mixing, or the unexpected discovery of a hazardous component during cutting. If a collector refuses a load of scrap because of mineral insulation stuck to the generators or fuel oil residues in a burner, the load returns to the construction site at the installer's expense. Art. 17 OLED provides that special waste is separated from other waste and disposed of separately. Faced with a rejection, any attempt at concealment worsens the financial loss and halts the construction site.
- Stopping work at the workstationSuspend cutting or loading as soon as a doubtful material comes to light, whether it is an unknown friable insulation, acid condensate or a pool of stagnant hydrocarbons at the bottom of the firebox.
- Isolation and containmentPlace the disputed fraction in a sealed containment tray for fluids or under a sealed tarpaulin for solids, away from the clean-metal skips and from escape routes.
- Notification and reassignment of the channelNotify site management and the client in writing of the nature of the waste. Order the appropriate regulatory containers and call on an approved disposal contractor holding a cantonal authorisation.
- Regularising the documentationDraw up the tracking form for special waste before any loading and keep the duplicate stamped by the carrier to close the strip-out file.
In the event of disagreement over the presence of polluting residues in a pipe or a boiler body, the company immediately provides the proof of complete draining and the itemised weighing vouchers. If a scrap skip has been downgraded on the grounds of mixed insulation, the installer demands a joint sorting on a platform rather than a global landfill disposal at his own expense. Keeping the tracking forms protects the heating engineer against any subsequent environmental liability on the remediated plot.
Frequently asked questions
What should be done if the heating network contains glycol water during the strip-out?
The water-glycol mixture must never reach the public sewer network or the clean-water drains. The installer pumps the circuit into sealed drums or transport tanks using a dedicated pump. These fluids are classified as special waste. They must be handed over to an authorised collector, accompanied by a specific tracking form. The disposal supporting documents are then passed to the client to certify compliant treatment.
Can an old oil burner be thrown directly into the scrap skip?
No, a complete burner is not ordinary metal waste. It contains electrical components, an ignition transformer, an oil pump loaded with hydrocarbons and sometimes asbestos-containing gaskets. The appliance must be dismantled: clean metals go to recovery, while the components soiled with hydrocarbons, the oil filter and the electronic circuits follow their respective special waste disposal channels with the corresponding take-back certificates.
How should old plaster insulation or pipe sections found on the pipes be handled?
Any plaster insulation or old pipe section is suspected of containing asbestos. Before any mechanical dismantling or cutting with a reciprocating saw, a diagnosis must confirm the absence of harmful fibres. If the material contains asbestos, only authorised specialists carry out containment and removal. If the insulation is modern mineral wool free of pollutants, it is bagged on site and placed in the combustible mineral waste channel or a suitable landfill.
Who bears the financial responsibility if a skip is downgraded at the sorting centre?
The company that filled the skip is responsible for its contents. If prohibited materials such as insulation, solvents or soiled rubble are tipped into it, the sorting centre applies the maximum downgrading rate for mixed unsorted waste, and may even charge manual sorting and analysis fees. To avoid any dispute, the foreman visually checks each skip before it is collected and keeps the countersigned weighing voucher.
Texts and standards cited
- OLED art. 17sorting of construction waste: special waste is separated from other waste and disposed of separately; the remainder is sorted on the construction site
