Key takeaways
- The epoxy primer tolerates a maximum residual moisture strictly defined by the manufacturer's technical data sheet.
- An epoxy barrier never blocks water ingress under hydrostatic pressure, nor residual shrinkage.
- Broadcasting to rejection with graded quartz ensures the mechanical bond of the subsequent finishing coat.
- The client's written agreement releases the contractor from pathologies linked to the forced drying of the substrate.
Conditions of use and technical limits of the moisture-barrier primer
On new-build or heavy-renovation construction sites subject to tight delivery deadlines, the natural drying of a mineral screed is often the bottleneck of the schedule. General contractors frequently demand early installation of floor coverings to free up the premises and allow the installation of light partitions or interior fittings. In this urgent configuration, the application of a specific two-component epoxy primer acts as a temporary or permanent vapour barrier. This chemical system creates a sealed screen that confines the residual water in the substrate, making it possible to apply a thin screed, a levelling compound or a synthetic covering without waiting for the structural work to dry completely.
Using such a barrier requires a strict distinction as to the origin of the water present in the floor. The system is effective only against the residual mixing water of a concrete slab or cement screed undergoing natural curing. The resins used, formulated solvent-free on the basis of epoxy-amine with a high crosslink density, are able to cure in contact with a damp substrate without emulsifying. They seal the network of capillary pores and prevent vapour pressure from damaging the surface layers. By contrast, the process is strictly prohibited on damp calcium sulphate screeds: the trapped water destroys the binder by dissolution and causes the formation of expansive ettringite, leading to complete detachment of the resin build-up.
Broadcasting-to-rejection protocol and contractual formalisation
The effectiveness of a moisture-barrier system depends on the intimate bond between the resin and the cementitious matrix. The mineral substrate must undergo careful mechanical preparation, carried out by steel-shot blasting or diamond grinding with continuous extraction, in order to remove the cement laitance and open the capillary pores. The painter checks the condition of the surface scrupulously: it may be matt-damp to the touch, but must show no free water droplets or stagnant liquid film. If surface condensation is visible, localised thermal drying or forced ventilation must precede application of the barrier resin.
- Diagnosis and mechanical preparationCarbide moisture check, opening of the pores by mechanical shot blasting and careful industrial dust removal to eliminate any trace of surface laitance.
- Application of the epoxy barrier primerPrecise mixing of the two components with a slow electric mixer and even spreading of the product with a notched squeegee, followed by de-aerating with a roller.
- Broadcasting to rejection with dry quartzImmediate scattering of fire-dried quartz sand, grain size 0.4 to 0.8 millimetre, onto the fresh resin until full saturation, leaving no shiny areas.
- Vacuuming and preparation of the bondAfter the resin has fully cured, sweep by hand and vacuum all loose grains so as to obtain a mechanical bonding bridge as rough as sandpaper.
| Type of substrate | Water content found | Technical feasibility | Application protocol |
|---|---|---|---|
| Cement screed | Moisture below 6 % by mass | Feasible with barrier resin | Shot blasting, primer in two coats, quartz broadcasting |
| Cement screed | Film of free water on the surface | Not permitted as it stands | Prior surface drying until a matt appearance |
| Calcium sulphate screed | Above the application threshold | Absolute technical prohibition | Stop work and continue natural drying |
| Raft without waterproof membrane | Moisture with negative pressure | Technically incompatible | Prior treatment with heavy waterproof tanking |
Working on a substrate that is still damp in order to meet the schedule changes the painter's usual conditions of execution. Under the Code of Obligations (CO) and standard SIA 118, the contractor must send a written notice of reservation to the site management. This document records the moisture values measured, describes the barrier system, prices the surcharge for the primer and the broadcasting to rejection, and recalls the risks excluded from the warranty, in particular cracking linked to screed shrinkage. Application may start only after a written agreement has been signed by the client, expressly validating this derogating solution and releasing the company from the associated structural defects.
Admissible moisture thresholds and incompatible diagnoses
The application of an epoxy system acting as a moisture barrier meets only the requirements of a tight schedule on a new screed. In no case does this device turn a structurally unsuitable substrate into a sound base. It temporarily neutralises the diffusion of water vapour resulting from the natural drying of the concrete or cement screed, in order to allow a finishing coat to be applied without waiting the months required to reach the reference dryness. However, this technical solution has a measured tolerance and is not applied without rigorous quantitative checking.
The applicator painter must distinguish mixing water that is evaporating from continuous ingress of liquid water. Special solvent-free epoxy resins, emulsified or tolerant of damp substrates, block capillary water vapour, but inevitably fail under positive or negative hydrostatic pressure. A slab on ground without a waterproofing barrier compliant with the rules of the art of structural work, a failed basement tanking or lateral infiltration cause osmotic pressures that the resin film cannot withstand in the long term.
| Origin of the moisture | Manifestation on the substrate | Admissibility of the barrier | Consequence if application is forced |
|---|---|---|---|
| Bleed water / drying of cement screed | Matt surface, no film of free water, level below the technical threshold | Permitted with specific primer in two crossed coats | Controlled diffusion, mechanical adhesion maintained |
| Continuous capillary rise from groundwater | Constant moisture with no decrease over time, basement slab | Prohibited without prior tanking or structural waterproofing | Osmotic blistering, detachment in whole sheets in the medium term |
| Direct hydrostatic water pressure | Active seepage, localised shine, re-emergence through cracking | Formally excluded | Immediate bond failure, hydraulic delamination under the primer |
| Surface condensation linked to the dew point | Droplets of condensed water on the surface as the air warms up | Deferred until the air and temperature conditions are restored | Surface carbonation, carbamation of the resin, chalking |
Bonding broadcast and contractual transfer of responsibilities
The interposition of a sealed epoxy barrier creates an interface highly stressed by shear forces and by the shrinkage of the finishing system. The barrier resin, applied in two crossed coats at a total of at least 500 to 600 g/m², must imperatively receive a broadcast to rejection on its last coat while still fresh. Without this operation, the hardened surface would present a smooth glaze totally incompatible with the mechanical bond of a self-levelling compound or a trafficable polyurethane resin.
- Application of the closing coatApply the second coat of solvent-free epoxy resin with a roller or notched squeegee, ensuring absolute continuity of the film, without micro-bubbles or gaps at the edges and around duct penetrations.
- Spreading graded quartz to rejectionBroadcast by hand or by machine oven-dried quartz sand, grain size 0.4 to 0.8 mm (or 0.7 to 1.2 mm depending on the thickness of the following levelling compound), directly into the fresh film until completely saturated. No shiny spot of resin must remain visible.
- Vacuuming of the surplus after polymerisationAfter complete curing according to the manufacturer's instructions, remove the excess loose quartz by careful sweeping then high-suction industrial vacuuming, to obtain a perfectly anchored mineral key.
Using an epoxy barrier to shorten the intervention schedule is a derogation from the standard drying-wait processes defined in the standards of the Swiss Society of Engineers and Architects applicable to floor coverings. The verbal agreement of the site management in no way protects the painter-craftsman in the event of later damage.
By including this written agreement in the construction site file, the site manager formally records that the service is a technical supplement intended to compress the execution times. This traceability protects the company against claims relating to possible hygrometric deformations of the underlying screed during its deferred curing.
Managing defects: emergency measures for blistering and technical disputes
The appearance of osmotic blisters or delamination of the resin after application signals a failure of the moisture-barrier system. As soon as it is observed visually, the applicator painter records the damage with dated photographs and stops the finishing work. He sends a written report to the site management and the client. This step fixes the condition of the substrate before any aggravation or before the room is put into use.
The technical analysis on site begins with targeted core drilling with a hole punch to determine the failure plane. If the epoxy barrier tears off together with a film of surface laitance, the mechanical preparation by shot blasting or diamond grinding was insufficient. If the primer detaches cleanly with drops of water under liquid pressure or an alkaline seepage, the damage results from residual moisture outside tolerance or from continuous hydrostatic pressure. To objectify the remaining adhesion before any repair, a pull-off test with bonded dollies confirms whether the surface strength reaches at least 1.5 megapascals.
The repair requires complete stripping of the damaged area by planing or heavy shot blasting in order to remove the contaminated resin and the disintegrated cementitious matrix. After industrial vacuuming, a new calcium carbide measurement must be carried out jointly with the site management to requalify the substrate. If the screed still has a moisture content by mass incompatible with the manufacturer's limits, the company must suspend the work until natural drying or require active technical drying to be set up under the responsibility of the site management.
Contractually, under the rules of standard SIA 118, the traceability of earlier agreements determines who bears the financial cost. If the early application on a damp substrate was made on written order of the site management, accompanied by the applicator's customary reservations and the client's validated agreement, the cost of the stripping and repair work cannot be charged to the painter. In the absence of these written documents, the contractor alone bears the risk of having covered a non-compliant substrate.
Frequently asked questions
What to do if the client refuses to sign the written release?
If the client or their representative refuses to sign the written agreement and the derogating protocol, the painting company must refuse to apply the system and give notice of stoppage of operations on the floor. Application on a screed that is too damp without a formalised agreement transfers full responsibility for future defects to the applicator. The construction site must remain on hold until the residual moisture level reaches the standard admissibility threshold of the screed.
Why is broadcasting to rejection essential on the epoxy barrier?
Cured epoxy resin has a closed, smooth, non-porous surface to which no cementitious levelling compound or finishing coat can adhere mechanically. Broadcasting to rejection with oven-dried quartz sand creates the bonding roughness that is essential. After the resin has hardened and all non-adhering grains have been completely vacuumed, the resulting profile guarantees a durable mechanical bond without risk of later delamination of the levelling layers.
Can an epoxy barrier block water rising under continuous pressure?
No. A special epoxy barrier blocks only the residual mixing moisture trapped in the slab or the screed while drying. It in no way replaces watertight tanking or a waterproofing barrier against liquid water ingress under pressure, such as groundwater or lateral basement infiltration. Faced with active negative hydrostatic pressure, the epoxy film will inevitably blister under the effect of osmotic forces.
What is the maximum waiting time before covering the broadcast quartz?
The levelling compound or floor covering should ideally be applied within twenty-four to forty-eight hours after vacuuming the excess sand. Prolonged exposure to construction site dust, to the passage of other trades or to greasy contamination compromises the adhesion of the finishing system. If the floor remains uncovered for more than a few days, high-pressure cleaning or re-priming with an appropriate adhesion primer becomes essential before work resumes.
Texts and standards cited
- norme SIA 118General conditions for the execution of construction work
