Key takeaways
- Rigorous calculation of the nominal flow rate prevents the overheating of riser bases at the expense of the upper floors.
- The SIA 384/1 standard requires a distribution sized to guarantee the nominal flow rates at each emitter.
- Each preset balancing valve compensates for pressure losses that vary with the distance from the boiler room.
- The reading recorded on the as-built diagram guarantees traceability and simplifies future technical troubleshooting.
From the heat balance to the calculated flow rate per distribution circuit
Hot water systematically takes the path offering the lowest hydraulic resistance. Without a deliberate, calculated restriction, the heat-transfer fluid short-circuits the network from the first branch connections onwards: radiators on the ground floor or close to the boiler room receive an excessive flow rate, causing uncontrollable overheating and flow noise at the valve seats. Conversely, apartments at the end of the line or under the roof suffer from chronic under-flow and never reach the room temperature required for occupant comfort.
- Calculated flow rate per circuit
- Hourly volume of water needed by a branch or an emitter to transfer the required heat output while complying with the contractual temperature regime, expressed in litres per hour.
To size the distribution correctly, the installer relies on the SIA 384/1 standard, which governs the design of heating installations in buildings. The conversion of the heat load into a volume flow rate uses the temperature difference planned in the project between flow and return. For the same heat load of one thousand watts, the required flow rate triples when moving from a conventional radiator circuit calculated with a temperature drop of fifteen kelvins to an underfloor heating manifold sized for a difference of five kelvins. This ratio determines the pipe cross-section and the size of the balancing devices.
| Emitter or section | Heat load [W] | Temperature difference Delta T [K] | Calculated flow rate per circuit [l/h] |
|---|---|---|---|
| Master bedroom radiator | 1 200 | 15 (65/50 regime) | 69 |
| Apartment floor manifold | 4 800 | 5 (35/30 regime) | 825 |
| North riser, 1st to 4th floor | 9 500 | 15 (60/45 regime) | 545 |
| Main basement distribution | 32 000 | 10 (45/35 regime) | 2 752 |
Valve presetting and recording of measurements on the diagrams
The physical adjustment is made using dedicated devices installed at the base of each riser and on each manifold branch. A preset balancing valve incorporates a calibrated orifice or a conical-profile plug operated by a micrometric handwheel. The figures engraved on the valve dial correspond to a precise flow coefficient value, determined by the technical office from the pressure loss to be created to compensate for the proximity of the main circulator.
- Initial positioning of the balancing devicesSet each valve handwheel to the graduation prescribed by the calculation sheet before final filling with water. Lock the internal locking ring using an angled hex key to prevent any unintentional manual change during later maintenance.
- Connecting the differential measuring computerInsert the needles of the electronic measuring device into the pressure test points located upstream and downstream of the valve seat. The device instantly calculates the actual flow rate through the pipe from the observed differential pressure.
- Progressive compensation of the distribution loopsCarry out the adjustment starting from the risers close to the distributor and moving towards the distant risers. Adjust the handwheel until the actual flow rate matches the theoretical nominal flow rate, allowing a maximum deviation of plus or minus ten per cent.
Once the installation has been calibrated, the reading recorded on the as-built diagram formalises the conformity of the work. The installer writes with an indelible marker, or on a riveted label next to the device, the valve identification number, the final setting value, the differential pressure measured in kilopascals and the flow rate recorded. This duplicate must appear on the laminated schematic diagram displayed in the boiler room. This document is the contractual reference for acceptance of the work and allows maintenance technicians to restore the set flow rates immediately after a riser has been drained.
Step-by-step balancing method: from the riser to the distributor
Water systematically chooses the path offering the lowest mechanical resistance. In an unbalanced heating installation, the radiators or floor manifolds closest to the heating plant receive a massive excess flow, while the terminals at the end of the riser suffer from a chronic heat shortage. To counter this disorder and meet the requirements of the SIA 384/1 standard, the installer must convert the theoretical flow rate values into targeted pressure losses by means of balancing devices.
Commissioning a two-pipe network or a collective distribution system always begins with the complete opening of all terminal devices (thermostatic valves removed or opened to the maximum, zone valves engaged manually). The main circulation pump is locked at its calculated fixed set point, with no pressure modulation during the measuring operations.
- Reference check on the most disadvantaged riserConnect the electronic differential pressure gauge to the pressure test points of the balancing valve located at the point furthest, geometrically or hydraulically, from the circulator. Read the residual differential pressure and the instantaneous flow rate.
- Applying the theoretical presettingSet the graduated handwheel of each preset balancing valve to the opening value taken from the hydraulic calculation table. Each valve has a numbered scale (whole turns and tenths) corresponding to a precise kvs value.
- Adjustment by the proportional methodMeasure the ratio between the actual flow rate and the calculated flow rate per circuit on the reference valve. Throttle the upstream risers one after another: each partial closure increases the pressure available for the distant sections without changing the relative proportions already established.
- Mechanical locking of the strokeOnce the nominal flow rate has been set within the permitted tolerance, tighten the internal stop screw (micrometric locking screw) using a hex key to prevent any unintentional closing during maintenance operations.
Measurement protocols, traceability and recording on drawings
Hydraulic balancing does not end with setting the handwheels: it requires rigorous documentary traceability to guarantee the long-term operation of the system and to prevent disputes at acceptance of the work under the SIA 118 standard. The installer records each value observed on a test sheet attached to the as-built file.
| Valve ref. | Zone served | Calculated flow rate (l/h) | Presetting (index) | Measured Delta p (kPa) | Measured flow rate (l/h) | Deviation (%) |
|---|---|---|---|---|---|---|
| V-COL-01 | Ground floor West | 1'450 | 2.8 | 14.2 | 1'480 | + 2.0 % |
| V-COL-02 | 1st floor West | 1'320 | 3.1 | 12.8 | 1'300 | - 1.5 % |
| V-COL-03 | 2nd floor West | 1'150 | 3.6 | 11.5 | 1'170 | + 1.7 % |
| V-COL-04 | Attic (disadvantaged) | 980 | 4.2 | 10.1 | 960 | - 2.0 % |
| V-DIST-01 | Floor manifold, 1st floor | 820 | 2.4 | 15.0 | 840 | + 2.4 % |
On the construction site, the durability of the setting requires an indelible identification. The mechanical index value adopted after balancing must be transferred with an industrial indelible marker or by a label engraved directly on the collar or the insulation housing of the valve. If the valve is removed for cleaning or pipe flushing, the operator immediately finds the exact position without recalculation.
The reading recorded on the principle diagram in the boiler room is the last safeguard against operational drift. Next to each symbol of a balancing device, the installer notes the final measured flow rate and the residual pressure loss value. This laminated document stays hanging in the boiler room, available to the foreman and the maintenance service.
Diagnosis of flow rate deviations and corrective protocols
When the first level overheats while the top floor struggles to reach its set temperature, the network is suffering a major hydraulic short circuit. If a preset balancing valve does not show the calculated flow rate per circuit expected under the SIA 384/1 standard, the heating installer must never compensate for this imbalance by increasing the speed of the circulator. This shortcut increases electricity consumption, lowers the efficiency of heat generation and causes flow noise and whistling at the thermostatic valves, without delivering the required heat to the distant emitters.
- Air bleeding and filter checkCheck that there is no residual air at the top of the riser and inspect the dirt separator or the strainer of the substation. A partially clogged strainer causes a parasitic pressure loss that immediately distorts the differential pressure available at the balancing valves.
- Regulating the favoured sectionsMethodically throttle the lower manifolds and risers by screwing the millimetric vernier of the valve in fractions of a turn. Immediately check on the computerised differential measuring device the resulting increase in mass flow rate in the under-supplied terminal branches.
- Checking valve authorityMake sure that the balancing valve keeps sufficient authority against the load variations induced by the thermostatic heads. If the static device cannot stabilise the branch, a differential pressure regulator must be integrated.
After hydraulic stabilisation of the whole network, each measurement result must be rigorously traced. The reading recorded on the technical distribution diagram states the actual volume flow rate in litres per hour, the residual pressure loss in kilopascals and the mechanical setting index of each valve. This completed as-built drawing is included in the as-built documentation file, guaranteeing the client an installation that is compliant, reproducible during future maintenance and free of thermal comfort disputes.
Frequently asked questions
How should you react if the flow rate measured on a riser remains 30 % below the design value?
A deviation of this size reveals either an unforeseen pressure loss in the network, a clogged filter, or insufficient driving differential pressure in the boiler room. The installer first checks the cleanliness of the upstream strainer and the complete venting of the riser. If the circulator does deliver its nominal pressure, the nearby priority risers should be throttled progressively to shift the fluid towards the deficient circuit, and the new setting should then be recorded.
Why is it not enough to simply increase the speed of the circulation pump?
Increasing the pump output does not solve the hydraulic disparity between risers: it worsens the excess flow in the short circuits and saturates the nearby emitters. This residual overpressure causes flow noise and whistling at the thermostatic valves as soon as they close. In addition, the excess electricity consumption of the circulator penalises the overall energy balance of the installation, without ensuring the required thermal comfort on the upper floors.
What is the permissible tolerance between the measured flow rate and the calculated flow rate?
In construction site practice according to the rules of the trade, a deviation of plus or minus 10 % from the calculated flow rate per circuit is generally accepted for radiators and risers. This margin absorbs approximations in pipe roughness and slight manufacturing variations of the balancing devices. Beyond 15 %, the thermal imbalance becomes noticeable to the occupants and requires a systematic readjustment of the presetting positions.
What exactly should be entered when recording the reading on the distribution diagram?
The installer notes on the technical diagram the valve identification reference, the design flow rate value and the actual flow rate measured in litres per hour. They add the differential pressure read in kilopascals and the precise graduation of the locking vernier. These figures, initialled by the technician, make it possible to find the initial setting immediately in the event of unwanted tampering during future maintenance work.
Texts and standards cited
- SIA 384/1Heating installations in buildings - Requirements and sizing
