Skip to content
Website
🧱 CFC 221Measured performance and building envelope acceptanceChapter 6 of 10 in the section

Acceptance of a facade: viewing distance, lighting and appearance reservations

This chapter gives you the method for framing the visual inspection at acceptance of ventilated facades and external joinery. You will learn to enforce the standardised viewing-distance and lighting conditions, to use the validated reference sample to settle subjective opinions, and to record appearance reservations that are rigorously measured and located.

Key takeaways

  • The visual inspection of cladding is always carried out under diffuse daylight, without low-angle sunlight.
  • The agreed viewing distance neutralises subjective objections raised with one's nose pressed against the wall.
  • The SIA 414 standard defines the permissible flatness tolerances for the framework and the facings.
  • The reference sample signed during the preparatory phase is the only contractual judge of the finished appearance.

Set the visual inspection protocol and the flatness tolerances

Acceptance of a ventilated facing or external joinery often turns into a pointless dispute when the parties examine the work from a few centimetres away or under the low light of the late afternoon. The architectural appearance of a building is never judged with a magnifying glass. To put an end to objections with no technical basis, the works supervisor and the site foreman must impose the viewing protocol from the moment the parties are called to the verification, in accordance with trade practice and the SIA 118 standard.

Reference sample (mock-up)
A reference piece of work or prototype panel produced on site at the start of the works, jointly validated by site management and the contractor, which contractually sets the acceptable level of requirement regarding joints, fixings and surface shades.
  • Required lighting: the inspection is carried out under natural, diffuse daylight, excluding any direct low-angle sunlight or supplementary artificial lighting aimed at the facing.
  • Viewing distance: the standardised stand-back distance for judging the overall appearance of a facade is between three and five metres in French-speaking Switzerland, and at least two metres for checking joinery details.
  • Angle of incidence: the surface must be examined perpendicular to the plane of the facade, without deliberately seeking oblique angles that favour reflections.
  • Observer position: the assessment is made from areas normally accessible to future users (ground level, terraces, pavements), and not from scaffolding pressed against the envelope.

Record, measure and settle appearance reservations in the minutes

During the joint inspection record, the client or the architect points out the imperfections noted. Under art. 367 CO, after delivery, the client examines the condition of the work as soon as it is able to and notifies the contractor of defects. In the case of purely visual appearance defects, acceptance of the work releases the contractor under art. 370 CO for the elements recognisable in a regular examination. The contractor therefore has every interest in recording each remark with absolute rigour.

  1. Orthogonal location on the planIdentify each defect by its facade (North, South, East, West), its level (floor axis) and its structural grid line. Avoid any imprecise designation such as "scratched panel on the entrance side".
  2. Instrument measurementPlace the rule or the 2 m straightedge with feeler shims to quantify the misalignment, the joint spacing or the deflection. Photograph the disputed point including a graduated scale.
  3. Comparison with the reference sampleCompare the visible anomaly with the sample validated at the start of the works. If the colour variation or the microporosity of the coating is present on the signed reference, the finding cannot give rise to an admissible reservation.
  4. Joint drafting of the wordingEnter the quantified result in the minutes: "joint misalignment measured at 1.5 mm on axis C2" rather than a subjective assessment such as "poor finish".
Technical assessment grid for appearance reservations on external facings
Nature of the disputeMeans of inspectionAdmissibility criterion for the reservation
Flatness defect of a composite or metal panel2 m aluminium straightedge and set of standardised shimsDeflection greater than the tolerance defined by the SIA 414 standard
Micro-scratch in the lacquer on a window frameNaked eye at 2 metres without magnifier, diffuse lightingNot visible at 2 m: reservation rejected; visible and marked: local touch-up
Colour shade difference between two cladding boardsVisual comparison at 5 metres with the mock-upDeviation outside the tolerance range of the accepted reference batch
Misalignment at a recessed jointDepth gauge or bevelled ruleExceeds the contractual threshold set in the technical specification

Inspection conditions: agreed distance, natural lighting and rejection of low-angle light

The aesthetic assessment of a ventilated facade cladding or of render on external insulation frequently turns into a dispute when the observer inspects the facings from a few centimetres away. Yet no finishing-work surface withstands an optical check at thread-counting level. To put an end to subjective objections during the completion inspection, the works supervisor and the foreman must recall the contractually set rules of the game: the work is viewed from the public domain or from the circulation areas intended for users, at a minimum viewing distance agreed in writing before the scaffolding is dismantled.

Lighting is the second determining factor in visual assessment. Acceptance is never carried out under directed artificial lighting, nor under low morning or evening sun that disproportionately accentuates the slightest millimetric undulations of sheet metal or reinforcement mesh. The inspection is carried out under diffuse daylight, in clear but slightly overcast weather, perpendicular to the plane of the cladding or at a viewing angle greater than sixty degrees. The extreme cast shadows generated by a point light source can in no case serve as grounds for refusing the work.

Visual inspection parameters by facade component (CFC 221)
Envelope elementMinimum viewing distanceRequired lighting conditionsAdmissibility criterion for the reservation
Finishing render on external insulation (mineral or synthetic renders)3 m from the ground or from pedestrian access routesDiffuse daylight, no low-angle light at allPanel ghosting or repair mark visible from a distance without directed searching
Composite panels or ventilated metal cladding5 m for the whole, 3 m for reveal detailsUniformly hazy sky, no direct sun creating specular reflectionsDent, bulge or joint misalignment exceeding the values of the SIA 414 standard
External joinery frames in powder-coated aluminium or timber-aluminium2 m from the interior floor or the balconyNatural overhead or diffuse lighting, without magnifier or supplementary lightingScratch through the finish coat, chip or colour run perceptible at 2 m
Roller blind slats and aprons of linked-slat blinds3 m perpendicular to the glazingNatural ambient outdoor lightResidual deformation of a slat hindering guidance, or a marked pitch offset

The validated reference sample: arbiter of disputes and method of quantified recording

To put an end to the interminable discussion about the "expected result", producing a reference sample on site beforehand is essential. Installed over a significant surface of two to four square metres, including a corner, a reveal return and a sealing joint, this reference piece must be accepted and formally validated by site management and the client before series production starts. Once signed jointly, it becomes the sole contractual standard against which any variations in texture, gloss or flatness are compared.

  1. Preliminary check of the substrate and of the disputed areaPosition a straight two-metre metal straightedge on the disputed area, without applying pressure, to quantify the deflection using a graduated wedge or a feeler gauge, then compare the measured value with the tolerance of the SIA 414 standard.
  2. Direct comparison with the reference sample surfaceExamine whether the observed variation (grain size of the render, flatness of folded sheet metal, micro-scratch on anodising) exceeds what was validated on the reference sample under the same light exposure.
  3. Technical qualification and traceability in the minutesEnter in the record the precise reference of the panel or bay, the exact value of the measured deviation in millimetres and the functional impact. If the deviation lies within the normative thresholds, record that the work conforms in order to close the discussion definitively.

Where the deviation exceeds the tolerance without compromising watertightness against driving rain or the durability of the system, the dispute amounts to a minor aesthetic price reduction or a targeted local touch-up. The facade contractor keeps control of the construction site by countering purely subjective assessments with a rigorous, quantified and standards-based method.

Handling appearance disputes: technical arbitration and recourse to expert assessment

When site management refuses to lift an appearance reservation at the completion inspection, the facade contractor must immediately neutralise the subjective debate by bringing the parties back to the agreed normative framework. The inspection is never carried out at point-blank range or under supplementary artificial lighting. If the alleged anomaly — micro-undulation of a composite panel, shade variation from the anodising bath or tool mark on facade render — cannot be distinguished at the conventional viewing distance in diffuse light, it does not constitute a defect in the sense of the work. Where the minutes remain deadlocked, the approach requires a rigorous method of on-site arbitration.

  1. Define the perimeter of the disputeRefuse any global entry such as "south facade non-compliant". Require the precise entry of the disputed element: axis reference, floor level, panel number or external joinery grid line. Apply the two-metre straightedge to quantify the geometric deviation under the SIA 414 standard.
  2. Compare the facing with the reference templateMove the reference sample validated before the works to place it in the same plane and under the same natural exposure as the element in question. If the variation in colour, texture or gloss falls within the range accepted by this reference, the work is deemed to comply with the recognised rules of the trade.
  3. Record the disagreement and call on a neutral third partyIf the client refuses to sign the acceptance without an unjustified reduction, each party may request the opinion of a neutral expert in accordance with art. 367 CO. Site management then jointly appoints a trade expert to rule on the usual visual tolerances of the trade.

Frequently asked questions

At exactly what distance should one stand to judge the appearance of ventilated cladding?

The visual inspection is carried out at the normal viewing distance of the building, set by convention at between three and five metres in French-speaking Switzerland, perpendicular to the facing. For upper floors not accessible from the ground, the inspection is carried out from the normal external circulation areas or balconies, without binoculars or scaffolding set close to the wall, in order to assess the work according to its real architectural perception and not through artificial magnification.

Can site management reject render on external insulation under low-angle lighting?

No. The appearance tolerances of external render are judged in diffuse daylight, overcast sky or high sun, without extreme tangential lighting. Low morning or evening light creates microscopic cast shadows inherent in the hand-applied texture of a floated or scraped render. Under the SIA 414 standard, flatness that respects the permissible deflection under the straightedge cannot be rejected because of fleeting shadows.

What should be done if no reference sample was validated before the metal panels were installed?

The absence of a signed sample requires reference to the tolerance ranges of the Swiss professional guidelines for metal construction and powder coating. The visual inspection is then based on standard catalogue elements and on the dimensional deviations of the SIA 414 standard. The parties must accept the micro-variations in colour inherent in industrial anodising or powder-coating baths, visible only at certain very oblique angles of incidence.

How should an appearance reservation be worded in the minutes so that it is legally usable?

A reservation must be located, measured and described objectively. Avoid vague adjectives such as "unacceptable" or "poorly executed". Enter, for example: "cassette panel grid C4, level +2, surface scratch of 15 mm visible at 3 m in diffuse light". This precision makes it possible to assess the real price reduction or to arrange a targeted touch-up without freezing all the contractual advance payments due on completion of the envelope.

Texts and standards cited

  • norme SIA 414Dimensional tolerances in building
  • CO art. art. 367 COExamination of the work and notification of defects; recourse to experts by each party

In the same section