Key takeaways
- A floury or powdery substrate rules out any bonding without through-fixing mechanical fasteners or suitable preparatory treatment.
- The adhesive tape cross-cut test instantly reveals the lack of cohesion of old painted backgrounds.
- Flatness measurement under a two-metre straightedge determines the choice of bonding method.
- Excessive moisture and formwork marks irreparably compromise the chemical setting of the bonding mortar.
Testing the adhesion and mechanical cohesion of walls
On a façade construction site, applying a rendered external insulation system requires a mechanically stable base. Bonding expanded polystyrene or stone wool boards onto a powdery surface, or one covered with a degraded old coating, inevitably leads to failure of the work under wind suction and thermal shear, especially at edges and corners. The façade contractor must check the surface compactness before any bonding. On new clay brick or aerated concrete masonry, sawing dust and mortar runs reduce the wetting of the adhesive. On old masonry or aged concrete, crazing, degraded carbonation and dust form an early slip plane that fails after a few seasons. The cohesion of the substrate determines the durability of the whole façade.
- Tactile examination, scraping and dry brushingRub the wall firmly with the palm of your hand or a dark cloth, then scratch the surface with the tip of a screwdriver, particularly at the joints. If a sandy film comes off or the material crumbles under light pressure, the substrate is powdery. Vigorous brushing, dust removal with compressed air or a solvent-free penetrating primer becomes mandatory before any bonding.
- Cross-cut and tape pull-off testOn substrates that are already rendered or painted, cut a cross-hatch with a cutter of six vertical and six horizontal lines spaced two millimetres apart, down to the mineral substrate. Apply a strong cloth-backed adhesive tape, press it firmly with the edge of a flat tool, then tear it off in one sharp motion at sixty degrees. If flakes of coating come away, the substrate does not have the strength required to carry the insulation.
- Pull-off test on in-situ control patchesMix the specified adhesive mortar and bond three insulation samples of twenty centimetres square in different orientations. After a drying time of seventy-two hours at more than five degrees, pull axially with a pull-off dynamometer or a traction lever. The result is compliant only if the failure is entirely cohesive within the insulation, and not at the contact plane with the wall or within the adhesive.
Checking the flatness, dryness and cleanliness of the substrate
SIA 243 governs the installation of external thermal insulation systems and sets strict limits for the flatness of the substrate. A distorted façade must never be corrected with extra thicknesses of levelling mortar. An excessive layer of adhesive causes fresh boards to slip and induces differential shrinkage that cracks the base coat. The check is carried out with a straight aluminium two-metre straightedge and a short twenty-centimetre straightedge. Localised hollows must be identified before installation starts.
| Deviation under 2 m straightedge | Deviation under 20 cm straightedge | Permitted bonding method | Preparatory measure |
|---|---|---|---|
| Less than 5 mm | Less than 2 mm | Full-surface bonding with notched trowel | Direct installation without rework |
| From 5 to 10 mm | From 2 to 4 mm | Perimeter bead and adhesive dabs | Check of adhesive transfer |
| From 10 to 20 mm | From 4 to 6 mm | Combined bonding and through-fixing with anchors | Dressing of marked hollows |
| More than 20 mm | More than 6 mm | Direct installation prohibited | Complete prior levelling |
The moisture state and cleanliness of the substrate are as decisive as its geometry. Waterlogged masonry prevents the normal suction of the mixing water and compromises the setting of the cement binder. The substrate must be visibly dry, free of frost, moss and salt efflorescence. Salts crystallised on the surface are removed by dry brushing without water, otherwise nitrates are reintroduced into the porosity. To detect formwork oils, splash a few drops of water on the concrete: if it is not absorbed, high-pressure degreasing is required. This washing must be done several days before bonding to ensure complete drying.
Pull-off tests and adhesive tape test on the substrate
A bonded external thermal insulation system is permanently subjected to shear stresses under its own weight and to strong suction under the action of wind gusts. Bonding a rigid board onto a chalking, dusty substrate or one covered with an old, poorly adhering paint concentrates all the mechanical forces on a surface film with no structural strength. With alternating summer heat cycles and winter frosts, cohesive failure of this weakened zone inevitably leads to entire sections of façade detaching within two to three years. Assessing the surface mechanical cohesion before any bonding is the first preventive measure on new masonry as well as on existing renders.
- Preparing the test areaMark out a representative area on the façade. Core the substrate with a 50 mm diamond core bit down to the sound load-bearing base in order to delimit the pull-off specimen.
- Bonding the pull-off discsRemove the dust from the groove and bond rigid metal discs using a two-component epoxy resin, avoiding any adhesive overflow onto the cut edges.
- Applying axial tensionOnce the resin has hardened, connect the dynamometric pull-off device and apply a continuous perpendicular tensile force until clean failure.
- Reading and interpretationRecord the failure load on the gauge and analyse the failure pattern obtained on the back of the disc to identify the weak point of the substrate.
| Failure pattern | Visual appearance | Measured value | Execution measure |
|---|---|---|---|
| Cohesive in the substrate | Concrete or brick torn out under the disc | Greater than 0.25 N/mm² | Direct bonding permissible |
| Adhesive at the interface | Clean detachment of the epoxy adhesive | Less than 0.25 N/mm² | High-pressure cleaning or primer |
| Powdery surface | Floury film stuck to the disc | Less than 0.15 N/mm² | Stripping or through-fixing with mechanical anchors |
| Paint delamination | Paint film detached from the substrate | Variable depending on condition | Complete stripping mandatory |
On painted walls or suspect mineral substrates, the reinforced cloth adhesive tape test gives a quick diagnosis of surface adhesion. The façade contractor applies a high-tack adhesive strip to the clean substrate, presses it down vigorously to expel air bubbles, then tears the tape off in one sharp motion at an angle of 90 degrees. If residues of render, grains of sand or flakes of paint remain stuck to the adhesive, the substrate is unsuitable for direct bonding. On a well-adhering paint in renovation work, a cross-cut with a cutter comprising six horizontal and six vertical incisions spaced 2 mm apart makes it possible to ensure that no flake comes off when the tape is torn away.
Flatness, dryness and cleanliness according to SIA 243
SIA 243 defines the requirements applicable to rendered thermal insulation systems on external walls. The flatness check is carried out with a rigid 2-metre straightedge moved in all directions over the raw substrate. The maximum permitted deviation under the straightedge is 10 mm for bonding with perimeter beads and central dabs, and 3 mm under the 0.20-metre rule for localised steps. When hollows or bumps exceed these values, excess adhesive thickness impairs the uniform pressing of the boards and requires prior mineral levelling.
The dryness of the substrate ensures proper crystallisation of hydraulic bonding mortars and prevents blistering under the boards. On new cast-in-place formed concrete, a drying time of at least four to six weeks is required before bonding, the moisture content by mass having to remain below 3 %. Moisture checking on the construction site is done by sealing a transparent polyethylene sheet taped at its edges for 24 hours: any condensation under the film or darkening of the substrate indicates active evaporation. Bonding of the insulation remains prohibited as long as infiltrations or capillary rise persist in the masonry.
The cleanliness of the substrate eliminates any slip plane between the mortar and the substrate. Formwork oils, cement laitance, salt efflorescence, soot and plant soiling must be removed. On smooth concrete, high-pressure washing with mechanical brushing removes paraffinic release agents. The final substrate must offer a uniform roughness, balanced water absorption and a total absence of sanding dust to allow micromechanical anchoring and crystallisation of the mineral adhesive.
Site decision: corrective measures for a non-compliant substrate
When the pull-off, surface cohesion or flatness checks reveal a substrate unsuitable under SIA 243, application of the external insulation system cannot begin without prior measures. A bonding mortar applied on a powdery or unstable substrate leads to premature interface failure under thermomechanical stresses and wind.
- Treatment of chalking and laitanceDry sandblasting, shot blasting or mechanical stripping with a concrete milling machine removes the degraded layers. High-pressure hot water washing remains possible, but then requires a complete drying time to meet the dryness required before bonding.
- Correction of flatness deviationsIf the out-of-plumb or the hollows exceed the tolerances permitted by SIA 243, the thickness of the adhesive mortar must not be increased beyond the manufacturer's limits. Two options apply: a compatible fibre-reinforced mineral levelling coat or mechanical levelling with differentiated insulation thicknesses.
- Supplementary mechanical fixing and remedial anchorsIf the direct tensile strength on the substrate remains below the requirements despite cleaning, the installation principle must be changed in agreement with the site management. The system changes from pure bonding to a mechanically fixed system with certified anchors taking 100 % of the loads due to wind suction.
In the event of excessive moisture in the structural work, any immediate enclosure behind an expanded polystyrene board creates a major risk of interstitial condensation and rotting of the bonding layers. Art. 365 CO recalls the contractor's responsibility for examining the material and the ground entrusted to them. When the dryness or adhesion conditions are not met, installation work must be postponed until the masonry has been fully dried out.
Frequently asked questions
How should you react immediately to an existing render that sounds hollow over 15 % of the façade?
The detached areas must be completely chipped off with a pneumatic chisel until sound masonry is reached. Residual dust is removed by brushing and industrial vacuuming. According to SIA 243, the cavities are filled with a compatible admixture-modified mineral mortar, respecting a sufficient curing time. If the hollow area exceeds the critical thresholds of the system supplier, complete stripping of the render becomes unavoidable.
Can insulation boards be installed on damp concrete after heavy rain?
No. SIA 243 requires sufficient dryness of the substrate. Water-saturated concrete prevents the correct setting of cement-based adhesives and promotes the formation of soluble salts under the boards. In addition, trapped water cannot escape to the outside if the insulation is vapour-tight, causing rapid deterioration of the render. You must ventilate or wait until the surface moisture content drops.
What should you do if the pull-off test of the metal disc breaks within the body of the material?
A cohesive failure in the substrate indicates inherently fragile masonry or concrete. If the measured tensile value remains above the specifications of the insulation manufacturer, the substrate is acceptable. If, however, failure occurs at too low a stress, bonding alone is no longer sufficient: you must use a bonded-and-anchored system or one fixed on profiles, approved for this type of soft substrate.
What solution should be adopted when out-of-plumb exceeds 20 mm under the 2-metre straightedge?
Attempting to make up such a deviation with thick dabs of adhesive mortar is prohibited: the adhesive sags on drying and creates thermal bridges. The compliant solution is to apply a reinforced levelling render on the masonry before the insulation, or to combine different insulation board thicknesses adjusted to the millimetre, while recalculating the sizing of the façade anchors in the area concerned.
Texts and standards cited
- SIA 243Installation of rendered external thermal insulation systems (substrate, bonding, tolerances)
- CO art. 365Material and ground: examination and duty of care of the contractor
