Skip to content
Website
🧱 CFC 272Interior paint systems: selection and applicationChapter 6 of 10 in the section

Interior woodwork: sanding, bleeding knots and brush-mark-free lacquer

This chapter details the method for lacquering interior woodwork durably, without yellowing or application marks. You will be able to identify resin exudation, select and apply an effective tannin blocker, carry out intermediate sanding without scratching the film and master the application of a taut lacquer with no visible lap marks, in accordance with the professional requirements of standard SIA 257.

Key takeaways

  • The resins in knots pass through standard water-based lacquers within a few months unless a specific blocker is used.
  • An insulating varnish or cationic primer is applied after mechanically removing the resin pockets.
  • Sanding with fine grit between each coat ensures mechanical adhesion and removes embedded dust.
  • Even smoothing is carried out wet-on-wet, in the direction of the wood grain, without ever going back over the work.

Block resin and tannin bleed-through before any painting

On interior joinery in fir, spruce or maritime pine, the knots contain a high concentration of essential oils and terpene resins. Under a light-coloured lacquer, particularly white, the absence of a chemical barrier produces circular brown or yellowish halos that become visible after a few months. Modern water-dilutable lacquers offer no natural resistance to this physical phenomenon: the water contained in the binder dissolves the resinous matter, which migrates by capillary action through the film as it dries, then continues to seep out under the effect of ambient heat. Standard SIA 257 requires these peculiarities of the substrate to be treated to ensure the lasting appearance of the work.

  1. Thermal and mechanical removal of resin pocketsDried resin beads must be cut out with a joiner's chisel or scraped off with a steel blade. Moderately heat the surface of the knots with a temperature-controlled heat gun to draw out the trapped resin, then wipe with a clean cloth soaked in acetone or cellulose thinner.
  2. Local application of the knot blockerApply two crossed coats of a knotting varnish based on natural shellac, or of a specific solvent-based insulating product, directly onto the bare wood. This product dries quickly by solvent evaporation, encapsulating the volatile substances inside the wood channels without wetting the cellulose fibre.
  3. General insulating primerApply a blocking insulating undercoat over the entire woodwork. On tannin-rich wood such as oak or chestnut, this blocking primer prevents the finish paint from blueing or browning overall.

Ensuring a taut lacquer through methodical sanding and application without lap marks

A successful interior lacquering depends on the regularity of the levelling coats and the complete absence of roughness beneath the final coat. Even on carefully sanded wood, applying a first coat of water-based product causes the surface wood fibres to rise. If this fuzz is not cut mechanically once the coat has fully hardened, the final lacquer has a grainy texture and loses its silky feel. Moreover, managing the open time determines the smooth appearance of the lacquer, as premature touch-ups create dull patches and indelible thick spots.

Surface treatment protocol according to the finishing criteria of standard SIA 257
OperationRecommended abrasive or toolTechnical objective
Initial sanding of the raw substrateCorundum paper, grit P120 to P150Levelling the fibres and opening the wood pores
Filling and local skim-coatingOil-based filler or lacquer putty with flexible steel knifeFilling splits, cracks and joint shrinkage gaps
Sanding after primingStearated abrasive on soft sponge, grit P240Cutting off raised fibres without sanding through the base coat
Sanding of the intermediate coatStearated abrasive sheet, grit P320 or P400Creating a uniform micro-scratch key
Application of the finish lacquerHigh-density foam or 5 mm microfibre lacquering roller, soft-bristle flat brushEven deposition and continuous tensioning of the protective film
  1. Dry sanding and meticulous dust removalWork by hand with fine grit in the direction of the fibres, without pressing on the edges so as not to expose bare wood. Vacuum the substrate with a soft brush, then wipe with a slightly tacky resinous tack cloth to capture airborne microparticles.
  2. Methodical application without lap marksWork in successive zones of about fifty centimetres. Apply the lacquer evenly with the roller, cross-roll once to distribute the material load, then smooth with the flat brush in the direction of the wood grain without applying pressure.
  3. Strict respect of the wet filmNever go back over a section with the brush once it has begun to set or evaporate, otherwise you will tear the film while it is tensioning and permanently mark the product with ridges.

Chemistry of exudation and knot insulation protocol according to standard SIA 257

On interior joinery in softwoods such as spruce or Scots pine, resin pockets and knots are zones with a very high concentration of rosin and terpene acids. Under the combined effect of ambient heating and variations in relative humidity, these compounds inevitably migrate to the surface. In a white or pastel finishing system without a specific barrier, this migration causes localised yellowing by capillary action within an average of three to six months, followed by spot softening of the finish film that can lead to blistering.

Knot and tannin blocker
Primer or insulating base coat formulated with cationic resins or alcohol-based shellac, designed to form a sealed, non-water-soluble, solvent-resistant film that chemically blocks the migration of soluble wood substances into the finish film.
Behaviour of primers against the risk of resin and tannin bleed-through
Type of bonding primerAnti-tannin barrier (oak, chestnut)Anti-resin barrier (spruce, pine knots)Drying time before lacquering
Standard water-based acrylicNone (immediate water wicking effect)None (terpene migration within 6 months)4 to 6 hours
Solvent-based alkyd or glyceropthalicLow to medium (delayed yellowing)Medium (limited durability over time)16 to 24 hours
Water-based cationic primerVery high (chemical blocking of acids)Good on stable, non-weeping knots6 to 8 hours
Insulating primer based on shellac in alcoholMaximum (total sealing of the substrate)Excellent (sealed crystallisation of exudates)45 minutes to 1 hour

Standard SIA 257 governs the technical requirements for painting work on wood and wood-based materials in French-speaking Switzerland. The condition of the substrate must be rigorously assessed before any intervention. Pockets of liquid or soft resin must under no circumstances simply be masked: the internal heat of the building would continue to exert gas pressure that would lift even the most resistant lacquer.

  1. Hollowing out and thermal scrapingOpen the visible resin pockets with a gouge or a wood chisel. If the resin is sticky, moderately liquefy it with a heat gun, then soak it up with a clean cloth soaked in denatured alcohol or cellulose thinner.
  2. Structural fillingFill the cleaned cavities with a two-component polyester filler or a non-shrink epoxy filler. Do not use water-based fillers for this structural levelling stage.
  3. Application of the blocking varnishApply two local, crossed coats of shellac-based insulating primer on each knot and each filled area, overlapping by two centimetres onto the surrounding sound wood.
  4. General base coatApply an absorption-regulating base coat over all the joinery to even out the porosity of the substrate before the lacquer coats.

Sanding technique and control of lap marks in interior lacquer

Achieving a lacquer without lap marks requires a rigorous balance between the mechanical preparation of the substrate, the viscosity of the product and the rhythm of application. Sanding between each coat ensures two inseparable functions: mechanical adhesion through the creation of micro-scratches and levelling of the wood fibres raised by the moisture of the product during the first coat.

  • First sanding on raw wood or dry primer: abrasive paper on corundum foam, grit P180, always working in the direction of the wood grain.
  • Intermediate sanding between the intermediate coat and the finish: dry grit P240 or P320, without pressing on the edges so as not to sand through the base film.
  • Complete dust removal: brushing with soft bristles, then a lint-free microfibre cloth, completed by a tacky antistatic wiping pad just before painting.

The appearance of lap marks or ridges almost always results from too short an open time. In heated interiors, the evaporation of the co-solvents of a water-soluble lacquer is accelerated. To maintain a taut, even film, the painter must work in continuous zones, following the "wet-on-wet" technique. On frames or panelled doors, the order of application must be carefully planned: internal mouldings first, then panels, then horizontal rails, then vertical stiles.

Managing defects: correcting late exudations and film defects

On a renovation or new-finish construction site, the reappearance of yellowish stains or the localised detachment of the lacquer on a resinous knot is the most frequent defect after handover. When the exudation breaks through the film during use, applying an additional finish coat directly has no effect: the resin continues to migrate through the solvents or the water phase. The corrective treatment requires a targeted redo of the base.

  1. Mechanical stripping of the knotRemove the failed system with a scraper or P80 grit abrasive paper down to bare wood. Crystallise and scrape off the resin runs with a heat gun at moderate temperature, without charring the wood fibres.
  2. Local insulation with cationic blocker or shellacDegrease with a suitable solvent, then apply two crossed coats of a barrier insulating primer based on alcohol-based shellac or cationic resin, allowing full drying time between each coat to permanently seal the resin canals.
  3. Filler patching and surfacingFill the resulting depression with an oil-based or synthetic paintable filler. Sand with grit P240 to restore the perfect continuity of the surface plane before repainting.
  4. Blended finishApply an insulating intermediate coat, then re-lacquer the woodwork element up to a sharp edge or a recessed joint to eliminate any visible demarcation.

The joint inspection record of a visible lap mark or yellowing requires distinguishing the painter's responsibility from the initial condition of the substrate. However, failing to use a blocking primer on a resinous wood species systematically engages the applicator's liability with regard to the choice of technical means prescribed by standard SIA 257.

Frequently asked questions

Why does resin pass through a white satin lacquer after several months?

Conifer resins and hardwood tannins contain natural solvents that slowly pass through conventional acrylic or alkyd binders under the effect of heat and ultraviolet light. In the absence of a specific knot and tannin blocker forming a film impermeable to fatty substances, the sap reaches the surface and yellows the white pigment of the lacquer.

How can roller marks be avoided on a door lacquered with a water-based lacquer?

Apply the lacquer using a short-pile microfibre sleeve of 5 to 6 mm, adjust the open time with the retarder recommended by the manufacturer and work in small zones without going back over the work. Application without lap marks requires cross-rolling quickly, then smoothing in the direction of the wood grain in a single continuous stroke.

Which abrasive should be used for sanding between lacquer coats according to standard SIA 257?

Standard SIA 257 requires a smooth surface finish free of roughness. Sanding between coats is carried out by hand with stearated abrasive paper of grit P240 to P320 or an ultra-fine abrasive pad. The aim is to break the raised fibres and dust grains without sanding through sharp edges, followed by meticulous dust removal with a vacuum cleaner and a soft cloth.

Can a resinous knot be blocked with a universal undercoat alone?

No. Ordinary universal primers are permeable to resin acids and terpenes. Durable blocking requires a barrier product formulated either with shellac in an alcohol phase or with cross-linking cationic polymers. Applying at least two coats on each knot before the general primer is essential to permanently neutralise migration under a light-coloured lacquer.

Texts and standards cited

  • SIA 257Quality requirements and execution rules for painting, varnishing and interior wall covering work

In the same section