Key takeaways
- Section three reveals the active substances, the organic solvents and the actual volatile compounds.
- Section eight dictates the appropriate respiratory filters and the material of the protective gloves.
- Section four specifies the life-saving emergency response before calling specialist medical help.
- Section thirteen guides the management of residues according to the cantonal special-waste channels.
Identify the real risks from the composition and choose suitable protection
In a site folder or on a digital tablet, the safety data sheet has sixteen regulatory sections. For the site foreman and the painters, the preliminary analysis does not consist of reading every paragraph of general toxicology, but of extracting the technical data that govern the immediate work. The sheet must be available for consultation by the applicators at the actual place of work, in accordance with the federal occupational safety requirements and the Chemicals Ordinance. Keeping this document in the technical office protects no one in the application area.
| SDS section | Technical subject | Immediate decision on the construction site |
|---|---|---|
| Section 3 | Composition and solvents | Check the content of solvents, isocyanates or reactive resins to adapt the forced ventilation. |
| Section 4 | First aid | Set the course of action in case of eye splash, skin contact or inhalation of toxic vapours. |
| Section 8 | Controls and protection | Select the exact class of respiratory cartridges and the resistant polymer for the gloves. |
| Section 13 | Disposal of residues | Determine whether pasty leftovers, can bottoms and cleaning water count as special waste. |
Identification starts with the hazard pictograms in section two and the signal words. The red-bordered diamond with an exclamation mark signals the frequent skin irritation or sensitisation caused by epoxy or solvent-based acrylic paints. The flame-over-circle-type heat symbol ... more precisely, the thermal-bomb symbol identifies highly flammable liquids, requiring a ban on all hot work and the disconnection of sources of sparks. The hazard statement informs about the mechanism: the statement indicating skin sensitisation requires a strict protocol with no contact whatsoever with the skin, while the statement describing drowsiness requires reinforced air extraction.
Section three details the hazardous components with their mass concentration. A painter immediately checks the proportion of aromatic solvents or esters. This content directly guides the reading of section eight, devoted to exposure control and personal protective equipment. It is not enough to order the wearing of a mask: section eight specifies the type of filter required. For primer coats or polyurethane varnishes applied by spray gun, a half-mask fitted with a filter combining organic vapours and solid particles is required. For epoxy resins, the section defines the material of the impermeable gloves, often ruling out thin latex in favour of butyl rubber or nitrile of certified thickness.
Apply first aid and dispose of residues through the legal channels
The ordinance on safety and health protection of workers in construction work requires a rigorous organisation of first aid. Section four of the safety data sheet is the operating manual in the event of an accident at the workstation. The team must memorise its key points before opening the drums of primer or hardener.
- Eye splash of hardener or resinImmediately rinse the open eye under a gentle stream of lukewarm water or with a sterile eyewash bottle for at least fifteen minutes without rubbing, then consult a doctor with the sheet.
- Skin contact with a corrosive or solvent-based productImmediately remove soiled clothing, wash the skin with plenty of water and mild soap, and strictly never use thinner or cleaning solvent.
- Acute inhalation of solvent vapours in a confined spaceMove the victim to a ventilated area in the open air, keep the worker at rest and warm, and have the emergency medical service alerted if dizziness or malaise persists.
- Accidental ingestion by siphoning or mix-upNever try to make the person vomit, to avoid the solvent being drawn into the lungs; rinse the mouth with clear water and contact the Swiss poison centre.
End-of-day management and clearing of the workstation fall under section thirteen. Under the ordinance on the avoidance and disposal of waste and the ordinance on the movement of waste, residues of liquid paint, gun-cleaning solvents and undrained packaging are special waste. The sheet gives the applicable waste code and specifies whether the product can be neutralised or must be taken to an approved collection centre.
Quick decoding of section 2: GHS pictograms and hazard statements
On the tin delivered by the paint supplier, the label gives the alarm signal, but it is section 2 of the safety data sheet that frames the real exposure risk. Drawn up according to the criteria of the Globally Harmonised System incorporated into the Chemicals Ordinance, this section summarises the classification of the preparation. For the team leader, it is not for memorising standard phrases, but for determining immediately whether the product requires forced ventilation, specific gloves or isolation of the workstation from the other trades.
Hazard statements (H phrases) qualify the exact nature of the physical, health or environmental hazard, while precautionary statements (P phrases) dictate handling reflexes. A qualified painter can spot critical combinations within seconds, especially when a polyurethane resin or a two-component varnish combines high volatility with agents that sensitise the skin and respiratory tract.
| Symbol and hazard statement | Examples of paint products | Immediate consequence on the construction site |
|---|---|---|
| GHS02 (Flame) / H226: Flammable liquid and vapour | Solvent-based primers, glycerophthalic lacquers, synthetic cellulosic thinners | Ban on hot work, switch off bare-element site heaters, continuous ventilation of the room. |
| GHS07 (Exclamation mark) / H317: May cause an allergic skin reaction | Epoxy bonding resins, polyamine hardeners, acrylic paints with isothiazolinone additives | Wear thick nitrile gloves with cuffs; never clean fresh film off the skin with thinner. |
| GHS08 (Health hazard) / H373: May cause damage to organs through prolonged or repeated exposure | Two-component floor paints, solvent-based woodwork varnishes, sprayer cleaners | Combined-cartridge respiratory protection mandatory, rotation of applicators, air-change measurement. |
| GHS09 (Environment) / H411: Toxic to aquatic life with long-lasting effects | Facade fungicides, biocidal exterior stains, silicate paints with algicide additives | No discharge to the sewer or onto bare ground; clean sleeves and brushes only over a closed settling tank. |
The reading of section 2 must always be set against the application technique chosen. A solvent-based stain applied by roller in a stairwell generates a moderate vapour concentration if natural ventilation is constant. The same product sprayed at high pressure with an airless unit without mist creates a cloud of micro-droplets that saturates the atmosphere within minutes and completely changes the level of respiratory protection required.
Keeping and providing access to SDSs on the construction site: ChemO compliance and practical reflexes
The Chemicals Ordinance requires the manufacturer and the distributor to supply an up-to-date safety data sheet, but responsibility for making it available at the workstation lies entirely with the employer. On a renovation or new-build construction site, an SDS filed at the company's head office thirty kilometres away is regarded as non-existent during an inspection by the cantonal labour inspectorate or SUVA. The document must be available without delay to the applicator, the team leader or the medical emergency services.
- Centralise the paper safety folder in the preparation areaPlace a rigid waterproof folder directly in the paint storage room or the site cabin. This folder contains the printed French-language paper version of the SDSs for each product present on the site, filed by trade name with a clear index on the first page.
- Deploy direct digital access without an authentication barrierIf the company opts for a site tablet or professional smartphone, the documents must be downloaded locally to cope with dead zones (basements, windowless technical rooms). Access must not require any complex password in an emergency.
- Display simplified notices at the mixing stationsFor frequently handled products such as epoxy paints or cleaning solvents, stick above the mixing table a workstation sheet summarising the pictograms, the prescribed PPE and the national emergency number.
Finally, SDS management is not limited to passive receipt. With each formula revision notified by the paint supplier, the new version must replace the old one in the site folders. The accident prevention ordinance requires workers and apprentices to be instructed on the risks inherent in the substances used. Taking ten minutes during the safety quarter-hour to read the sections of a new paint system together avoids dangerous improvisation during cleaning or intensive application phases.
Emergency procedure: managing the chemical accident and the construction site inspection
On a painting construction site, the situation often tips over on a poorly mastered reflex action: a pressurised epoxy hardener splashed into the eyes, acute dizziness in an applicator confined with a solvent-based primer, or a thinner can splitting on a raw floor. In a crisis, the safety data sheet ceases to be a mere folder item: it becomes the immediate survival instruction. Any improvisation aggravates the bodily harm or the pollution.
- Extract and secure the victimCut off the source of exposure immediately. Carry the worker into the open air while avoiding exposing yourself to the heavy vapours. If a solvent-based product is flammable, forbid any spark, switch off the compressors and ventilate the room without delay.
- Apply the first-aid section without improvisingConsult the dedicated section of the sheet. In case of eye or skin splash, rinse with plenty of lukewarm water for at least fifteen continuous minutes. Never make the victim vomit after ingestion of solvents and do not give milk.
- Alert the emergency services with the hazard statementsCall Tox Info Suisse on 145 for poisoning or 144 for a life-threatening emergency. Give the exact product name, the manufacturer, the chemical registration number and the list of hazardous components taken from the composition section.
- Contain the spill according to the disposal channelDam the leak with absorbent binders for hydrocarbons or dry sand. Never discharge a spill into the municipal sewers or a stormwater drain. Collect the polluted sludge in a sealed drum marked for the special-waste channel.
Once the people have been stabilised and the premises secured, the team leader records the event in the site diary. He passes the incident report to the site management and keeps a copy of the relevant sheet for the insurer and occupational medicine.
Frequently asked questions
Where exactly should safety data sheets be kept on a construction site?
The documents must be grouped in a waterproof folder placed in the site canteen or the paint preparation area. The employer may use a digital format on a tablet or professional phone, on the absolute condition that every painter and team leader knows the access code, that the network works in basements and that a charged battery is guaranteed at all times.
Can a painter decant cleaning solvent into an unmarked bottle?
This practice is strictly prohibited on all Swiss construction sites. Any reused container, even temporary, must immediately carry the original labelling: exact trade name of the product, GHS hazard pictograms as indelible adhesive labels and risk statements. Using food packaging such as water bottles exposes the construction site to serious accidental ingestion and to a work stoppage.
What should be done with rags and rollers soaked in oil for exterior woodwork?
Natural or synthetic oils based on drying oils present a proven risk of self-ignition by oxidation in open air. Soaked rags, pads and sleeves must be immersed in water immediately after use, then stored in a closed airtight metal container. Their disposal must be carried out via the cantonal special-waste channel, in accordance with the requirements of the disposal section.
Why does the composition section of the sheet often give percentage ranges?
Paint manufacturers protect their industrial formulas by giving concentration ranges for the active substances and solvents. For the painter, only the upper limit counts in assessing the maximum risk: a solvent listed at between ten and twenty-five per cent requires respiratory protection and artificial ventilation to be sized as if the product contained the full quarter.
Texts and standards cited
- OPChimRequirements on placing on the market, classification, labelling and communication of safety data sheets for chemical products
- OTConstRequirements on air quality, respiratory protection, the organisation of first aid and safety at the workstation
