Key takeaways
- The window-to-masonry junction requires three distinct barriers with vapour permeability increasing towards the outside.
- Expanding foam provides the central thermal and acoustic insulation but does not guarantee any lasting airtightness.
- The interior tape prevents warm, humid air from the room from entering the joint.
- The exterior membrane protects against driving rain while allowing residual moisture from the structural work to escape.
Physical principle of the triple seal and rejection of polyurethane foam as the sole barrier
On renovation and new-build construction sites in French-speaking Switzerland, there is still a temptation to inject single-component polyurethane foam into the gap between the window frame and the masonry reveal, trim off the surplus and then apply a simple sealant or smoothing render. This practice is a major non-conformity under SIA 331 (Windows and French windows). Expanding foam, whether open-cell or closed-cell, provides thermal sealing and contributes to sound insulation, but it has no certified long-term resistance to differential air pressure. Under the dimensional changes of the frame caused by thermal loading, the foam tears, loses adhesion to mineral substrates and undergoes irreversible degradation from ultraviolet radiation at its perimeter.
Building physics imposes the fundamental rule: "more airtight on the inside than on the outside". The connection joint must work as a complete system made up of three independent, complementary levels. The central plane must remain perfectly dry to keep its insulating capacity, which means preventing moisture from entering from the inside while offering an escape route to the outside for any accidental moisture.
| Functional plane | Main role | Required physical property | Typical materials |
|---|---|---|---|
| Interior (warm side) | Airtightness and vapour tightness | High Sd value (vapour retarder or vapour barrier) | Airtight adhesive tape, plasterable butyl tape, continuous hybrid polymer sealant |
| Central (core) | Thermal and acoustic insulation | Low thermal conductivity (lambda), absorption of movement | Compressed mineral wool, special elastic polyurethane joint foam, PE backing rod |
| Exterior (cold side) | Tightness against driving rain and wind | Open to water vapour diffusion (low Sd value) | Impregnated pre-compressed sealing tape (class 1), self-adhesive vapour-permeable membrane |
Order of work and rigorous installation of the three layers on the masonry reveal
The junction work must start before the frame is finally fixed in the opening. If the installer waits until the window is mechanically screwed in before dealing with the sealing, the hidden faces of the frame become inaccessible, which inevitably leads to discontinuities in the corners. Preparing the masonry surfaces is an essential prerequisite: concrete or calcium-silicate brick surfaces must be free of dust, laitance, frost and grease. On raw masonry of hollow clay brick or aerated concrete, a prior levelling coat of levelling mortar is required to guarantee a straight bonding plane.
- Pre-equipping the window in the workshop or on the groundBond the airtight tape around the interior perimeter of the frame profile, and the vapour-permeable membrane or pre-compressed tape on the exterior edge. Leave slack loops at the four corners to absorb differential movement without tearing the adhesive films.
- Positioning, wedging and mechanical fixingSet the window on rigid, rot-proof setting blocks. Adjust level, plumb and squareness. Anchor the frame mechanically into the masonry using frame screws without plugs or fixing brackets suited to wind and safety loads.
- Injecting or inserting the central insulation materialFill the peripheral space between the frame and the structural work over the full depth of the profile. When using elastic expanding foam, slightly dampen the mineral substrates to ensure uniform curing without hollow cavities, or insert mineral wool without compressing it excessively, to preserve its thermal resistance.
- Closing and pressing down the interior airtight barrierApply a bonding primer to the masonry reveal if the substrate is dusty or porous. Fold the airtight tape on the interior side back onto the masonry reveal, then press it down firmly with a pressure roller to eliminate any fold or air pocket.
- Exterior connection and weather protectionFix the vapour-open membrane to the exterior masonry before the external insulation or render is applied. When using a pre-compressed tape, check that its decompression rate matches the actual width of the joint so that it resists driving rain.
The site manager must ensure that the data sheets of the three selected products show full chemical compatibility, in particular between the acrylic adhesives of the membranes and the sealants or polyurethane foams. At acceptance of the work, the check is made visually for flatness and adhesion of the tapes before they are covered by the plasterers and painters, and may include a fan depressurisation test to confirm the absence of stray air leaks.
Technical coordination and interfaces of the three barriers according to SIA 331
The success of the perimeter sealing depends on strict compliance with the gradation of permeance between the inside and the outside. According to the rules of good practice set out in SIA 331 for exterior windows and doors, the interior barrier must have a vapour diffusion resistance clearly higher than that of the exterior barrier. This fundamental principle prevents interstitial moisture from accumulating at the core of the connection joint, thereby guaranteeing the integrity of the work against climatic stresses and temperature differences.
The connection of the frame to the structural work must be designed to remain airtight on the room side and permeable to water vapour on the exterior side, while ensuring tightness against driving rain.
norme SIA 331
In the fitter's practice, the airtight tape on the interior side is bonded continuously around the perimeter of the subframe or frame before it is inserted into the opening. The masonry, clay brick or concrete substrate requires a dust-free surface, free of laitance or formwork release oil, treated with a suitable bonding primer if necessary. This continuous layer forms the building's primary airtightness line, which is essential to meet thermal requirements without uncontrolled air losses.
| Barrier level | Main component | Required physical property | Mechanical and thermal role |
|---|---|---|---|
| Interior | Airtight tape or adhesive vapour-barrier membrane | High sd value (tight against air flow and vapour) | Prevents warm, humid room air from penetrating the gap |
| Central | Insulating fill (compressed mineral wool or elastic polyurethane foam) | Low thermal conductivity, resilience to movement | Provides continuous thermal and acoustic insulation between reveal and frame |
| Exterior | Vapour-open tape or impregnated pre-compressed tape | Low sd value, tightness against driving rain | Barrier against wind and water while allowing residual condensation to escape |
Installing the central fill and the vapour-open barrier
The central insulating fill serves a purely thermal and acoustic function. Whether it is made of mineral wool carefully inserted without excessive compression or of a certified elastic single-component polyurethane foam, it is in no case a sealing barrier. The facade installer takes care to dose the injection so as to fill the space uniformly without exerting lateral pressure that could bow the frame uprights, maintaining a perimeter gap calibrated with rot-proof spacer blocks.
On the exterior side, the vapour-open tape acts as a shield against the weather while letting the joint breathe. If an impregnated pre-compressed tape is used, its decompression must be controlled according to the temperature conditions on the construction site. The sealing must be able to withstand dynamic wind pressures without detaching from the raw masonry reveal or the base render.
- Preparation and adhesion primerClean the masonry reveals with a wire brush. Apply an impregnating primer to porous or chalky substrates to ensure continuous adhesion of the interior and exterior self-adhesive tapes.
- Mechanical fixing and wedging of the windowPosition the frame with lateral and bearing adjustment wedges. Anchor the frame mechanically into the structural work with plugless frame screws, without deforming the profile or compromising the position of the tapes already pressed down.
- Injecting the central insulating fillInject the flexible insulation foam or pack the insulating wool continuously into the central cavity, taking care to leave no thermal break or empty air pocket along the reveals and under the sill.
- Final connection of the sealsFold and press down the airtight tape onto the interior reveal. On the exterior, check that the vapour-permeable tape is properly closed under the sill flashings and at the masonry jambs.
Handling sealing non-conformities and reworking the junction
On site, finding a window installed with a simple injection of polyurethane foam and no perimeter membranes is a clear execution defect. The foam provides neither airtightness nor protection against driving rain. In this situation, the site manager must immediately suspend the interior lining and exterior rendering work and start a rework that complies with SIA 331.
- Diagnosis and opening up the jointCheck the alignment of the frame and cut back the flush foam to a minimum depth of 15 to 20 mm on both sides of the gap. Remove dust from the masonry and eliminate any laitance with a wire brush.
- Restoring the interior barrierApply an adhesion primer to the dry mineral reveal. Install the airtight tape on the interior side, pressing it down carefully onto the frame and the opening, with an expansion loop to absorb movement of the structure.
- Checking the insulating layer and closing the exteriorCheck the continuity of the central insulating fill, avoiding residual cavities. Install the vapour-open tape on the exterior side, bonded continuously to the frame and the structural work, to ensure vapour escapes to the outside.
The client may exercise their rights in the event of defects in the work under the Code of Obligations (CO), by requiring complete reworking of the sealing system at the contractor's expense. Under art. 365 CO, the contractor is responsible for the good quality of the material they supply. In addition, under art. 368 CO, the client may demand rectification where the work is defective. Rework from the outside beneath an external thermal insulation system requires careful removal of the reveal elements in order to restore the decreasing permeance without damaging the profile.
Frequently asked questions
Can an elastic expanding foam be used as a complete replacement for the sealing tapes?
No. Even if labelled elastic or acoustic, a polyurethane foam is never an airtight or driving-rain-tight barrier. It only provides the central insulating fill of the joint. According to SIA 331, the work imperatively requires an airtight tape on the interior side and a vapour-open tape on the exterior side. Neglecting these layers inevitably leads to infiltration and destructive condensation.
How should the lower junction at the window sill flashing be treated?
The metal flashing does not replace the sealing under the sill. A flexible sealing membrane or a preformed strip must be applied under the frame, bonded in a trough shape onto the masonry with watertight upturns at the sides of at least 20 mm. This second drainage barrier directs any infiltration or condensation water passing under the sill to the outside, while keeping the underlying thermal insulation dry.
Does the multifunction pre-compressed tape replace the system of three separate layers?
Yes, provided that a certified three-zone impregnated tape meeting the requirements of SIA 331 is chosen. The interior face is designed to be more vapour-tight than the exterior face. It requires a perfectly straight, parallel and dust-free masonry reveal. If the dimensional tolerances of the opening exceed the nominal compression range of the tape, the system loses its tightness and must be rejected.
What should be done if the reveal has irregularities or cavities before the tapes are installed?
It is forbidden to bond adhesive tapes directly onto irregular or dusty raw masonry. The installer must have a fine levelling coat or a mortar smoothing strip applied to obtain a flat substrate. Before the airtight tape on the interior side or the exterior membrane is applied, a bonding primer suited to the mineral substrate must be applied to guarantee permanent adhesion of the adhesives.
Texts and standards cited
- norme SIA 331Windows and French windows: requirements for performance, tightness and installation
- CO art. 365Material and ground: contractor's responsibility for the material supplied and duty to notify in the event of a defect compromising execution
- CO art. 368Client's rights in the event of defects in the work: rectification, price reduction, rescission or damages
