Skip to content
Website
🧱 CFC 272Wall coverings: wallpaper and wall hangingsChapter 5 of 10 in the section

Stripping the old covering: steamer, fragile plaster substrate and residual adhesive

Removing old wallpaper from traditional plaster requires a strict balance between wetting and mechanical action. Misuse of the steam stripper softens the gypsum and destroys the bond of the plaster to its substrate. This chapter details the preliminary diagnosis, the setting of the steam time, the techniques for protecting the substrate and the complete cleaning of paste residues.

Key takeaways

  • The initial sounding identifies the hollow areas of the plaster before any moisture is applied to the wall.
  • Exposure to steam never exceeds eight consecutive seconds, to avoid loss of cohesion of the gypsum.
  • The painter stops all manual pulling as soon as the substrate starts to disintegrate under the scraper.
  • The final washing of the adhesive residues ensures adhesion without soaking the plaster render rehydrated by the operation.

Assessing the substrate and dosing the steam to protect the plaster render

Before any stripping work, the qualified painter draws up a methodical condition survey of the whole papered wall. Old renders in plaster of Paris or fat plaster, very common in the building stock of French-speaking Switzerland, are characterised by high porosity and extreme vulnerability to prolonged soaking. The preliminary check is carried out by acoustic sounding, tapping the handle of the spatula against the wall. A dull or hollow sound signals internal detachment between the render body and the masonry, or between two historic layers of plasterwork. Identifying these structural weaknesses determines the areas where any application of water and heat must be avoided or greatly reduced.

Preliminary diagnosis of the plaster substrate before stripping
Sign observed on the wallUnderlying conditionTechnical requirement
Dull sound or hollow ringDelamination of the old plaster renderExclude the thermal steamer, prefer fine wetting
Brownish halos or saltpetrePresence of moisture or residual saltsSuspend wetting and measure the humidity of the substrate
Vinyl or washable coveringWaterproof barrier blocking the steamScore with a spiked roller without marking the plaster render

The steam stripper produces saturating moisture combined with a high temperature close to one hundred degrees. While this process effectively dissolves synthetic or starch-based adhesives, it subjects the gypsum to damaging thermal shock. Under the combined effect of heat and water, the surface crystals of calcium sulphate dihydrate lose their molecular cohesion, turning the hard plaster surface into a muddy mass. The painter must therefore keep the diffusion plate moving continuously. The tool is never left pressed on a fixed point for more than five to eight seconds. If the paper remains stubborn, using a surfactant stripping product sprayed at low pressure is far safer than prolonged thermal insistence.

On doubtful substrates, the team leader always carries out a test area on a discreet part of the room. This trial patch validates how the substrate behaves under moisture. If the render film turns to emulsion under the fingernail after five seconds of steam, the steam stripper is banned from the construction site in favour of a gentle impregnation with lukewarm water containing a biodegradable wetting agent.

Mastering the stripping technique and removing adhesive residues without soaking

Mechanical detachment of the covering requires controlled handling and suitable tools so as not to gouge the soft plaster. The painter uses a stripping knife with a flexible stainless steel blade, the corners of which have been rounded beforehand with abrasive paper to avoid scoring the substrate. The blade slides under the paper at a grazing angle of attack, less than thirty degrees to the substrate. If the strip resists the push, or if chalky plaster particles stick to the back of the paper when it is pulled off, the painter stops all manual pulling. Forcing a strip that is still stuck tears off the skin of the plaster, causing unacceptable surface defects.

  1. Mechanical surface scoringOn a waterproof or vinyl paper, slit the top film with a spiked roller without applying excessive pressure, to protect the plaster render.
  2. Controlled wettingApply the steam briefly, or saturate the strip with a roller using a solution of lukewarm water and stripper, then wait ten minutes to let it take effect.
  3. Grazing knife glidePush the blade flat under the soaked paper; stop the movement as soon as abnormal resistance appears and re-wet the targeted area.
  4. Dissolving the paste residuesSpray soapy lukewarm water on the remaining adhesive traces to emulsify them without soaking the depth of the plaster body.
  5. Final cleaning and wipingScrape off the sticky material with a soft spatula, then wipe carefully with a wrung-out natural sponge, renewing the clean water in the rinsing buckets.

Complete removal of adhesive residues determines the success of all subsequent work. Cellulose adhesives and starch resins form a translucent film that reactivates on contact with the moisture of a paint or a new pasting, causing blistering or saponification of the finishes. To check that no adhesive remains, the painter runs a damp sponge over the dried wall: a slippery feel or white foam reveals undissolved starch. A final wash with a wrung-out natural sponge removes these deposits without saturating the rehydrated plaster with water, guaranteeing a clean, sound surface for the rest of the construction site works.

Skin of the plaster
Dense, smooth surface layer hardened during the trowelling of the original plaster render, very sensitive to prolonged moisture and essential for the hold of future coverings.

Initial condition survey and critical strength thresholds of the plaster

Before starting to strip an old wall hanging or wallpaper, the painter must carry out a methodical examination of the underlying substrate. In Swiss older buildings, smoothed plaster renders do not all have the mechanical cohesion required to withstand the combined action of hot water and heat under pressure. Sounding the wall makes it possible to locate detached or hollow-sounding areas, the possible presence of a lime paint layer or an intermediate distemper, and the degree of porosity of the substrate. This preliminary diagnosis delimits the tradesman's responsibility before the massive moisture input generated by the stripper.

  • Acoustic sounding with the handle of a spatula over all the walls to locate render blistering and detachments from the masonry substrate.
  • Cutting a test window of 50 by 50 centimetres in a discreet corner to check the adhesion of the wallpaper and the behaviour of the original adhesive.
  • Looking for traces of old water infiltration, halos or mould under the strips, indicating chemically degraded or disintegrated plaster.
  • Checking for old layers of oil or alkyd paint acting as a steam barrier and likely to peel off in whole sheets.
Diagnosis of plaster deterioration and conduct of steam stripping
Observed condition of the substrateVisual and mechanical signsReaction under steamPainter's adaptation measure
Dead or powdery plasterWhite dust when scraped, crumbly under the fingernailImmediate breakdown into soft paste under the plateProhibit steam; dry removal of the peelable film and very targeted dampening
Render with a hollow soundHollow sound on light impact, surface crackingThermal swelling and falling of render sheetsStop the stripping; report the defect for repair by the plasterer
Superficially burnt plasterYellow-brownish film, loss of surface hardnessTearing off of the finishing film when pulledHalve the heating time and work with a scraping knife
Sound, hard plaster substrateCompact surface, dull sound, resistance to punchingControlled softening of the adhesive without damaging the substrateNominal steam cycle, stopping as soon as the strip slides

Cleaning adhesive residues, drying and preparing the substrate

Once the wallpaper strips have been removed from the substrate, the painter is faced with residual layers of starch adhesive, methylcellulose or synthetic emulsions. Letting these residues dry without treatment inevitably leads to blistering or flaking of subsequent finishes, as the adhesive reactivates when a dispersion paint or a water-based primer is applied. However, removing these adhesives must not reintroduce litres of water into a plaster that has just been through the steam stripper.

  1. Mechanical scraping of smears without attacking the renderAs soon as the strip is removed, while the adhesive is still warm and viscous, gently scrape off the thick beads of adhesive with a wide spatula with rounded corners, without cutting into the still-softened plaster render.
  2. Washing with a wrung-out natural spongeWash the wall with lukewarm water containing a neutral detergent, using a natural sponge that is continuously rinsed and wrung out thoroughly, working from bottom to top to avoid runs that would hollow out the plaster.
  3. Rinsing and immediate wiping with a clothPass a clean cotton cloth immediately after the sponge to remove the emulsified adhesive film and absorb excess water before it enters the micropores of the render.
  4. Ventilation and control of evaporationEncourage natural cross-ventilation of the rooms to remove the ambient humidity, without using direct fan heaters that would cause sudden shrinkage and crazing of the plaster.

The touch test and the water-drop test make it possible to check that there is no sticky film at all on the surface after complete drying. The plaster must again be dry to the touch, a uniform matt white, and show no fluffing. If persistent traces of old vinyl or insoluble adhesives remain, fine sanding with dry abrasive of grit 120 or 150 is required on a perfectly hardened substrate, followed by meticulous dust removal before applying the fixing primer coat.

Failure of the substrate and handling of tear-offs during stripping

When steam passes through a low-permeability wallpaper and penetrates massively into an old plaster, the surface bond of the mortar breaks down. The first critical signal appears as a mottled swelling of the substrate: the film no longer comes off on its own, and the blade of the painter's knife takes off a chalky film or fragments of dead plaster. From that moment, the heat and moisture input must be stopped immediately on the bay concerned. Continuing to wet with steam turns the historic render into a paste without cohesion, which spreads the damage to the whole wall section.

  1. Stopping the pulling and immediate dryingStop all manual pulling on the strip as soon as the render underlayer sticks to the paper. Ventilate the room without direct forced hot air so that the plaster can evaporate its excess water without shrinkage cracking.
  2. Removal of residual adhesiveOnce the substrate is stabilised and dry to the touch, neutralise the remaining methylcellulose adhesive by light rubbing with a barely wrung-out viscose sponge, followed by immediate wiping with a dry cloth, never soaking the weakened area again.
  3. Consolidation and delimitation of servicesApply a solvent-based hardening impregnation primer to re-bind the powdery areas. If the detachments go beyond the simple spot filling assigned to the painter, notify the condition of the substrate to the site management in accordance with the requirements of standard SIA 118.

If the condition survey reveals structural loss of cohesion of the render over more than twenty per cent of the surface of a wall, the limit of the painter's preparatory work has been reached. In accordance with standard SIA 257, the painter rejects the substrate as it stands. Complete repair then falls to the plasterer, who alone is authorised to strip back and rebuild the base coats to the required tolerances.

Frequently asked questions

How should you react on the construction site if the steamer softens the plaster render in depth?

Switch off the appliance and remove the diffuser plate. Above all, do not scrape the softened area: hot plaster loses all mechanical strength under the spatula. Let the surface dry completely in the open air for at least twenty-four hours. Then test the surface cohesion by light scratching. If the material turns to powder or sounds hollow, applying a penetrating fixative or redoing the render is necessary before any further priming work.

What risks do cellulose adhesive remnants left on an old plaster pose?

Adhesive residues react on contact with the water contained in dispersion paints or new adhesives. This late soaking causes blisters, yellowish stains from organic matter rising to the surface, and detachment of the new covering for lack of direct grip. It is essential to remove these deposits by careful washing with a wrung-out lukewarm sponge, followed by quick rinsing and a visual check under raking light.

Why must the use of the stripping knife on soaked plaster be prohibited?

Wet plaster sees its surface hardness drop drastically. The metal blade of a knife or scraper goes straight into the body of the render instead of sliding under the adhesive. The painter digs deep furrows, tears the finishing layer and rips out whole pieces of substrate. The stripping tool must only act at a very flat tangential bevel, on a saturated paper but a still-firm substrate.

What waiting time should be observed between steam stripping and the application of a new wall covering?

Even if the surface seems dry to the touch after a few hours, old plaster stores moisture in depth. You should wait for complete drying of forty-eight to seventy-two hours in a properly ventilated and heated room. Any early sealing under a waterproof wallpaper promotes the growth of underlying mould and destroys the adhesion of the bonding system. A residual moisture check with a dielectric meter validates resumption.

Texts and standards cited

  • norme SIA 118General conditions for the execution of construction work and handling of notices of interruption or non-conformity
  • norme SIA 257Execution of painting and varnishing work, criteria for the condition of substrates and limits of the painter's services

In the same section