Skip to content
Website
🧱 CFC 221Blinds, shutters and solar protectionChapter 8 of 10 in the section

Fixed sunshade: orientation, overhang and winter solar gain

This chapter provides the geometric and fastening rules for installing an effective fixed sunshade. You will learn how to calculate the required overhang based on the solar path between solstices, dimension anchorages against wind uplift forces, and organise cleaning operations without deforming the structure.

Key takeaways

  • The south-facing horizontal overhang blocks the summer zenith and allows low winter rays to penetrate.
  • East and west façades require vertical louvres due to very low solar angles.
  • Fasteners pass through the insulation onto thermal brackets capable of absorbing wind pressure and uplift.
  • Maintenance access must distinguish an inaccessible decorative louvre from a trafficable deck secured against falls.

Calculation of shading geometry between summer and winter solstices

The effectiveness of a fixed sunshade is based on the variation of the sun's height throughout the year. In French-speaking Switzerland, at a latitude of approximately 46.5 degrees north, the sun reaches its zenith at around 67 degrees above the horizon at the summer solstice, whilst it does not exceed 20 degrees at the winter solstice at solar noon. This angular difference of over 45 degrees makes it possible to design purely passive shading without motorized mechanisms, ensuring summer thermal protection whilst allowing free passive solar gains during the cold season.

Shading angle (solar profile)
Angle formed by the horizontal plane and the line joining the outermost edge of the overhang to the bottom edge of the glazing. It determines the date from which the cast shadow covers the entirety of the glazed opening.

On a south-facing façade, the horizontal overhang represents the benchmark geometry. For a standard window with a height of 1500 mm and a typical spandrel, an overhang between 600 mm and 900 mm ensures full shading from direct radiation between early June and late August. Low winter rays pass entirely beneath the overhang to warm the internal slab. Conversely, applying this system to east- or west-facing façades is a major error: in the morning and late afternoon, the solar altitude drops below 30 degrees with a lateral angle of incidence that horizontal louvres cannot intercept without an excessive overhang.

Performance of fixed sunshades according to orientation in Switzerland
OrientationOptimal layoutUseful solar altitudeWinter solar penetration
South (± 15°)Horizontal overhang with profiled louvresHigh (55° to 67° in summer)Maximum (rays below 25° unobstructed)
South-East / South-WestHorizontal louvres with side cheek platesMedium (40° to 55°)Good with partial clearance
East / WestFixed vertical louvres or brise-soleil screenLow (below 35°)None or very limited
NorthUnnecessary (solar shading superfluous)Diffuse radiation onlyNo direct solar gains

Aerodynamic load transfer, thermal-bridge-free anchoring, and maintenance

Under wind action, an external overhang behaves like an aircraft wing. It is subjected to alternating downward pressures from head-on gusts and strong upward suctions when wind rounds the building edge or sweeps up the façade. Mechanical fixings cannot merely support the self-weight of the aluminium or timber; they must resist dynamic uplift and overturning moments transmitted by the lever arm of the projection.

Where external thermal insulation composite systems (ETICS) or ventilated cladding are present, the façade installer must prohibit any direct clamping against compressible insulation. Loads are transferred to the solid reinforced concrete or sand-lime masonry substrate via thermally broken brackets or fibre-reinforced epoxy resin sleeves with stainless steel threaded rods. Fasteners pass through the insulation build-up to the structural work, with point thermal bridging broken by rigid, high-compressive-strength insulating shims.

Installation is carried out using strictly secured access equipment. As soon as the fall height exceeds 3 metres, OTConst art. 26 requires a façade scaffolding to perform marking, drilling, and bracket tightening without endangering the crew. On completed façades, future maintenance determines the choice of profiles: fixed louvres accumulate dust, droppings, and pollen, which reduce interior light and cause dark streaks on the glazing during rainfall. Unless the system includes a certified gantry track for window cleaning, louvres must have a minimum outward cross-fall of 2% to encourage self-cleaning and remain accessible from a mobile elevating work platform.

Lateral overhangs and geometric adaptation according to orientation

The effectiveness of a fixed sunshade does not depend solely on its projection depth directly above the opening. Across French-speaking Switzerland, at a latitude of approximately 46.2° to 47° North, the solar path describes a particularly wide arc at the equinoxes and during summer. An overhang aligned strictly with the window reveal width allows oblique morning solar radiation from 9:00 and late afternoon radiation from 15:00 to penetrate. Low-angle rays then strike the glazing directly from the sides, ruining indoor thermal comfort. To guarantee effective solar shading without relying on motorized secondary blinds, the horizontal projection must systematically extend laterally beyond the outer face of the window frame.

The performance of a fixed overhang varies radically according to the cardinal orientation of the façade. Whilst a due South orientation is the perfect configuration for a horizontal sunshade—high June sun being blocked whilst low December sun passes entirely beneath the structure—South-East and South-West orientations demand heightened vigilance. On these intermediate orientations, the sun is still relatively low on the horizon when facing the façade directly. An isolated horizontal overhang loses much of its utility if it is not combined with vertical side cheeks or specific angled louvres acting as deflectors.

Solar performance and recommended sizing of a fixed sunshade according to orientation
OrientationDominant solar angleDepth / glazing height ratioWinter performanceAdditional measures required
Due SouthHigh in summer (62° to 67°), very low in winter (17° to 22°)0.35 to 0.45Maximum passive solar gain at the December solsticeSimple lateral overhang of 30 cm on either side of the reveal
South-EastMedium to low in the morning, receding azimuth0.50 to 0.60Morning solar gains maintained, partial mid-season shadingVertical shading cheek on east side or louvres angled at 45°
South-WestMedium to low in the afternoon, coinciding with peak heat0.55 to 0.65Afternoon gains preserved but risk of late overheatingVertical cheek on west side essential to block low-angle sun
East / WestVery low on the horizon, almost horizontalNot applicable (ineffective)Full penetration but very low winter thermal gainsAvoid fixed horizontal overhangs; use vertical louvres instead

In mid-winter, a fixed sunshade does not penalise the building's cantonal energy balance. With the midday solar altitude barely exceeding 20° on the Swiss Plateau, the shadow cone cast by the overhang is thrown entirely above the upper head frame of the window. The entire daylight opening receives direct light flux, providing an essential passive thermal gain that limits demand on the heating system.

Aerodynamic load transfer and maintenance access requirements

Structurally, a sunshade overhang does not behave like a simple canopy supporting only its self-weight and the snow load specified by standard SIA 261. The governing action on the construction site remains uplift caused by ascending wind. The wedge effect created beneath the horizontal element by dynamic wind pressure compressed against the façade wall generates uplift stresses via suction on the upper face and pressure on the lower face. These cyclic loads require brackets capable of handling alternating bending without premature fatigue of the metal fixings.

Anchoring to the structural work requires penetrating the external thermal insulation build-up. The façade installer uses powder-coated steel or extruded aluminium brackets secured to the concrete by chemical anchors or expansion anchors conforming to technical approvals. Rigid thermal breaks made of compact polyurethane or glass-fibre-reinforced polyamide are inserted between the baseplate and the masonry structure to eliminate thermal bridges without crushing under tightening torque. Air- and rainwater-tightness is ensured by an EPDM collar or a perimeter sealing bead prior to installing the ventilated cladding.

Detailing must also integrate periodic maintenance of the building envelope. Aluminium or thermally modified wood louvres collect dust, pollen, and bird droppings that eventually soil the glazing below during rain events. OTConst art. 17 requires measures to ensure that workers are not endangered during work and at workstations. Brackets must be designed to allow easy passage of squeegees or telescopic poles from internal openings, unless an integrated maintenance grating is engineered to support the load of an operative tethered to a temporary lifeline.

  • Provide a clear gap of at least 80 mm between the rear of the first louvre and the glazing line for window cleaning.
  • Maintain a minimum 2% outward fall on solid profiles to prevent meltwater and silt ponding.
  • Record allowable loads on the as-built envelope drawings to explicitly prohibit direct foot traffic on lightweight louvres.
  • Facilitate individual removal of louvres using A4 stainless steel fasteners accessible from the underside in the event of hail damage.

Management of non-conformities: anchorage defects, abnormal deflection, and water ingress

On the construction site, defects affecting fixed sunshades primarily manifest through three critical symptoms: partial pull-out of fixings during severe wind events, significant residual deflection under snow loads, or moisture staining aligned with façade penetrations. When abnormal mechanical play appears on supporting arms or louvres twist, the assembly jeopardises the safety of persons below. The root cause almost always stems from a misunderstanding of the actual substrate compared to initial assumptions, such as aerated concrete mistaken for a reinforced wall or an underestimated insulation thickness distorting the lever arm.

  1. Immediate securing and diagnosisCordoning off the ground area, temporarily propping brackets exhibiting buckling or rotation, followed by targeted intrusive testing of the masonry to verify actual anchor embedment depth and sleeve capacity.
  2. Structural recalculation and reinforcementImmediate submission of pull-out survey data to the structural engineer to recalculate tension and shear forces according to current SIA standards, followed by replacement of threaded rods with high-strength chemical anchors and suitable injection mesh sleeves.
  3. Remediation of sealing interfacesReconstructing the weather-resistive barrier around baseplates using bonded EPDM membranes, followed by installing watertight thermoplastic shims providing a thermal break without crushing the render.

If the exposed substrate exhibits mechanical strength unsuitable for absorbing the torsional moment generated by the cantilever, the contractor refers to CO: when circumstances jeopardise the proper execution of the work, the contractor immediately informs the client. Work on the affected area is halted until an adapted fixing detail is approved. Under standard SIA 118, this formal notice prevents any subsequent dispute regarding engineering cost overruns or delivery delays.

Frequently asked questions

How can whistling in a fixed sunshade subjected to strong Bise gusts be eliminated?

This aeroacoustic phenomenon results from louvres aligning with wind direction, generating periodic vortex shedding on sharp edges. The solution consists of installing intermediate stiffeners to break the vibrational span of the profiles, or fitting leading edges with dedicated bevelled lips. Adding viscoelastic dampers at the bracket fixings also reduces transmission of acoustic vibrations to the building's structural work.

How can the cantilever of a solar overhang be reconciled with upper-floor window cleaning?

An overhang projecting more than 80 cm prevents the use of a window-cleaning pole from the inside. If the façade lacks a suspended cradle system, the sunshade louvres must be designed either as a trafficable grating capable of supporting maintenance walkway loads, or with removable sections that allow temporary maintenance access in compliance with safety regulations.

Is a horizontal sunshade still effective on a south-west-facing façade?

On a south-west orientation, the late-afternoon solar altitude becomes particularly low at the end of a summer day, rendering a horizontal overhang insufficient. Direct radiation penetrates sideways beneath the assembly. To maintain thermal comfort without excessively increasing the cantilever, the horizontal projection must be combined with closed vertical cheek plates or the louvres must be extended 30 to 50 cm beyond the outer edge of the glazing.

What solution should be used to penetrate rendered insulation without crushing it during tightening?

Clamping a baseplate directly onto the façade render compresses the insulation and damages the external weather-tightness. The façade installer must use heavy-duty dedicated fixing modules that incorporate a rigid composite cylinder screwed down to the load-bearing wall. The metal bracket comes into mechanical bearing against this support cylinder, ensuring effective tightening torque without exerting compressive stress on the insulation build-up.

Texts and standards cited

  • COmaterials and ground: the contractor is liable for the good quality of materials supplied; if materials supplied by the client or the ground designated by the client are found to be defective, or if any other circumstance compromises the proper or timely execution of the work, the contractor shall immediately inform the client, under penalty of bearing the consequences (para. 3)
  • norme SIA 118General conditions for construction work

In the same section