Skip to content
Website
🧱 CFC 241Hydraulic distribution and balancingChapter 10 of 10 in the section

Metering per dwelling: meter position, accuracy and disputes

This chapter details the hydraulic and administrative installation rules for thermal energy meters in multi-occupancy housing. You will learn how to position the measuring element correctly, observe the straight lengths required for volumetric measurement, connect the temperature sensors without loop errors, and secure traceability through an initial joint reading.

Key takeaways

  • Fit the meter on the specified pipe, strictly observing the volumetric flow arrow.
  • Maintain the upstream and downstream straight lengths required by the manufacturer to stabilise the water flow.
  • Physically check the pipe routing so as not to connect the dwelling to the neighbouring riser.
  • Sign a joint zero-reading report including the serial and batch numbers.

Positioning of the measuring body and geometry of the hydraulic connections

In a rental building or a condominium ownership property, the thermal energy meter measures the volume of heating water distributed and the temperature difference between flow and return of an apartment. A positioning error distorts the entire individual heating cost statement. Before any mechanical fixing, the fitter must check the configuration of the electronic integrator. Most compact models are factory-set to be installed on the return of the secondary circuit, where the fluid temperature is lower, which protects the on-board electronics and the lithium battery. Installing a device set for the return on the flow pipe distorts the calculation of the water density and causes a systematic drift in the measured power.

The direction of fluid flow remains the first point of vigilance when tightening the threaded fittings. An arrow stamped on the brass body indicates the flow direction. A single-jet, multi-jet or ultrasonic meter fitted the wrong way round records negative volumes or goes into a flow fault, which blocks metering. Upstream and downstream of the measuring spool, hydraulic disturbances created by bends, branch tees or reduced-bore stop valves disturb the fluid velocity profile. To guarantee class 2 metrological accuracy, an undisturbed straight section must be maintained: as a general rule, a straight length equal to three times the nominal diameter (3 DN) upstream and twice the nominal diameter (2 DN) downstream is required for static ultrasonic technologies, while some mechanical models require up to 5 DN upstream if no jet stabiliser is built in.

Distances and installation requirements by type of flow sensor
Measuring technologyUpstream straight lengthDownstream straight lengthUsual hydraulic positionCritical installation point
Ultrasonic (static)3 DN (per data sheet)2 DN or 0 DN depending on manufacturerApartment returnAir bubbles trapped at high point
Single-jet axial turbine5 DN without obstruction2 DNApartment returnFouling by ferrous sludge
Multi-jet turbine3 DN to 5 DN2 DNApartment returnSensitivity to upstream eddies

Assignment of technical units, traceability and joint zero reading

The most serious mistake on a new apartment building construction site is crossed pipework in the landing shafts. When two heating flow pipes supply two adjacent apartments from the same distribution riser, a marking-out oversight leads to the meter of apartment 201 being fitted on the branch serving apartment 202. The more economical occupant thus pays their neighbour's energy bill. To eliminate any risk of swapping, the installation team must carry out a physical check by blowing through or by thermal circulation: circulate the fluid valve by valve and confirm the temperature rise of the floor manifold or radiators inside the dwelling concerned before sealing the meter.

  1. Marking out and visual identification of circuitsFollow each pipe from the riser valve to the internal distributor. Mark the official condominium unit or dwelling number indelibly on the flow pipe and on the return pipe.
  2. Device conformity checkCheck that the serial number engraved on the casing matches the metrological calibration certificate and that the manufacturer's seals are intact.
  3. Recording the initial readingsNote the value displayed in megawatt-hours or kilowatt-hours, the cumulative water volume in cubic metres and the integrated radio or wired physical address.
  4. Sealing and fitting of security sealsFit a sealed security collar on the valve body nuts and on the temperature sensor nut to prevent any unauthorised removal.

Once the installation has been pressurised, purged and balanced, the foreman draws up the joint commissioning report. This document legally binds the installer, the site management and the client or the appointed property management company. Art. 367 CO provides that the client must inspect the condition of the work as soon as is possible in the ordinary course of business. By recording the starting reading in writing, often slightly above zero because of heating-up tests and flushing of the installation, one avoids a cost linked to slab drying works being charged under the lease to the first incoming tenant.

Hydraulic installation rules: straight lengths, flow direction and sensor immersion

The thermal energy meter measures the heat delivered to an apartment from two physical quantities: the volume of circulating water and the flow-return temperature differential. Metrological reliability depends on the hydraulic connection. Every ultrasonic or mechanical metering body carries an arrow cast into its housing. This arrow must follow the actual flow direction of the heat-transfer fluid. The installer must scrupulously observe these visual markings to rule out any later malfunction. A reversed installation stops metering or generates an error code on the display. In addition, the body must occupy the hydraulic line corresponding to its factory calibration: on heating risers, it is installed on the apartment return in order to protect the calculation electronics from the high flow temperatures.

To stabilise the fluid velocity profile, manufacturers recommend a straight section immediately upstream of the device, with no regulating valve, tee or sharp bend. Even though some ultrasonic models hold a metrological approval without straight length, good practice is to provide five nominal diameters upstream and two nominal diameters downstream of the connection. This precaution protects the measuring signal from hydrodynamic turbulence. The meter must never be placed at the high point of a loop: air pockets disturb the ultrasonic measurement or slow the turbine. The device is installed on a horizontal section or on a vertical rising riser, under constant static pressure to prevent cavitation.

Common hydraulic installation faults and metrological impacts
Fault foundTechnical impactConsequence on the billCorrective measure
Return meter fitted on the flowError in density and specific heat capacityBilling drift of 2 to 4 %Reposition the device on the loop return
Flow arrow reversed on the pipeMeasurement stops or negative recordingUnrecorded consumption or error codeReverse the installation direction of the hydraulic body
Flow and return sensors swappedNegative temperature differential (delta T < 0)Energy calculation blocked with no kWh accumulationSwap the sensors into the correct thermowells
Direct bend with no upstream straight lengthTurbulence and asymmetric flow profileVolume measurement error of 5 to 15 %Insert a straight stabilising pipe of 5 DN

Assignment of units, individual check and joint zero reading

In a technical shaft serving several apartments, the main cause of disputes is the physical crossing of pipework. Connecting the circuit of dwelling 201 to the meter labelled for dwelling 202 results in the tenant being billed for their neighbour's consumption. This error is not detected during remote readings: the communication gateways transmit consistent volumes that conceal the swap until service-charge disputes arise at the annual statement. This technical defect leads to complex claims and retroactive re-billing that are particularly damaging for the property management.

  1. Individual thermal checkClose all distribution valves in the shaft. Open only the circuit of the dwelling being checked. Verify with a contact thermometer that the temperature rise occurs at the corresponding meter and that the instantaneous flow increments.
  2. Checking sensors and sealsCheck that the red sensor is fitted on the hot flow and the blue sensor on the return. Fit metrological seals or tamper-proof rings on the fittings and thermowells to prevent any later tampering.
  3. Traceability of identifiersNote the calculator's serial number, the foundry serial number and the physical address of the communication bus. Formally link this information to the official unit number or to the condominium ownership register.
  4. Zero-reading reportRecord the energy and volume readings at commissioning. Have the joint document countersigned by the site management or the manager before the occupants take possession of the premises.

The initial joint reading records the starting index before any handover. It avoids charging tenants for the energy consumed during technical tests or building drying. Under the Code of Obligations, the client inspects the condition of the work as soon as possible after delivery. A written record, supported by photographs of the readings and of the sealed serial numbers, provides incontestable proof of the installation's conformity and durably protects the installer. This complete execution file is an essential appendix to the acceptance report for the technical installations.

Handling assignment disputes and rectifying non-conformities

When a billing inconsistency appears in the first heating statement, the complaint systematically goes back to the installer. The typical case is the physical swapping of two meters in the landing technical shaft or the wrong allocation of a serial number when integrating into the remote-reading gateway. The tenant who is away all winter inherits the consumption of the neighbouring family. Towards the client, the installer is liable for defects in their work under the applicable provisions of the Code of Obligations, in particular art. 368 CO on the client's rights in case of defects.

  1. Joint thermal shut-off testIn the presence of the property management or the client's representative, close the isolation valves of the distributor of a single apartment. Check on the calculator that the instantaneous flow immediately drops to 0 l/h. If the meter continues to record water passing, the hydraulic connection serves another unit.
  2. Physical check of straight lengths and directionInspect the measuring spool. The arrow engraved on the brass body must point in the direction of fluid flow. Measure the clearances: a bend or a ball valve placed right against the upstream side disturbs the flow profile and causes a measurement drift outside metrological tolerance.
  3. Checking sensors and pairingCheck the position of the Pt1000 probes. A flow sensor inadvertently fitted on the return completely distorts the delta T calculation and blocks thermal energy metering. Read the engraved physical identifier and compare it with the logical address sent to the data manager.
  4. Drawing up the rectification reportRecord the actual readings on the day of the check, the corrected manufacturing numbers and the final reassignment of the technical units. This signed document allows the property management to recalculate the consumption history without arbitrarily penalising the users.

Frequently asked questions

How should you react when a thermal meter shows a negative flow at commissioning?

A negative flow or a flow error on the calculator indicates a reversed installation direction. The water passes through the measuring body in the opposite direction to the indicator arrow. Drain the section, remove the threaded fittings, replace the flat gaskets and reposition the device in the correct flow direction before restarting the recording of the energy readings.

What should you do if the technical shaft does not offer the required upstream straight length for the meter?

Consult the manufacturer's metrological approval instructions. Several recent ultrasonic models accept an installation class with no upstream or downstream straight length. If the installed model requires three nominal diameters upstream, you must move the isolation valve or insert a calibrated straight spool to stabilise the hydraulic flow and guarantee the required measurement accuracy.

When should the joint zero reading of a group of apartments be signed?

The initial joint reading takes place precisely at the changeover between the screed drying phase and the handover of the work to the client. Before that date, the heat consumed for the construction site falls under construction overheads. The zero reading fixes the starting index chargeable to tenants in a formally countersigned report.

Which method identifies the connected apartment without entering the tenant's home?

Open the landing technical shaft door and observe the calculator. Force the setpoint from the substation or operate the control valve of the unit concerned. Read the temperature rise on the flow thermometer and observe the change in instantaneous flow displayed in m³/h on the digital dial to confirm the exact physical assignment.

Texts and standards cited

  • CO art. 368client's rights in case of defects in the work: refusal, price reduction, rectification, damages; any clause agreed in advance that restricts or excludes the right to have defects remedied is void if the defect concerns a building (para. 2bis, since 1 January 2026).

In the same section