Skip to content
Website
🧱 CFC 221Measured performance and building envelope acceptanceChapter 7 of 10 in the section

Water ingress discovered after acceptance of the work: trace it to its origin before blaming a trade package

Water seen at a window reveal or at the foot of a ventilated cladding often originates several metres higher up. This chapter details the non-destructive investigation method using compartmentalised water spraying from the bottom up. You will learn to trace the real hydraulic path, to organise a joint expert inspection with site management and to record the technical facts before any destructive intervention.

Key takeaways

  • Systematic water testing is always carried out from the bottom up in order to isolate each level of facade waterproofing precisely.
  • Water often travels horizontally along flashings or drip edges before appearing in the interior rooms.
  • The SIA 118 standard governs the notification of defects during the two-year warranty period.
  • Any search for water ingress requires a written joint inspection record with site management before any dismantling.

Locating the hydraulic path through systematic zone-by-zone water testing

In a ventilated facade or around an external window frame installed in the reveal, the point where water ingress emerges almost never corresponds to its point of entry. Water enters under the effect of wind, gravity or capillarity, then travels along the substructure profiles, over the rainscreen membrane or through the joints of the perimeter insulation. It can slide horizontally for several metres over a flashing with insufficient fall or a fixing profile before crossing the interior waterproofing plane at a fixing screw or a sill-board junction. Immediately dismantling the cladding at the location of the interior stain destroys the evidence and prevents identification of the original failure. Only a rigorous method of simulating rainfall can isolate the exact origin of the defect.

  1. Visual inspection and placement of indicatorsMeasure the interior humidity with a contact hygrometer. Place blotting paper indicators or absorbent tape at the foot of the reveal and along the vapour barriers to detect the slightest droplet.
  2. Spraying the lower junctionFirst spray the sill, the lower flashing and the junction with the masonry at low pressure. Keep the surface regularly wetted for at least 15 minutes without spraying the side jambs.
  3. Spraying the middle sectionsTest the window frame jambs, the blind guide rails and the vertical joints of the adjoining cladding. Work over a height of 1 metre at a time, progressing towards the lintel.
  4. Spraying the lintel and upper sectionsApply water to the lintel, the blind box and the upper edges of the facade. If water appears only at this stage, the ingress comes from the upper barriers.
Control parameters for compartmentalised spray testing
Zone testedEquipment and pressureMinimum durationInterior observation points
Flashing and lower sillFlat-jet spray bar, low pressure (1 to 2 bar)15 to 20 minutesUnder the interior sill board, foot of the lining
Reveals and guide railsHand nozzle directed downwards at 45°15 minutes per sideLower corners of the frame, sealing strips
Lintel and blind boxPerforated spray bar, continuous flow20 minutesUnderside of the lintel, control penetrations
Cladding and rainscreen membrane jointsSpray lance with fluorescent tracer30 minutes per panelThermal insulation, bracket penetrations

Conducting the joint expert inspection under the SIA 118 standard

When water ingress occurs during the warranty period, the client's or site management's reflex is often to blame the window or lightweight facade contractor (CFC 221) directly. Under art. 367 CO, after delivery the client examines the condition of the work as soon as is practicable and notifies the contractor of any defects. However, where the contract incorporates the SIA 118 standard, a specific regime applies during the first two years: the client may assert defects discovered at any time during this notification period. This right does not relieve the parties of establishing the facts and their attribution jointly before undertaking remedial work.

  • The date, time and weather conditions recorded when the damage occurred.
  • The precise visual survey of the interior damp areas, with photographs and mapping on plan.
  • The water-testing protocol applied: flow rates, zones sprayed and observation durations.
  • The formal identification of the leak point and the trades concerned at the interfaces.
  • The signed agreement of all parties on the protective measures before dismantling.

A lightweight facade has many critical interfaces with the sheet-metal work, the roof waterproofing, the masonry and the solar protection. If zone-by-zone spraying shows that water enters through a defective junction belonging to another trade package, the joint inspection record clears the window installer or facade contractor of responsibility. Remedial work can only be demanded once the technical cause has been formally attributed, thus avoiding unjustified destructive interventions at the tradesperson's expense.

Diagnosing the hydraulic path in the ventilated facade assembly

Finding a damp patch on an interior reveal or a slab edge never allows you to immediately blame the window or the connection joint. In a ventilated facade or a lining with perimeter insulation, liquid water often enters several metres from where it re-emerges. Guided by the slope of an invisible drip edge, deflected by a poorly folded flashing or channelled along the substructure battens, the water follows an erratic path dictated by gravity, air pressure gradients and capillary forces.

To trace the hydraulic path without wrecking the exterior cladding, the facade contractor uses targeted investigation methods. Endoscopy with a flexible camera inserted through open cladding joints or low ventilation grilles makes it possible to view the condition of the rainscreen membrane, the presence of water pockets retained behind the thermal insulation and traces of run-off on the structural work. If a tracer fluid injection is required to confirm a path, the use of fluorescent tracers visible under ultraviolet light, with no corrosive or staining effect on interior finishes, remains mandatory.

Types of internal hydraulic paths and actual points of entry
Interior point of re-emergencePhysical path observedFrequent actual origin
Dripping at the window lintelVertical flow along the rear face of the insulation, held up on the upper transom of the subframeFaulty membrane junction under a parapet coping, or cladding fixing penetration upstream
Dampness on the interior window sill boardIngress under the exterior aluminium sill, lateral migration over the acoustic feltLeaking lateral sill end caps, or absence of a 20 mm watertight upstand under the profile
Stain at the foot of the wall adjacent to the window frameDrainage failure of the pressure-equalisation cavity, water channelled by the framework fixing angleUnderlying drip flashing interrupted or compressed against the thermal insulation without fall
Mould in the corner of an interior revealHumid air flowing from inside to outside combined with capillary return of wind-driven rainAirtightness strip not bridged to the vapour control layer, or penetration by a fixing bracket

Joint investigation and settlement of the defect under the warranty regime

As soon as a notice of defects reaches the company during the two-year warranty period defined by the SIA 118 standard, no major repair work may be undertaken without a formal summons to all the trades involved on the envelope. The interfaces between the external window work (CFC 221), the waterproofing junction and the masonry form a grey area where the first party to demolish the work destroys the material evidence that establishes responsibility for the defect.

Under art. 367 CO, after delivery the client examines the condition of the work as soon as is practicable and notifies the contractor of any defects; for a building work, the client has 60 days to notify them, and a shorter contractual period is void. Each party may also request an examination by experts. Where the contract is placed under the SIA 118 standard, defects may be notified at any time during the first two years of the warranty. To avoid any forfeiture of recourse actions between subcontractors or consultants, the overall limitation period for the client's rights in respect of defects in a building work remains governed by art. 371 CO, which provides a five-year period against the contractor, the architect or the engineer.

  1. Written summons to the siteSend a summons to a joint expert inspection to site management, the client and the representatives of the adjacent trades (waterproofers, sheet-metal workers, masons) with sufficient notice.
  2. Preliminary visual inspection without dismantlingObserve the condition of the facades in dry weather and record perimeter cracks, unauthorised silicone sealant patching or changes of use made since acceptance.
  3. Staged opening-up recorded in minutesRemove cladding boards, the sill support or reveal linings methodically and only in the presence of the parties. Photograph the moisture condition of successive layers.
  4. Drafting and signing the joint protocolDraw up a protocol on the spot recording the technical facts observed, the exact location of the failure in the waterproofing barrier and the parties' agreement on the origin of the defect before planning the repair.

Persistent disagreement and deadlock: formalising the technical impasse

When the systematic zone-by-zone spray protocol does not produce a consensus, or when another trade package disputes the water path through the wall, the situation on the construction site quickly freezes. Site management is often tempted to order immediate protective repairs, charging the costs automatically to the facade company under the two-year warranty of the SIA 118 standard. The contractor for lightweight facades or external window work must refuse any uncoordinated destructive intervention that would conceal the real source of the water path.

  1. Drawing up a record of technical disagreementAt the end of a disputed spray test, draw up on the spot a countersigned note detailing the zones sprayed, the flow rates applied, the observation times and the interior manifestations. State explicitly the differences of interpretation between trade packages.
  2. Requiring the involvement of a neutral expertPropose to the client the immediate use of a neutral expert from a recognised professional association or appointed by agreement between the parties, in accordance with the procedure provided for the examination of defects by third parties.
  3. Securing the evidence through a documented recordHave the exact condition of the premises recorded by a bailiff's report or high-definition photographic documentation including moisture gauge readings, before the dismantling of cladding or insulation elements destroys the hydraulic evidence.

Under art. 367 CO, each party has the right to request an examination of the work by independent experts. If site management persists in threatening substitute performance at the facade contractor's expense, the contractor formally notifies its objection by registered letter. It recalls the facts established during the joint investigation, confirms its availability to take part in the investigations of the appointed court or private expert, and reserves all its rights regarding the additional costs of downtime, scaffolding and engineering caused by unfounded accusations.

Frequently asked questions

Who bears the cost of scaffolding and aerial platforms during an unsuccessful search for water ingress?

If the joint expert inspection by water spraying shows that the facade or external window package is not the cause of the damage, the access and testing costs fall on the client or on the responsible trade package once designated. The contractor must make a written reservation before the lifting equipment is deployed, stipulating full re-invoicing of the services if their work is cleared.

Can dye tracers be used when searching for water ingress in a ventilated facade?

The use of fluorescent tracers such as fluorescein is possible but requires great caution. These substances leave lasting marks on porous coverings, exposed concrete soffits and light-coloured rainscreen membranes. Their use is reserved for paths hidden under copings or behind guide rails, after written agreement from site management on the risk of residual staining.

How should one react if the water ingress reappears several days after the targeted spraying has stopped?

This time lag indicates water retention within the thickness of the thermal insulation or along the load-bearing profiles before overflowing onto the slab. The residual moisture should be mapped using a non-destructive capacitance meter and the appearance of water correlated with the actual outdoor weather conditions, thus ruling out a direct link with the recent targeted tests.

Can the client withhold the release of the bank guarantee during the investigation?

During the two-year warranty period under the SIA 118 standard, the client may block the release of the bank security only for an amount proportionate to the estimated cost of the notified defect. As soon as the zone-by-zone investigation rules out the facade contractor's responsibility, the company is entitled to demand the full release of the retention on its account.

Texts and standards cited

  • norme SIA 118General conditions for the execution of construction works, governing acceptance of the work, the two-year warranty period and the handling of notices of defects
  • CO art. 367Examination of the condition of the work after delivery, notification of defects by the client and the right of each party to request an examination by experts

In the same section