Key takeaways
- The continuous perimeter bead prevents stray air circulation behind the thermal insulation boards.
- The effective contact area of the bonding mortar must reach at least forty per cent.
- Mechanical anchoring takes up the wind suction forces in addition to the chemical adhesion.
- Building edges and corners require a targeted increase in the number of fasteners.
Bonding the boards with a perimeter bead and central dabs
On an external thermal insulation construction site, bonding does not serve only to hold the insulation against the masonry: it blocks any convective air circulation between the board and the supporting wall. SIA 243 sets the execution requirements for external thermal insulation composite systems with render on insulation. The method known as the perimeter bead completed by central dabs is the recognised standard of good practice for expanded polystyrene or mineral wool boards laid on mineral substrates with slight flatness tolerances.
- Chimney effect
- Phenomenon of rising air convection developing in the residual void between the insulation board and the supporting wall. The absence of a closed adhesive bead around the perimeter promotes these air movements, which ruins the overall thermal resistance and accelerates the spread of smoke or flames in the event of fire.
Bonding with isolated dabs only, without a perimeter strip, is strictly prohibited. During application, the tradesman applies, by trowel or machine, a continuous bead of adhesive mortar 50 mm wide and 15 to 20 mm thick along the four edges of the board, set back about 20 mm from the edge to prevent squeeze-out into the joints. In the centre of the board, three to six evenly distributed adhesive dabs provide the necessary material. Once the board is pressed and rubbed against the substrate with a large float, this mortar is compressed to cover at least 40 % of the total surface of the board, the threshold set by SIA 243.
- Applying the closed beadLay an uninterrupted bead of adhesive mortar around the whole perimeter of the board, two centimetres from the outer edge, leaving no break on any of the four sides.
- Arrangement of the inner dabsPlace three to six pats of fresh mortar, about ten centimetres in diameter, symmetrically distributed in the centre of the board.
- Pressing and alignmentPresent the board against the masonry wall, press firmly with a slight back-and-forth movement, then check the flushness with a two-metre straightedge.
- Visual check by samplingRemove one freshly applied board at the start of the shift to measure the actual compression and check that the minimum rate of 40 % is met.
Calculating and setting out the mechanical anchoring according to exposure zones
Although the adhesive mortar takes up the dead weight of the system and part of the adhesion, mechanical fixing with expansion or screw-in anchors is essential to ensure stability under the pull-out forces caused by wind. Under art. 364 CO, the contractor is liable for the proper and faithful execution of the work; it must therefore strictly apply the anchoring plan validated by the system supplier and the engineering office, respecting the effective anchorage depth in the structural work.
Wind loading is not uniform across a whole façade. The most violent suction occurs at the external corners of the building and under roof parapets, where suction vortices form. SIA 243 therefore distinguishes the central area of the façade from the edge zones. In the edge strips, whose width generally corresponds to one tenth of the smallest plan dimension of the building and is not less than one metre, the density of anchors must be significantly increased.
| Façade zone | Building height | Minimum anchor density | Recommended layout |
|---|---|---|---|
| Main field (central area) | Less than 20 metres | 4 to 6 anchors per m² | T-pattern at intersections and in the centre |
| Main field (central area) | More than 20 metres | 6 to 8 anchors per m² | W-pattern with reinforced fixing at the centre |
| Edge zone and external corners | Less than 20 metres | 8 anchors per m² | Closer spacing along the edges |
| Edge zone and external corners | More than 20 metres | 10 to 12 anchors per m² | Tight grid at the edges and heads recessed under washer |
Anchors are installed after the bonding mortar has fully hardened, i.e. at least 24 to 48 hours after the boards are laid. Drilling through the insulation into still-fresh adhesive would break the adhesion bonds that are still setting. Drilling into hollow brick must be done without hammer action so as not to break the internal walls of the masonry, whereas reinforced concrete requires drilling with a standard hammer drill. To protect crews against the risk of tripping or falling linked to tools and materials at the foot of the workstation, OTConst art. 17 requires that measures be taken to ensure safety on the walkways and workstations of the scaffolding.
Mechanical complementarity: load transfer and minimum adhesion
In an external thermal insulation composite system with render (EPS or stone wool), the connection to the mineral substrate does not rely on a random addition of mortar and mechanical fasteners. The two types of connection perform distinct, coordinated physical functions in the face of climatic and gravitational loads. The adhesive mainly takes up the dead weight of the insulation system and the reinforced base coat, while blocking micro-movements of thermal origin. Expansion or screw-in anchors take up the pure tensile forces generated by wind suction, in particular pull-out forces due to suction.
SIA 243 sets the execution requirements for laying bonded or anchored-and-bonded insulation boards. For a standard expanded polystyrene or mineral wool board, the actual contact area of the adhesive mortar after pressing against the masonry or concrete must never fall below the critical threshold of 40 %. If the substrate has poor flatness or excessive roughness, this ratio must be raised to 50 % or even 60 % to ensure overall cohesion. Where a doubtful or powdery substrate is found during preliminary checks, CO para. 3 requires the contractor to inform the client immediately if any circumstance jeopardises the proper or timely execution of the work.
The bonding mortar is applied to the back of the board as a continuous perimeter ribbon about 5 cm wide and 1.5 to 2 cm thick, completed in the centre by three to six adhesive dabs calibrated with a trowel or notched float. This bead must be chamfered or set back slightly by 1 to 2 cm from the board edge during initial application, so that when the board is pressed with the plasterer's straightedge, the adhesive flows to the edge without ever entering the vertical or horizontal joints between boards. Joints soiled with mortar create rigid thermal bridges that promote cracking of the reinforcing mesh.
Anchoring pattern, edge zones and density calculation
Supplementary mechanical anchoring is systematically required whenever the nature of the substrate demands it (aerated concrete, calcium silicate brick, retained old mineral render) or when the weight per unit area of the system exceeds the limits allowed for bonding alone. Mechanical fixing does not replace bonding: it locks the board against dynamic pull-out when the surface tensile strength of the substrate is insufficient or cannot be measured. The anchoring plan must scrupulously respect the geometry of the façades, distinguishing the central main field from the edge zones.
| Façade zone | Building height | Insulation type | Minimum number of anchors |
|---|---|---|---|
| Main field (centre) | 0 to 8 m | Graphite / white EPS | 4 to 6 fixings / m² |
| Main field (centre) | 8 to 22 m | Stone wool (board) | 6 to 8 fixings / m² |
| Edge zone (width e/10) | 0 to 22 m | EPS or mineral wool | 8 to 10 fixings / m² |
| Projecting corners and parapets | > 22 m | All rigid insulation | 10 to 12 fixings / m² |
The edge zone extends over a fixed width calculated from the plan dimension of the building (commonly one tenth of the smallest dimension of the façade, not less than 1 metre and not more than 2 metres). It is on this perimeter strip, as well as around the external corners of the building and under the parapets of flat roofs, that wind vortices create the most violent suction. The anchor density there is increased by 30 % to 50 % compared with the central area to keep the board in close contact with the masonry.
- Waiting for the bonding mortar to dryDo not drill any anchor holes before the adhesive bed has fully hardened, i.e. 24 to 48 hours depending on the temperature and humidity conditions of the construction site. Drilling through fresh mortar detaches the dabs through mechanical vibration.
- Drilling and choice of drilling modeAlways use rotation only, without hammer action, for masonry made of hollow clay bricks or aerated concrete in order to protect the internal walls of the material. The hammer drill is reserved for solid reinforced concrete.
- Setting out according to the geometric patternArrange the anchors using the mixed method: T-anchors (at the intersections of staggered joints) to lock the edges, and anchors in the centre of the board which must pass through the thickness of an adhesive dab to avoid deformation of the insulation when tightened.
- Countersinking and embedding the washerDrive in the anchor plate by screwing or hammering with a countersunk collar below the surface, then close the recess with an insulating disc cut from the same material. This recessing eliminates the point thermal bridge and prevents circular halos from appearing on the final render.
Adhesion non-conformities and anchoring failures: corrective measures
On an external thermal insulation construction site, the execution deviations found when checking the insulation boards mainly concern insufficient compression of the adhesive mortar or poor anchorage of the mechanical fixings. When the minimum bonded area does not reach the threshold required by SIA 243, or if the perimeter bead has breaks that allow air circulation by chimney effect, the façade contractor must react before the hydraulic binder has fully set.
- Immediate removal of the fresh boardIf the mortar is still fresh, detach the non-conforming board, scrape the adhesive off the masonry substrate and reapply a continuous closed perimeter bead with three regular central dabs.
- Pull-off test on set mortarWhen the adhesive mortar has hardened and there is doubt about adhesion, carry out an in situ pull-off test according to the system supplier's guidelines. Record the pull-off values in the site diary.
- Reinforcement by compensatory mechanical anchoringIf the substrate proves friable or if the bonded area is less than 40 %, recalculate the anchoring pattern in consultation with site management and the manufacturer. Adjust the number of anchors per square metre, particularly in the edge strips subject to strong wind suction.
- Formal notice under the Code of ObligationsIn accordance with CO, if any circumstance jeopardises the proper or timely execution of the work, the contractor informs the client. The report must specify the nature of the substrate non-conformity and the recommended bridging technical measures.
Where a mechanical fixing is ineffective, such as an anchor with a plate spinning freely in a hollow clay brick or porous concrete, it is prohibited to leave the plastic body in place without remedial work. The defective anchor must be extracted or pushed into the insulation, the hole filled with a core of the same insulation material, and a new hole drilled at a minimum distance of 150 millimetres with a suitable tool without hammer action.
Frequently asked questions
How should you react if the adhesive mortar does not reach the prescribed 40 % contact area?
If the mortar is still open, remove the affected boards immediately, scrape off the mortar and refit with a continuous perimeter bead and more generous dabs. On dry mortar, notify site management and carry out a compensatory anchoring campaign sized to take up 100 % of the wind loads, in accordance with the system supplier's guidelines and SIA 243.
Why is the closed perimeter bead mandatory in addition to the central dabs?
The perimeter bead prevents any convective air circulation behind the insulation, which preserves the overall thermal performance and eliminates the risk of flame spread in the event of fire. It also blocks the venturi effect under wind suction that would try to pull the board off from behind. The central dabs only stabilise the board against bowing deformation and absorb positive pressure.
What is the rule for positioning anchors in the edge zones of the building?
Corner and edge zones are subject to wind suction stresses clearly higher than the main field. Over an edge width equivalent to one tenth of the width of the building, the anchoring density is generally increased, often from 4 or 6 anchors per square metre in the main field to 8 or 10 fixings per square metre, according to the manufacturer's technical charts validated for the project.
What should you do when an anchor passes through the insulation without finding solid anchorage in the wall?
Never attempt to inject adhesive or resin into the hole to lock the shank. Remove the unusable anchor or cut its collar flush, fill the insulation cavity with a fitted insulating plug, then drill a new anchoring point at least 150 millimetres from the original one. Then check the hammer stroke and the hardness of the substrate before driving in the new anchor plate.
Texts and standards cited
- SIA 243Installation of rendered external thermal insulation systems (boards, bonding, anchoring and tolerances).
- COMaterial and ground: the contractor is responsible for the good quality of the material supplied; if the ground or material supplied is defective, or if any other circumstance jeopardises the timely or proper execution, he informs the client.
