Skip to content
Website
🧱 CFC 221External insulation and renderChapter 5 of 10 in the section

Finish: grain, colour and minimum light reflectance value on insulation

This chapter gives you the selection rules for the finishing render on external thermal insulation. You will learn how to calculate the permissible light reflectance value, how to prevent thermal-stress cracks caused by dark colours, how to have a reference sample approved on the construction site and how to manage your batches to eliminate any shade variation.

Key takeaways

  • A light reflectance value below the recommended threshold leads to destructive expansion stresses.
  • The insulation blocks heat dissipation towards the supporting wall and overheats the thin finishing render.
  • A sample on the façade remains the only reliable method of validating the colour under real natural light.
  • Cross-mixing buckets from different batches guarantees a perfectly uniform colour across a full panel.

Light reflectance value and thermal stresses on insulation

On external thermal insulation, the thin finishing render layer is only a few millimetres thick. Unlike traditional solid masonry in brick or concrete, which absorbs and then spreads the heat into the structural work, the insulation panel in expanded polystyrene or mineral wool acts as a barrier. All of the solar energy absorbed by the surface stays concentrated in the reinforced build-up made up of the base coat and the mineral, siloxane or synthetic render. When the surface temperature rises sharply in summer and then drops during a thunderstorm shower, the thermal gradient generates considerable stresses between the reinforcing mesh and the finish.

Light reflectance value (Y value or HBW)
The percentage of visible light reflected by a coloured surface compared with a perfect white calibrated at 100%. A low value indicates a dark colour that absorbs a large share of solar radiation.

The expansion of a dark colour stresses the system to its elastic limits. Under direct midsummer sun, the surface of a white or very light render with a value above 70% rarely exceeds 40 °C. Conversely, an anthracite or chocolate colour whose value falls below 20% commonly rises above 70 °C on the south or west façade. These temperature differences over a day-night cycle cause micro-cracks at the mesh overlaps, surface crazing of the binder and, in the long run, shearing of the base coat at the edges of the insulation panels.

Thermal behaviour of thin render colours on external thermal insulation
Value range (HBW)Estimated summer heatingMechanical risk on insulationApplication measures
Above 30%From 35 °C to 50 °CNegligible under normal conditionsStandard application with conventional glass-fibre mesh
From 20% to 29%From 50 °C to 65 °CModerate (stresses at edges and lintels)Thicker base coat or cold pigments with near-infrared reflectance
Below 20%Above 70 °CHigh (cracks, detachment, blistering)Double mesh, fibre-reinforced mortar or specific manufacturer technical approval

Grain control, validation on a sample and monitoring of mixes

Roughness and grain size directly change the perceived colour. Between a 3 mm scraped (ribbed) render and a 1.5 mm fine floated render made with the same pigment dosage, the more textured surface systematically looks darker because of the micro-shadows cast by the grains. For this reason, the client's final choice must never be based solely on a paper colour chart of a few square centimetres or on a rigid sample prepared in the factory under artificial light.

If the client demands a specific colour that involves technical constraints, the contractor states the necessary reservations in accordance with the duty to notify provided for in art. 365 CO para. 3, in order to document the risks of overheating or shade variation before final application.

  1. Making a test panel in situApply the chosen finishing render to a real area of at least 1 to 2 m², directly on the external thermal insulation system being installed. Choose a representative area receiving raking light.
  2. Complete drying before assessmentWait for the mixing water to evaporate completely and for the binder to set, over several working days. The colour of a fresh, wet render is always two to three shades lighter than the stabilised dry result.
  3. Joint approval of the resultExamine the test panel with site management under different lighting conditions (morning and afternoon), then record the conformity of the grain and colour in the site diary.
  4. Checking batch numbersOn delivery to the construction site, check that all buckets or bags intended for one continuous façade carry strictly the same colour batch number, in order to rule out variations in intensity.
  5. Cross-mixing during workPlan to systematically combine the remaining third of the previous bucket with the freshly opened bucket in a large mixing container before application with the stainless-steel float.

Thermal behaviour and reflectance thresholds on external thermal insulation

Applying a finishing render on an external thermal insulation system (EPS, stone wool or polyurethane) imposes direct physical stresses on the reinforced build-up. The insulation blocks the heat flows coming from inside the building but also isolates the render from the solid substrate. In summer, under direct radiation, the solar energy absorbed by the surface stays concentrated in the thickness of the reinforced base coat (generally 3 to 5 mm) and of the finishing render. A dark colour accumulates heat and can bring the surface temperature above 70 °C in full sun, before a summer storm causes a violent thermal shock by lowering this temperature by 40 °C within a few minutes.

This temperature range generates an expansion of a dark colour far exceeding the elastic elongation capacity of common mineral mortars. The resulting shear stresses act at the interface between the insulation and the base coat, causing curling of the insulation panels and spider-web micro-cracks in the facing render. The minimum light reflectance value (LRV, or HBW in German) describes the amount of visible light reflected by a colour compared with perfect white (100%) and absolute black (0%).

Permissible thresholds and thermo-mechanical stresses according to the light reflectance value of the render
LRV range (HBW)Estimated summer heatingRequirement for the reinforcing mortarFeasibility on external thermal insulation
LRV ≥ 25%Moderate (< 55 °C)Standard fibre-reinforced bedding mortar, standard meshStandard application without particular restriction
20% ≤ LRV < 25%High (55 to 65 °C)Reinforced base coat or minimum thickness of 5 mmTolerated with stable insulation and mesh laid without creases
LRV < 20%Critical (> 65 to 75 °C)Organic base coat without cement, double mesh mandatoryProhibited in standard application; requires cold pigments (TSR)

For deep colours with a value below the 20% threshold, measuring the LRV alone is no longer sufficient. Façade contractors must require the total solar reflectance (TSR) value from the supplier. Unlike the LRV, which quantifies only the visible spectrum, the TSR includes the infrared radiation responsible for the rise in temperature. The use of so-called "cold" pigments thus makes it possible to keep a visually dark colour while rejecting up to 30% more invisible thermal energy, limiting the thermal fatigue of the build-up.

In-situ validation, scale effect and rigorous management of mixes

The selection of an external render can never be limited to examining a cardboard colour chart in the architect's office or an A4 demonstration card. The surface effect radically changes the final appearance. On a whole façade exposed to raking light, a rustic or scraped (ribbed) grain with a grain size of 2.0 mm creates self-shadowed areas that darken the overall tone by one to two shades compared with a smooth card. Conversely, a very fine floated render of 1.0 mm diffuses light uniformly but reveals the slightest flatness defect in the substrate.

Producing a reference sample on site is a mandatory contractual milestone before any bulk order of material. This sample must measure at least 1 m² and be applied directly to the real substrate, with the pigmented primer coat and the texturing technique that will be used on the construction site. In accordance with the Code of Obligations, the contractor is responsible for the conformity of the material it applies, in line with the rules of its trade. The sample must dry for at least 72 hours to stabilise its pigments and its matt finish before joint approval by site management and the client.

  1. Checking batch numbers on deliveryCheck the factory reference, the colour code and the production batch number on each bucket or bag. A single façade or a continuous section bounded by sharp edges must absolutely be covered with the same production batch to avoid shade differences.
  2. Cross-mixing and homogenisationWhen the quantities require two different batches to be used on the same building, reserve each batch for a separate façade divided by an internal or external corner. If a full section requires a mix, blend in the tub by re-incorporating a third of the previous bucket into each new mix.
  3. Continuous "wet-on-wet" applicationDeploy a sufficient number of workers on the scaffolding to cover the full height of the façade in successive levels without marking the joints. Application must be carried out at a steady rate, never letting the render dry out at floor junctions.

Batch homogeneity concerns not only the raw colour but also the rheology of the paste. In the case of a mineral render with hydraulic binders mixed on site, the accuracy of the water dosage determines the final colour: excess water lightens the colour by migration of lime laitance to the surface, while a lack of water accelerates setting and densifies the pigmentation. For ready-to-use organic renders (silicone or silicate resins), no addition of water not prescribed by the technical data sheet is to be tolerated on the working platform.

Handling non-conformities: thermal cracks, shade variation and remedies on site

When the application of a finishing render reveals an aesthetic or structural defect, the façade contractor must intervene before complete drying or acceptance of the work. Two pathologies dominate: early cracking linked to thermal stresses and variations in appearance between scaffolding lifts. Using a coating whose minimum light reflectance value required by the manufacturer has not been respected leads to surface overheating in full sun. The expansion of a dark colour subjects the reinforcing layer to abrupt heating and cooling cycles, causing linear micro-cracks and then partial detachment of the levelling coat.

  1. Recording the finding and stopping the liftAs soon as shade variation appears, stop floating at a sharp edge or a movement joint to avoid joints in the middle of a section.
  2. Checking suppliesCheck the homogeneity of the product batches and the production numbers on the drums. If different mixes are being used side by side, immediately carry out cross-premixing in the tub.
  3. Contractual regularisationIn accordance with art. 365 CO, if another circumstance jeopardises the proper or timely execution of the work, the contractor informs the client.

If the substrate proves to be cracked as a result of a colour that is too dark, imposed without specific reinforced mesh, the repair requires sanding the textured finish, laying a second layer of high-density glass-fibre mesh, and then applying a levelling paint with high spectral reflectance to lower the overall thermal load of the insulation build-up.

Frequently asked questions

What should be done if the architect demands a colour whose light reflectance value is below the limit permitted on EPS?

The contractor must give formal written notice of refusal before the products are ordered. A dark colour pushes the render above 60 °C under direct summer exposure. On expanded polystyrene, this thermal shock softens the panel and shears the reinforcement. To keep this colour, the insulation must be replaced by mineral wool or a reinforced fibre base coat approved by the system manufacturer must be specified.

How can visible joint marks between two scaffolding levels be avoided on a scraped render?

The application team must be sized according to the height of the façade section: at least one applicator per floor level. Floating is carried out continuously, wet-on-wet, without interruption along the uprights. The junction zones must be offset away from direct lines of sight, the ground under the scaffolding must be wetted in hot weather and the façade must be protected from the wind with micro-perforated nets.

Why is colour shade variation observed on a façade done with the same render reference?

Shade variation frequently results from mixing buckets from different production runs. Even when calibrated in the factory, pigment pastes undergo tiny variations in moisture and dosage. In addition, floating on a render that is too dry or a difference in wind exposure changes the evaporation of the residual water, which whitens the binding resins and locally changes the refraction of light.

What is the legal value of a colour sample supplied by the manufacturer as a cardboard card?

The cardboard card is merely a colour indicator with no contractual value for the acceptance of a mineral or synthetic render. The texture of paper does not absorb light like a floated grain of 1.5 or 2 millimetres. Only a test panel of at least one square metre made on the façade itself, dried and jointly signed, formally binds the company and site management.

Texts and standards cited

  • CO art. 365material and ground: the contractor is responsible for the good quality of the material it supplies; if the material supplied by the client or the ground designated by the client is found to be defective, or if another circumstance jeopardises the proper or timely execution of the work, the contractor must immediately inform the client, failing which it bears the consequences (para. 3)

In the same section