Key takeaways
- The volumetric flow rate follows directly from the required thermal output and the chosen temperature difference.
- A linear pressure drop of between fifty and one hundred and fifty pascals per metre ensures balance.
- The flow velocity in rest rooms must not exceed zero point five metres per second.
- Undersizing a pipe overloads the circulator and causes permanent whistling at the thermostatic valves.
Calibrating the mass flow rate and limiting the linear pressure drop
The hydraulic sizing of a heating distribution system starts with converting the thermal load into a water flow rate. The fundamental relationship links the room's output to the density of the fluid, its heat capacity and the temperature difference between flow and return. In modern installations fed by heat pumps, the water temperature regimes are narrow: a difference of five to seven kelvins requires flow rates two to three times higher than on older boilers operating with a twenty-kelvin drop. If the fitter keeps the old diameters during a refurbishment, or reduces the cross-section to make routing through a shaft easier, the required volume of water no longer passes without generating a prohibitive pressure drop.
The first critical threshold concerns the unit linear pressure drop, denoted R and expressed in pascals per metre. On main sections and risers, the target value lies between 50 and 150 Pa/m. Tolerating 200 Pa/m remains admissible on a short section in a basement or boiler room, but exceeding this value over a whole loop multiplies the required pump head. The circulator must then run at full power 24 hours a day to overcome this internal resistance, which causes a measurable excess electricity consumption throughout the heating season.
| Section allocation | Pressure drop R (Pa/m) | Maximum velocity (m/s) | Main risk in case of error |
|---|---|---|---|
| Sensitive rooms (bedrooms) | 40 to 80 | 0.20 to 0.40 | Friction noise and night-time whistling |
| Floor distribution and daytime rooms | 60 to 120 | 0.40 to 0.60 | Sound transmission through wall clamps |
| Risers and service shafts | 80 to 150 | 0.60 to 0.80 | Hydraulic imbalance of the upper floors |
| Manifolds and connections in the boiler room | 100 to 200 | 0.80 to 1.20 | Excess electricity consumption of the circulator |
Limiting the maximum velocity to eliminate noise in sensitive rooms
The velocity of the heat-transfer fluid is the second unavoidable limit of sizing. Even if the pump delivers the pressure needed to overcome a restricted network, the acceleration of the water in a tube of too small a diameter produces severe turbulent flow. As soon as the water passes a sharp bend, a branch tee or a valve restriction at excessive velocity, it generates eddies and local pressure variations. These phenomena turn the pipework into a mechanical loudspeaker whose vibrations propagate directly into the masonry through the fixing clamps.
- Determine the thermal load of the sectionDetermine the sum of the outputs of the emitters connected downstream of the section to be sized, including the actual heat losses according to the thermal calculations.
- Calculate the flow rate according to the temperature regimeApply the nominal temperature drop chosen for the thermal system to obtain the mass flow rate and then the corresponding hourly volume.
- Select the nominal internal diameterConsult the pressure drop chart specific to the chosen material to select the diameter that keeps the velocity below the acoustic threshold of the room crossed.
- Check compatibility with the shut-off devicesMake sure that the diameters of the zone valves, flow meters and check valves do not create a disproportionate local restriction.
In contractual terms, the contractor carries out the work in accordance with established professional rules, in line with the principle set out in art. 364 CO. A network whose hydraulic noise exceeds the comfort tolerances accepted for housing makes the work defective and exposes the installer to heavy remedial works. If the planner or the client demands cross-sections that are too small in order to conceal the pipes in inadequate recesses, the construction site foreman must immediately report the risk of noise nuisance in writing before starting installation.
Impact of undersizing: excessive pressure drops and additional operating costs
On a central heating construction site, arbitrarily reducing the nominal diameter of a pipe by one size to make routing through a floor opening easier or to save on fittings causes major problems. Sizing steel, copper or multilayer pipes does not merely mean conveying a sufficient volumetric flow: it requires the simultaneous observance of three mandatory physical thresholds, namely the maximum flow velocity, the permissible pressure drop and the overall acoustic emission. When an installer lays a tube that is too narrow, the average velocity of the fluid must increase to supply the thermal output demanded by the emitters. This acceleration causes a quadratic increase in hydraulic friction, which disturbs the authority of the control devices and complicates the hydraulic balancing of the secondary branches.
This additional mechanical resistance heavily penalises the pumping unit. The electrical power absorbed by a modern high-efficiency circulator is proportional to the product of the flow rate and the total pressure drop of the most disadvantaged part of the network. Doubling or tripling the linear resistance forces the technician to set the pump to a much steeper head curve. Over a typical heating season of 3500 to 4500 hours in French-speaking Switzerland, this excess consumption translates into a recurring electricity cost for the operator. In addition, this excessive friction generates too high a differential pressure upstream of the thermostatic valve bodies. As soon as a valve plug starts to regulate by closing the passage, this differential causes turbulence that produces audible whistling resonating in the radiators.
| Useful internal diameter | Output carried (kW) | Volumetric flow rate (l/h) | Fluid velocity (m/s) | Linear drop R (Pa/m) | Observed acoustic behaviour |
|---|---|---|---|---|---|
| DN 12 (tube 14x1) | 5.0 kW | 430 l/h | 0.95 m/s | 340 Pa/m | Unacceptable in sleeping areas; whistling at the valves |
| DN 15 (tube 18x1) | 5.0 kW | 430 l/h | 0.53 m/s | 85 Pa/m | Optimal for final distribution in housing |
| DN 15 (tube 18x1) | 10.0 kW | 860 l/h | 1.07 m/s | 310 Pa/m | Audible turbulence at the radiator connections |
| DN 20 (tube 22x1) | 10.0 kW | 860 l/h | 0.68 m/s | 105 Pa/m | Compliant for general distribution and suspended ceilings |
| DN 25 (tube 28x1.5) | 10.0 kW | 860 l/h | 0.44 m/s | 35 Pa/m | Totally silent; recommended for risers |
Execution rules for sensitive rooms and acoustic control
Occupant comfort demands absolute rigour when routing pipes through sensitive rooms such as bedrooms, children's rooms or rest areas. Standard SIA 384/1 governs the rules of the art for hot-water heating installations by setting clear limits to prevent noise nuisance. For the heating installer, the flow noise in sensitive rooms comes both from disturbances within the fluid and from vibrations transmitted to the masonry by direct contact. The maximum flow velocity must therefore be kept between 0.3 and 0.5 m/s in the sections located in these rooms, whereas risers in closed service shafts may allow between 0.8 and 1.0 m/s provided effective decoupling is ensured.
- Calculating the volumetric flow rate per branchDetermine the exact thermal load of the group of connected emitters and convert the output into a water flow rate according to the operating regime (delta T of 5 to 10 K for a heat pump). Never artificially reduce the flow rate to justify a smaller tube.
- Selecting the diameter according to the maximum velocityConsult the pressure drop chart specific to the installed material (threaded steel, copper or multilayer system). Choose a cross-section ensuring a velocity below 0.5 m/s for connections in bedrooms and below 0.8 m/s for risers in service shafts.
- Checking the permissible pressure dropMake sure that the linear drop remains between 80 and 150 Pa/m on the longest route. For an extensive network, increase by one nominal size to avoid exceeding the pump head and to limit excessive authority over the valves.
- Acoustic decoupling of the supportsFix the pipework with sound-insulating clamps fitted with an EPDM rubber lining. Fit split resilient sleeves at floor and partition penetrations to avoid any rigid acoustic bridge between the metal tube and the concrete slab.
Remedies and corrective measures in the case of proven undersizing
When commissioning checks reveal velocities above the acoustic criteria permitted under standard SIA 181 or a critical lack of flow due to non-compliance with standard SIA 384/1, the heating engineer must act methodically. The dispute often arises during cold spells, when the control system drives the valves to full opening without managing to balance the network.
- Measure the differential pressuresConnect an electronic differential pressure gauge to the balancing valves of the circuit in question in order to objectively establish the actual pressure drop and to check whether the pump head matches the initial calculations.
- Adjust the operating temperature differenceIncrease the thermal regime by slightly raising the flow temperature to widen the temperature spread (for example from 10 K to 15 K). This measure lowers the required mass flow rate and reduces the velocity in the tube.
- Install differential pressure regulatorsInsert dynamic balancing valves at the foot of the risers serving the sensitive rooms to limit the available pressure to below 15 kPa and eliminate flow noise at the terminal valves.
- Replace the bottleneck sectionsIf the residual pressure drops paralyse the network, identify by measurement the undersized fittings or manifolds in the basement and replace these lengths surgically with a suitable nominal diameter.
In legal terms, if the diameters installed comply with the execution drawings supplied by the engineer but prove unsuitable for use, the installer reports the problem under art. 365 CO para. 3 in order to release himself from liability for design defects. If the error results from installing narrower pipes than prescribed, the client may demand that the work be remedied on the basis of CO.
Frequently asked questions
How can a persistent whistle on a thermostatic valve in a bedroom be calmed?
The whistling comes from too high a differential pressure at the valve plug, often exceeding 15 to 20 kPa because of a restricted network. First check the rotation speed of the circulator and switch to variable differential pressure control. If the noise persists, adding a differential pressure regulating valve at the foot of the riser absorbs the excess hydraulic load generated by the building's undersized pipes.
Why does increasing the temperature difference compensate for a pipe that is too narrow?
The thermal output distributed depends directly on the product of the mass flow rate and the temperature difference between flow and return. If the existing pipework limits the flow rate because of too small an internal cross-section, moving for example from a temperature drop of 10 K to 15 K reduces the volume of water to be circulated by a third. The velocity drops proportionally, eliminating the noise nuisance.
What maximum flow velocity should be used to avoid noise in dwellings?
Standard SIA 384/1 and the rules of the art recommend limiting the flow velocity to between 0.2 m/s and 0.5 m/s in internal branches and in pipes crossing sensitive rooms such as bedrooms. In risers in service shafts, the value should not exceed 0.8 to 1.0 m/s in order to meet the strict acoustic protection requirements set by standard SIA 181.
What should be done if the execution drawings specify a manifestly insufficient diameter?
The installer has a duty to warn the site management in writing before carrying out the installation. He provides a brief calculation note demonstrating that the required flow rate will result in excessive velocity and a linear pressure drop exceeding the permissible limits of standard SIA 384/1. This formal notice protects his rights by demonstrating the absence of fault in the execution.
Texts and standards cited
- SIA 384/1Heating installations in buildings - Distribution and control systems
- SIA 181Noise protection in buildings
- CO art. 365Defective material and ground: contractor's duty to notify the client
- COClient's rights in the event of defects in the work
