Skip to content
Website
🧱 CFC 241Emitters: underfloor heating and radiatorsChapter 7 of 10 in the section

Thermostatic valves: presetting, head position and actual use

By the end of this chapter, you will be able to size and adjust the hydraulic presetting of the valve body according to the distribution calculation. You will be able to position the thermostatic head horizontally to avoid false temperature readings, lock the mechanical limiting stops and give the occupant the two real operating instructions.

Key takeaways

  • The presetting built into the body balances the mass flow rate without depending on the lockshield (balancing) fitting.
  • A thermostatic head mounted vertically or enclosed under a shelf records a distorted temperature.
  • A remote sensor is required whenever a thick curtain or a cover insulates the sensing element.
  • The limiting pins prevent overheating while preserving the frost protection function.

Adjust the body presetting and locate the thermostatic head outside enclosed zones

The thermostatic valve provides terminal control room by room, but it does not replace hydraulic balancing of the network. When the valve body has no presetting or is left at its factory maximum opening position, the radiators closest to the circulator saturate the network at the expense of the remote loops. The built-in mechanical presetting adjusts the opening of the internal orifice to the nominal flow rate required for the calculated output of the emitter, under the setpoint differential pressure. This setting is made directly on the graduated ring of the body after removing the protective cap, using the dedicated key or by turning the indexed sleeve, without draining the heating system.

Indicative body presetting positions according to nominal mass flow rate
Nominal water flow range (l/h)Usual presetting markTarget differential pressure drop (kPa)
15 to 451 to 210
50 to 903 to 410
95 to 1605 to 610
170 to 2807 or white dot10

The orientation of the thermostatic head determines the validity of the room temperature measurement. The internal bellows, containing an expandable liquid or wax, reacts to the convective air flow washing over the perforated housing. If the head is screwed vertically upwards onto a standard angle body, the rising heat given off by the pipework and the steel connection directly heats the sensing bulb. The thermostatic element expands prematurely and cuts off the hot water circulation while the room air is still cold. Installation is always carried out with the axis of the head horizontal, parallel or perpendicular to the heating plane depending on the shape of the body.

Lock the stop ranges and pass the usage instructions on to the occupant

  1. Checking the operating stemPress the axial metal stem of the stuffing box with a flat tool handle to check its elastic travel. Never strike the stem or try to pull it out with pliers, as this risks tearing the O-ring.
  2. Fitting and tightening the headOpen the head to the maximum graduation to retract the pin. Push the head onto the M30 thread or the snap-on connection of the body, then tighten the fixing ring by hand before locking without excessive force.
  3. Fitting the stop clipsInsert the limiting lugs or pins hidden under the collar to prevent any mechanical overrun of mark 3 (corresponding to approximately 20 °C) in living rooms.

The snowflake mark represents frost protection. This setting keeps the valve closed as long as the immediate ambient temperature remains above approximately 6 to 8 °C, then allows a slight opening as soon as the temperature drops. The frequent error on the construction site is to block the valve completely with a solid site plug to stop the noise: the body can then no longer react, and frost destroys the radiator during prolonged winter ventilation. The low limit set with the built-in stops guarantees that the user can never turn the head below the snowflake.

Explaining this physical principle defuses most complaints about a radiator that is lukewarm in its lower part. The customer thus understands that a heating element that modulates its hot water flow performs its local control function perfectly, without needing repeated adjustments during the day.

Diagnosing hot air pockets and fitting remote devices

When a radiator is installed in a masonry recess, under a deep sill shelf or hidden by thick curtains, natural convective circulation is interrupted. The standard thermostatic head with integrated liquid or wax bulb ends up confined in a pocket of thermal stagnation. In this closed zone, the air heated by the top manifold and the radiator body quickly reaches 24 °C to 26 °C, while the actual room temperature remains cold, often below 18 °C. The expansion of the thermostatic element causes the valve to close early, leading to immediate complaints about insufficient heating.

To remedy this without altering the interior layout imposed by the client, the installer replaces the compact head with a head with a remote sensor or with a remote-control assembly. The remote sensor contains all of the expandable fluid and communicates with the receiving bellows through a copper capillary tube of a common length of 2 metres. The capillary must be unrolled without kinks or crushing along the skirting board or hidden behind the console foot, then fixed mechanically to the vertical wall.

Behaviour of the control depending on the mounting environment of the thermostatic head
Emitter configurationMeasurement deviation recordedConsequence for the circuitCorrective action required
Front unobstructed, head horizontal and freeLess than 0.5 K from room temperatureStable proportional control, water flow adjustedKeep the standard head mounted horizontally
Lined curtain hanging in front of the radiatorLocal overheating of 3 K to 5 K under the fabricPremature closing of the valve, room cold below 19 °CFit a head with a remote sensor clipped onto the side wall
Narrow masonry recess with continuous shelfTrapped hot pocket, deviation greater than 4 KConstant hunting of the bulb, return water disturbedFit a remote wall-mounted thermostatic control
Head oriented vertically upwardsMeasurement distorted by 2 K by the supply pipeChronic under-flow, poor stratification of the roomReplace the body or fit a 90° adapter facing forwards

Recessing a radiator also reduces its overall heat transfer coefficient to the room. The foreman adjusts the presetting of the valve body to restore the mass flow rate calculated according to the heat load of the room. On a valve body with tool-free built-in presetting or with a micrometric ring, the kv flow value is recalculated to compensate for the loss of convective output, generally estimated at between 10% and 15% when the emitter is enclosed under a grille or a shelf.

Limiting the ranges, mechanical pinning and handover to the user

In communal installations, drift of the setpoints through disorderly handling by occupants causes hydraulic imbalances in the riser and massive overconsumption. Industrial thermostatic heads include housings for clips or metal pins hidden under the adjusting ring. These mechanical stops, invisible from outside, make it possible to lock the setpoint at a fixed value or to restrict the rotation travel to a strict range.

The low stop is generally set to prevent the valve from closing completely. In communal housing with individual metering, dropping below 16 °C generates passive heat transfers from adjoining neighbouring dwellings. Locking the low limit on the snowflake symbol or on graduation 2 prevents the heating element from freezing if a window is left ajar for a long time, while also avoiding the push stem remaining jammed at the bottom of the seat for a long time during the summer. The high stop is set mechanically on mark 3, corresponding to a setpoint temperature between 20 °C and 20.5 °C.

  1. Unlocking the limiting ringRemove the cover of the thermostatic head with an insulated flat screwdriver to access the holes for the peripheral pins.
  2. Inserting the stop clipsPosition the first metal lug at mark 2 to block the setting from dropping below 16 °C. Engage the second lug at mark 3 to prevent exceeding 20 °C.
  3. Checking the useful travelCarry out a full rotation from one stop to the other, visually checking the free movement of the drive sleeve on the body.
  4. Refitting the trimSnap the protective ring firmly into place so that the lugs cannot be reached for tampering without specific tools.

Passing the instructions on to the end user determines the overall performance of the heat distribution. At the acceptance of the work, the installer gives the technical explanation in two simple, imperative sentences: "The thermostatic valve is not a water tap: setting it to 5 does not heat the room faster, it simply delays the closing of the radiator, which will overheat needlessly. Leave the head on mark 3 permanently and ventilate your rooms widely for five minutes without ever touching the mechanical wheel."

Resolving thermal disputes and correcting positioning errors

When a room fails to reach comfort temperature or suffers intermittent surges of heat, the installer first checks the immediate surroundings of the thermostatic valve. The recurring error on the construction site is the confinement of the head under a masonry window shelf, behind a decorative radiator cover or trapped in sealed blackout curtains. In this closed air pocket, the expandable sensor measures only the overheated air stagnating against the pipework. The device shuts off the hot water supply even though the room remains cold and uncomfortable for the user.

  1. Diagnosing flow and presettingRemove the thermostatic head and examine the numerical mark of the built-in plug. If the presetting value has been selected too low compared with the thermal calculation data, the hot water flow is insufficient to meet the nominal output of the heating element. Readjust the notched ring with the dedicated key according to the manufacturer's chart.
  2. Replacing with a remote sensorWhen curtains or furniture cannot be moved, remove the standard head and fit a model with a flexible copper or reinforced plastic capillary. Fix the measuring sensor on an interior wall at a height of one metre fifty, away from cold draughts and stray heat sources.
  3. Locking the setpoint rangesPush the plastic pins or clips into the guide slots of the head to set the travel limit. Set the lower stop on the snowflake symbol to prevent any freezing of the pipes during absence, and fix the upper stop on position three, corresponding to twenty degrees.

If the final customer refuses to clear the emitter or to allow a wall sensor to be fitted, the installer records these reservations in writing in accordance with the general requirements of standard SIA 118. The job always ends with the handover of a brief leaflet recalling that the thermostatic valve is neither a manual mixer nor an on/off tap.

Frequently asked questions

Why does the radiator whistle after the valve presetting has been adjusted?

A high-pitched whistle indicates an excessive flow velocity at the valve seat, caused by too high a differential pressure. This frequently happens when the Kv presetting is strongly throttled to restrict the flow or when the circulation pump runs at fixed speed without a relief valve. To eliminate the noise, adapt the curve of the electronic circulator and make sure that the flow and return directions were not reversed during connection.

Should the thermostatic head be oriented horizontally or upwards?

The thermostatic head must always be fitted horizontally, oriented towards the inside of the heated space. Mounted vertically upwards, the heat-sensitive capsule directly receives the column of convective heat rising from the supply pipe and the cast-iron or steel body. The sensor then overestimates the room temperature by at least two to three degrees, which causes the valve to close prematurely and leaves the room permanently underheated.

How do you explain the operation of the valve to the occupant in two sentences?

The instructions to the user come down to two simple and practical principles. First, set the ring on graduation three to automatically maintain twenty degrees; do not go up to mark five to heat faster, because the radiator will not deliver any hotter. Second, never cover the head with a heavy curtain or a piece of furniture, otherwise you will turn your room into an icebox by fooling the sensor's measurement.

What are the metal pins or clips built into the head for?

These mechanical locking parts are used to lock the travel of the adjusting wheel to prevent any wrong handling by the occupant, particularly in rented housing or schools. They make it possible to set a narrow range, for example between eighteen and twenty degrees, or to fix a threshold that cannot be crossed. The low stop guarantees that the frost protection position is maintained, while the high stop prevents needless energy overconsumption.

Texts and standards cited

  • norme SIA 118General conditions for the execution of construction work

In the same section