Skip to content
Website
🧱 CFC 241Hydraulic distribution and balancingChapter 5 of 10 in the section

Setting the circulator: curve, differential pressure and power consumption

This chapter gives you the method for configuring a high-efficiency heating circulator without relying on the factory setting. You will be able to select the curve suited to the network, set the operating point to the actual calculated flow rate, eliminate circulation noise at thermostatic valves and halve the electrical power absorbed.

Key takeaways

  • The variable differential pressure mode suits radiators fitted with thermostatic valve bodies.
  • The constant differential pressure mode remains the rule on underfloor heating manifolds.
  • Excessive differential pressure causes acoustic whistling as soon as the taps are partially closed.
  • Fine adjustment of the pump head immediately reduces the electrical consumption shown in watts.

Distinguishing constant and proportional pressure to control the network

When delivered to the construction site, most modern electronic circulators are factory-programmed to an automatic mode or to a very high maximum proportional-pressure curve. In an installation fitted with heating elements with thermostatic valves, this manufacturer pre-setting almost systematically leads to an overestimated operating point. As soon as solar or internal gains appear, the thermostatic heads gradually close the fluid passage. If the pump maintains an unsuitable pressure setpoint, the residual pressure drop is concentrated on the few valves left slightly open. The fluid accelerates sharply there, causing continuous whistling and very unpleasant flutter noises for the building's occupants.

Variable differential pressure (Δp-v)
Control mode in which the pump head supplied by the circulator decreases linearly as the flow rate is reduced, compensating for the drop in pressure losses distributed in the distribution risers.

For radiator networks, the variable differential pressure curve is the absolute reference. When the overall flow rate drops because valves are closing, the circulator reduces its rotation speed and lowers its pump head by half between nominal flow and zero flow. This pressure reduction prevents local overpressures at the valve plugs. The installer thus protects the installation against parasitic noise while stabilising the authority of the control devices on each heating element.

Constant differential pressure (Δp-c)
Control mode in which the circulator adjusts its speed to maintain a strictly identical pump head, whatever the water flow rate demanded by the installation.

Conversely, underfloor heating circuits connected to manifolds with variable flow require a constant differential pressure curve. The main pressure losses lie in the pipe loops embedded in the screed and remain stable for each individual circuit when its thermal actuator opens. If the pump reduced its pump head when certain zones close, the coils still active would suffer an unintended drop in flow, causing an immediate thermal imbalance and cold rooms.

Setting the actual operating point and checking the power absorbed

The actual operating point of a heat distribution pump results from the exact intersection between the characteristic curve selected on the circulator and the hydraulic resistance curve of the pipework network. To fix this point rigorously during commissioning, the foreman first calculates the overall volume flow rate of the loop by dividing the nominal power to be transmitted by the density of water, its specific heat and the design temperature difference, generally set at twenty kelvins on traditional radiators or five to seven kelvins on a low-temperature underfloor system.

  1. Calculate the setpoint volume flow rateMultiply the total output of the group's emitters by 0.86, then divide this product by the design thermal regime (ΔT) to obtain the required cubic metres per hour.
  2. Determine the required pump headAdd up the linear pressure losses of the most unfavourable circuit, the boiler-room singularities and the minimum authority required on the terminal control valve, expressed in metres of water column.
  3. Select the setpoint on the interfaceSet the circulator display to the corresponding mode (Δp-v or Δp-c) and adjust the setpoint value in metres to intercept the calculated flow rate on the unit's diagram.
  4. Check the displayed electrical powerRead the instantaneous absorbed power in watts shown by the circulator's built-in meter and compare this value with the hydraulic design forecasts.
Choice of control mode according to the characteristics of the hydraulic circuit
Type of heat emittersTerminal control devicesRecommended pressure modeConsequence of a wrong choice
Two-pipe radiatorsThermostatic valvesProportional pressure (Δp-v)Whistling at valves, excess electrical consumption
Underfloor heatingElectrothermal actuatorsConstant pressure (Δp-c)Insufficient flow in the remaining loops, cold rooms
Heat pump exchanger coilModulating control valveConstant pressure (Δp-c)Unstable compressor operating point
Old single-pipe networkManual valves without shut-offFixed constant speed (c1, c2, c3)Erratic temperature fluctuations between radiators

Direct measurement of instantaneous electrical consumption is the best indicator of the accuracy of the setting. A circulator left on its maximum factory curve commonly absorbs between forty and seventy watts in steady state for a standard house. As soon as the suitable proportional curve is activated with a pump head adjusted to two and a half or three metres of water column, the absorbed power immediately drops to between twelve and eighteen watts. This reduction divides the electrical power demand by three while avoiding premature mechanical wear of the seal and the rotor bearings.

Selecting the curve according to the heating elements and neutralising whistling

As delivered from the factory, an electronic wet-rotor circulator is frequently set to a fixed curve at maximum flow or to an uncalibrated generic automatic mode. This default choice compensates for initial balancing defects but generates immediate overpressure in the distribution network. As soon as the ambient temperature rises in the rooms, the thermostatic valves begin their closing stroke. The restriction of the cross-section at the valve seats increases the overall hydraulic resistance. If the pump maintains an excessively high constant pressure or a fixed speed, the remaining pump head is transferred directly to the terminal devices that are regulating.

The throttling phenomenon appears as soon as the differential pressure across a valve exceeds the critical threshold of 15 to 20 kPa. The water accelerates locally through the narrow orifice formed by the plug, creating noisy turbulence transmitted to the radiators by metal conduction. In networks fitted with heating elements with thermostatic valves, the installer must switch the circulator to a variable differential pressure curve (denoted Delta p-v). In this mode, the pump automatically lowers its pump head as the flow decreases in the risers. The pressure across the valves thus remains below the critical acoustic limit, even in part-load operation with 80% of the valves closed.

Checking the absorbed power and validating the operating point

Setting the pump does not stop at choosing the Delta p-v or Delta p-c profile: it requires defining the setpoint head (H) corresponding to the design flow rate. Reading the instantaneous electrical consumption directly in watts on the circulator display gives an immediate indicator of the mechanical effort supplied. A modern model with a nominal power of 40 to 50 W left on its maximum factory level permanently absorbs between 35 and 48 W to force an unnecessary flow through the bypasses. Once adjusted to the proportional curve corresponding to the project's actual operating point, its absorbed power drops to between 8 and 18 W in normal operation.

To validate the operating point on site, the heating fitter compares the displayed power with the actual temperature difference between the flow and return of the circuit. If a network designed for a difference of 15 K (for example flow at 60 °C and return at 45 °C) operates with a measured delta T of only 5 K, the water velocity is excessive and the flow carried far exceeds the thermal need of the rooms. Lowering the curve by half a metre or one metre of water column slows the flow, restores the design thermal regime and reduces the motor's electricity bill.

Circulator behaviour according to the selected control mode
Selected modePressure change at reduced flowAcoustic risk at the valvesObserved electrical consumption
Maximum fixed speed (factory setting)Sharp increase (sliding along the curve)Very high (throttling and continuous whistling)Maximum and constant (35 to 60 W)
Constant pressure (Delta p-c)Strictly constant at the setpointMedium to high at nearby heating elementsModerate, proportional to flow (15 to 35 W)
Variable pressure (Delta p-v)Linear decrease towards 50% of the setpointNone if the initial head is properly sizedOptimal at part load (6 to 18 W)

A contractor who hands over an installation without setting the circulators fails in his finishing obligations. Under art. 364 CO, the contractor is responsible for the proper and faithful execution of the work entrusted to him. A circulator that is noisy at reduced demand or stuck at maximum power leads to complaints from users and a waste of primary energy directly attributable to the defect in hydraulic commissioning.

Diagnosing malfunctions: residual whistling, insufficient flow and energy drift

On an installation that has been accepted, the appearance of hydraulic noise or a lack of heat at remote heating elements signals a critical discrepancy between the circulator's programming and the actual impedance of the distribution. Equipment left on its factory setting generates excessive differential pressure as soon as the control devices are partially closed. To durably resolve acoustic and thermal problems without changing the pipework layout, the heating installer proceeds by methodical elimination on the curves and components.

  1. Neutralising the whistling of thermostatic valvesWhen the thermostatic valves emit a continuous whistle, the local differential pressure exceeds the permissible limit. If the pump is running on a constant pressure curve (Δp-c), closing the loops transfers the hydraulic load to the last radiators left open. The remedy consists of switching the unit to variable differential pressure (Δp-v) and lowering the pump head setpoint in steps of 0.5 mWC to reduce the rotor speed.
  2. Eliminating insufficient flow in disadvantaged circuitsIf the emitters furthest from the boiler room remain cold at part load, the proportional curve restricts the available flow too severely. On older networks where the pressure losses of the distribution risers dominate those of the radiators, the setpoint value H must be raised or a constant pressure (Δp-c) at a reduced level reprogrammed, while also redoing the presetting of the balancing valves at the foot of the riser.
  3. Detecting electrical power anomaliesA measured electrical consumption that exceeds the calculated theoretical power reveals a volume flow rate outside tolerance. This shift to the right of the characteristic curve frequently results from a poorly calibrated differential valve, a leaking three-way valve or a non-return valve stuck in the open position creating a hydraulic short circuit. Directly checking the display in watts confirms that the equilibrium point is restored as soon as the parasitic bypass is neutralised.

Frequently asked questions

How can a cavitation noise be distinguished from a thermostatic valve whistle linked to the circulator?

A high-pitched whistle localised at the heating element comes from excessive flow velocity caused by too high a differential pressure when the thermostatic plug closes. The remedy is to switch the circulator to a proportional curve (Δp-v). Conversely, cavitation produces a dull crackling similar to gravel in the pump body, caused by insufficient suction pressure (lack of static cold-water pressure at the suction).

Which mode should be chosen between constant pressure and variable pressure for an underfloor heating system?

Underfloor heating requires a constant differential pressure mode (Δp-c). Unlike radiators fitted with thermostatic valves that close progressively, floor manifolds operate with on/off actuators controlled by a room thermostat. The circuit's pressure losses are almost exclusively concentrated in the pipe loops embedded in the screed, and not in the upstream risers. Maintaining a constant pump head guarantees the assigned flow in each loop that remains in demand.

Why does the circulator show an electrical consumption twice the expected value?

This overconsumption generally occurs when the unit is configured to a maximum fixed speed or to an uncalibrated factory mode. If the actual pressure losses of the network are lower than anticipated or if a relief valve opens untimely, the flow runs away and the operating point slides to the right. By adjusting the variable differential pressure curve to the nominal design point, the absorbed power drops drastically.

Can a mechanical differential valve be kept with an electronic variable-speed circulator?

As a general rule, the mechanical differential valve becomes superfluous with a circulator controlled on variable pressure (Δp-v), because the pump automatically reduces its speed when the valves close. If it is kept without changing its setting, it opens prematurely, distorts the circulator's pressure measurement and creates a thermal short circuit. It should either be shut off or have its setting tightened beyond the maximum pump head programmed on the pump.

In the same section