Key takeaways
- The usable volume compensates for the expansion of the water between filling and the maximum operating temperature.
- The initial pre-charge pressure is adjusted strictly according to the static height of the highest point of the installation.
- The safety valve is installed without any isolation device and discharges by gravity through a visible funnel at floor level.
- The annual check of the gas cushion requires hydraulic isolation and complete draining of the vessel before measurement.
Calculating the expansion volume and setting the initial pre-charge pressure
In a boiler room, water undergoes a change in volume proportional to the rise in temperature. Without a suitable compensating device, the incompressibility of the fluid causes a sudden pressure rise that reaches the opening threshold of the safety valve. Conversely, during cooling, the contraction of the water creates a negative pressure, promoting air intake at the automatic air vents, cavitation of the circulators and sludge formation through oxygenation of the metals.
- Calculated expansion volume
- Additional volume of fluid produced by the rise in temperature of the installation, corresponding to the product of the total water content of the network and the maximum permissible expansion coefficient.
The calculation begins with an accurate survey of the total water content of the system. In new installations with a heat pump and underfloor heating, the specific volume is often small, but the presence of a heat accumulator or a decoupling buffer tank drastically increases the mass of water. In renovations with cast-iron radiators or large-diameter steel columns, the circuit capacity frequently exceeds ten to fifteen litres per kilowatt of installed output.
| Temperature regime | Mean temperature (°C) | Expansion rate e (%) | Typical application |
|---|---|---|---|
| 35 / 28 °C | 31.5 | 0.60 | Low-temperature heat pump underfloor heating |
| 55 / 45 °C | 50.0 | 1.21 | Low-temperature radiators and fan coil units |
| 70 / 55 °C | 62.5 | 1.85 | Traditional radiator network on a pellet boiler |
| 80 / 60 °C | 70.0 | 2.28 | High-temperature network or direct district heating |
The pure expansion volume is increased by a usable water reserve, intended to compensate for micro-leaks and the initial purging of dissolved gases. This reserve equals 0.5 % of the total volume, with an absolute minimum of 3 litres. The initial cold pre-charge pressure of the nitrogen cushion must be set to the static height of the installation, plus 0.2 to 0.3 bar to keep the highest point under positive pressure. For a three-storey building with 9 metres between the vessel in the basement and the highest radiator, the static height represents 0.9 bar, requiring a cold pre-charge pressure of 1.2 bar.
Connecting the safety valve and carrying out the five-minute annual check
The safety valve is the last line of defence against destructive overpressure in the generator or the pipework. It is mounted directly on the flow or return of the boiler or heat pump, on a section free of any isolation device, non-return valve or filter. The diameter of the discharge pipe must under no circumstances be smaller than the nominal outlet diameter of the valve. Its route must be as direct as possible, laid with a continuous downward slope to a drain funnel connected to the gravity drainage of the boiler room.
The recurring mistake on construction sites is measuring the pressure of the expansion vessel while the water chamber is still under the hydraulic pressure of the network. The pneumatic pressure gauge connected to the Schrader valve then simply shows the pressure of the heating circuit, masking the total loss of gas. To ensure compliant work, installing a dedicated isolation valve with a sealed cap and an integrated drain cock upstream of each vessel is essential.
- Isolate the hydraulic connectionClose the capped stop valve located on the inlet connection of the expansion vessel to separate it from the pressurised circuit.
- Release the water pressureOpen the drain cock of the maintenance fitting into a bucket until the flow stops completely, to bring the water chamber to atmospheric pressure.
- Check the gas cushionConnect a calibrated test pressure gauge to the Schrader valve and measure the pre-charge pressure of the membrane.
- Adjust the nitrogen chargeTop up the pressure with a pump or a cylinder of dry nitrogen to reach the nominal value calculated according to the static height.
- Return the vessel to serviceClose the drain cock, slowly reopen the main isolation valve and seal its protective cap with a lead seal or a tamper-evident tie.
Calculating the expansion volume and setting the cold pre-charge pressure
In a closed-circuit central heating installation, water expands as its temperature rises. As water is practically incompressible, any increase in volume that is not absorbed results in a pressure peak that stresses the components and leads to the opening of the valve. Conversely, during cooling, the contraction of the fluid creates a negative pressure responsible for air intake at the automatic air vents, causing circulation noise and accelerated corrosion of the metal emitters. The choice of a gas-pressurised diaphragm expansion vessel is therefore not made by guesswork or on the boiler output alone.
- Calculated expansion volume (Ve)
- Additional volume of water generated by the rise in temperature of the whole heat-transfer fluid from the filling temperature to the maximum flow temperature, increased by a minimum water reserve intended to compensate for micro-leaks in the circuit during the heating cycle.
Sizing is based on the total water volume of the installation (boiler or heat pump, distribution network, buffer tanks and emitters). According to the recognised rules of the trade applied in French-speaking Switzerland and standard SIA 384/1, an expansion coefficient depending on the temperature regime is applied. For a conventional radiator regime of 70/50 °C, the water expands by about 2.28 %; for low-temperature underfloor heating at 35/28 °C, this value falls to 0.65 %. To this net expansion volume is added the usable water reserve in the vessel, which represents at least 0.5 % of the total volume of the installation, with a minimum of 3 litres to avoid any loss of prime of the membrane at rest.
The cold pre-charge pressure of the nitrogen cushion, denoted P0, directly determines the usable capacity of the vessel. It must correspond to the static height of the installation (expressed in metres of water column divided by ten to obtain bar), plus a minimum overpressure of 0.2 to 0.5 bar to guarantee continuous positive pressure at the highest point of the building, in particular to avoid cavitation of the circulator. A vessel delivered from the factory with a pre-pressure of 1.5 bar and installed in a single-storey house without adjustment will have its membrane needlessly squashed by the nitrogen, reducing the available water volume and causing pressure oscillations from the first heating-up.
| Type of emitter | Mean regime (°C) | Water expansion (%) | Static pressure (m WC) | Recommended nominal volume |
|---|---|---|---|---|
| Underfloor heating (PEX) | 35 / 28 | 0.65 % | 8 m (0.8 bar) | ~ 5 to 7 % of the total water volume |
| Low-temperature radiators | 50 / 40 | 1.21 % | 10 m (1.0 bar) | ~ 8 to 10 % of the total water volume |
| High-temperature radiators | 75 / 65 | 2.60 % | 12 m (1.2 bar) | ~ 12 to 15 % of the total water volume |
| Mixed network with buffer tank | Variable | 2.20 % (average) | 15 m (1.5 bar) | Detailed calculation based on actual stored volume |
Connecting the valve, free discharge and annual check procedure
The safety valve is the last line of defence against bursting of the heating elements or plate heat exchangers. In residential buildings, it is commonly set at 3.0 bar. For the vessel to absorb the entire expansion without the valve opening, the final pressure of the network at the end of the heating cycle must remain at least 0.5 bar below the valve opening pressure. When this margin is squeezed by a badly calculated vessel, the valve regularly spits out a few decilitres during cold peaks, prompting the operator to top up with cold water and reintroduce limescale and dissolved oxygen into the loop.
- Hydraulically isolate the vesselClose the isolation valve with a padlockable or sealable cap fitted on the water inlet connection of the vessel. Never remove the vessel without this dedicated stop device.
- Depressurise the water chamberOpen the purge or drain cock located between the isolation valve and the vessel flange. Let the water run into a bucket until the residual hydraulic pressure drops to exactly zero bar on the purge pressure gauge.
- Measure and readjust the gas pressureUnscrew the cap of the Schrader valve located on the dome of the vessel. Connect a calibrated tyre-type test pressure gauge. If the measured nitrogen pressure is lower than the set value P0, top up using a cylinder of dry nitrogen or a hand pump fitted with a desiccant filter.
- Diagnose the condition of the bladderIf water escapes from the charging valve as soon as the valve core is pressed or when the quick coupling is connected, the rubber membrane is punctured. The vessel must be replaced immediately or fitted with a compliant replacement bladder.
- Return to service and top-up fillingClose the drain cock, reopen the capped valve and lock its control. Adjust the overall filling pressure of the installation on the cold hydraulic circuit to P0 + 0.3 bar to set the initial water reserve.
When carrying out maintenance work, the installer makes sure to record the pre-charge pressure P0 measured and adjusted on a self-adhesive label affixed to the body of the vessel. Meticulous compliance with this procedure ensures compliance with the general duties of care provided for in the Code of Obligations (CO) for the performance of a technical mandate or a contract for work.
Emergency troubleshooting and restoring a faulty expansion vessel
On a heating installation subject to sudden pressure variations, diagnosis begins by observing the pressure gauge between the complete shutdown of the burners or compressors and their maximum operation. A needle that swings between 0.8 bar when cold and 3.0 bar when hot invariably indicates an ineffective expansion volume. Two causes predominate: a perforated membrane or a total loss of nitrogen back-pressure through the valve core.
- Isolating and depressurising the vesselClose the dedicated isolation valve fitted with its locking cap. Open the intermediate drain cock located between this valve and the vessel to relieve the hydraulic pressure on the water side. Let it run until dripping stops completely.
- Diagnosing the membrane at the valveUnscrew the protective cap of the Schrader-type valve. Briefly press the central pin. Liquid water coming out proves internal rupture of the bladder or membrane: the vessel must be replaced. Air coming out or a total absence of airflow indicates simple loss of pressure.
- Adjusting the gas cushionWith the water drain left open to the atmosphere, connect a pump with a calibrated pressure gauge to the valve. Charge with nitrogen or dry air up to the static pressure set value plus 0.2 bar for the initial water reserve. Close the drain, reopen the isolation valve, then lock its handwheel.
If the nominal expansion volume proves insufficient following an extension of the network or the addition of a heat accumulator that was not taken into account, a second vessel should be added in parallel rather than raising the valve setting. In accordance with the Code of Obligations (CO), the installer reports any mismatch between the connected thermal output and the safety devices in place in order to guarantee the durability of the work.
Frequently asked questions
Why does the valve mainly spit in the depths of winter?
In the middle of winter, the distribution circuit operates at its maximum flow temperature, which produces the greatest volume expansion of the mass of water. If the vessel is undersized or if its nitrogen chamber has lost its cold pre-charge pressure, the calculated expansion volume can no longer be absorbed. The excess volume then raises the hydraulic pressure up to the setting of the safety valve, which discharges the fluid.
How can a torn vessel membrane be detected without dismantling the whole network?
The test is carried out in the boiler room in a few seconds at the charging valve of the vessel. After isolating the vessel via its sealed-cap valve and draining its water-side connection, briefly press the pin of the Schrader valve. If heating water escapes through the valve reserved for the gas, the elastomer membrane is punctured. The vessel is waterlogged and must be replaced.
Which fluid should be used to adjust the cold pre-charge pressure?
Dry nitrogen is the recommended gas for pressurising diaphragm vessels in closed circuits. Less prone to migration through the elastomer walls than the oxygen in ambient air, nitrogen also eliminates any risk of internal oxidation of the steel vessel. If troubleshooting without a nitrogen cylinder on site, a dry-air compressor fitted with an oil separator is an acceptable temporary solution until the next annual check.
Where must the safety valve discharge imperatively end?
The discharge pipe of the safety valve must end above a drain funnel with a visible air gap, connected to the drain of the boiler room. It must have no isolation device and no reduction in diameter compared with the outlet orifice of the valve, and its continuous slope must prevent any water from being retained. The discharge area must remain visible so that leaks can be detected immediately without risk of burns.
