Skip to content
Website
🧱 CFC 272Section 2 of 610 chapters

Interior paint systems: selection and application: the execution reference

This section is aimed at team leaders, foremen and site managers who must specify and carry out interior painting work in compliance with SIA 257. It details the essential technical sequence between substrate preparation, the application of a suitable primer, the intermediate coat and the choice of finishing film. It guides you in eliminating visible touch-ups, controlling saturated colours and securing damp rooms without compromising profitability.

  • 10chapters
  • 22 000words
  • 6sections in the training course
  • 60chapters in total

Key values to remember 4

norme SIA 257

5 °C

Minimum ambient air and substrate temperature for the application of dispersion paints

norme SIA 257

80 %

Maximum relative air humidity permitted during interior painting

norme SIA 257

3 %

Maximum moisture content by mass of a plaster to allow the application of a system

art. 33 OTConst

21 %

Maximum oxygen content by volume required to preserve indoor air quality

Scope of work of the interior painter and construction site interfaces

The role of the building painter (CFC 272) is to build up a durable, protective and aesthetic film-forming system on a stabilised substrate. The painter's task is not to correct defects in plumbness, overall flatness or structural hollows attributable to the structural work or to lightweight partitions. According to the recognised rules of the art and SIA 257, the painting contractor takes over a substrate prepared by other trades, in particular the plasterer (CFC 271). If a surface shows unevenness or a roughness outside the tolerance for the agreed level of requirement, the contractor applies the duty to notify under art. 365 CO para. 3 before any painting is carried out, without taking the plasterer's place for heavy reprofiling of the walls.

Delimitation of technical responsibilities around the interior painting package
Trade / CFCSole responsibility of the third-party tradePainter's take-over point (CFC 272)
Plastering and staff (CFC 271)Overall flatness, joint tapes, complete plasters and agreed surface levelsCohesion check, light sanding to remove loose grains, consolidation of substrates by impregnation
Screeds and floors (CFC 281)CM moisture measurement for screed acceptance, self-levelling floor smoothing compoundsIndicative moisture test to refuse or approve installation on skirting boards or thresholds
Parquet floors (CFC 283)Sanding of the wood, impregnating oil treatment and varnishing of floorsAirtight protection of the boards when painting the walls
Facades and ETICS (CFC 221)Installation of external thermal insulation, reinforcement and base facade rendersRefresher paint on existing renders without reworking the insulation

Likewise, the structural anti-corrosion protection of load-bearing beams and columns is the responsibility of the metal construction contractor (CFC 215). The interior painter treats radiators, exposed secondary pipework and metal door frames for interior distribution. On each element, the preliminary analysis of the surface condition determines the mechanical and chemical adhesion of the whole system.

Execution method: logical progression of the ten chapters

The success of an interior painting job depends on strict compliance with the application chain. To guarantee a result that is beyond dispute at the acceptance of the work, the technical chapters must be learned in a sequential, site-based order, from the compatibility of chemical formulas through to the final handover of the walls.

  1. 1. Master the complete system and the tools (O2-01 to O2-03)The applicator selects a consistent range from a single manufacturer to prevent conflicting chemical reactions. They adapt the roller sleeve, spray nozzle or brush bristle to control the film tension and avoid patchiness requiring touch-ups.
  2. 2. Adapt the formulas to physical constraints (O2-04 to O2-07)Each substrate has its own rules: waterproofing and scrub resistance in wet rooms, tinted intermediate coats to support saturated bright colours, tannin blocking on woodwork and heat resistance on heating systems.
  3. 3. Secure critical surfaces and the occupied environment (O2-08 to O2-10)Managing raking light on ceilings requires a deep matt finish without tension. The construction site requires rigorous prior masking and the technical refusal of partial touch-ups in favour of treating complete wall sections.

By following this technical path, the execution teams limit recurring damage: blistering on a blocked substrate, softening of an old alkaline substrate or visual defects visible under the overhead light of glazed bays.

📘 Chapters in this section 10

Interior paint systems: selection and application

Thinking in systems: primer, intermediate coat, finish coat and the same manufacturer

Secure adhesion by locking in the chemical compatibility between primer and finish within a single certified range.

Interior paint systems: selection and application

Hiding power, flashing and lap marks: working wet on wet and finishing the wall

Eliminate roller marks and patchiness by matching your working pace to the open time.

Interior paint systems: selection and application

The tool determines the finish: roller, airless spray gun, brush and the expected appearance

Select the optimal application equipment to balance speed of application and final texture without unnecessary overconsumption.

Interior paint systems: selection and application

Wet rooms: washable paint, cleaning resistance and limits against water

Prevent blistering and mould with scrubbable films formulated for frequent exposure to water.

Interior paint systems: selection and application

Deep colours: number of coats, tinted undercoat and colour durability

Achieve perfect colour depth from the second coat thanks to an intermediate coat tinted to a similar shade.

Interior paint systems: selection and application

Interior woodwork: sanding, bleeding knots and brush-mark-free lacquer

Block tannin and resin bleed-through to achieve an interior lacquer as smooth as a mirror.

Interior paint systems: selection and application

Painting a radiator: cold substrate, heat-resistant product and yellowing

Stop thermal yellowing and peeling at once by applying heat-resistant resins on cooled metal.

Interior paint systems: selection and application

The ceiling: direction of application, raking light from a glazed opening and a deep matt appearance

Banish application shadows under raking light with deep matt paints formulated to need no touch-ups.

Interior paint systems: selection and application

Mask before opening the tin: floors, joinery, furniture and condition report

Protect adjacent work and save decisive cleaning time thanks to prior airtight sheeting.

Interior paint systems: selection and application

The impossible touch-up: patching an old wall, aged shade and the whole wall

Defend technically the painting of a complete wall section against complaints about a visible localised touch-up.