Key takeaways
- Reserve a continuous clearance below the headbox so that the curtain and the motor can be removed without damaging the facade.
- Identify the common wear parts such as lifting tapes and polyamide guide studs.
- Plan an annual mechanical check and a cleaning of the fabrics or slats with neutral detergent every two years.
- Record the technical data sheets and the intervention frequencies in the project documentation handed over to the client.
Build in removal access and identify wear parts
The most frequent mistake when installing solar shading in a ventilated facade or an insulated reveal is concealing the mechanical components. A blind whose recessed headbox is sealed by the facade render or blocked by a lintel without a removable soffit rules out any later servicing. When the tubular motor fails or a lifting tape breaks, the technician must break the facade finish or give up the intervention. Installation planning requires a continuous free space below the headbox and a front or bottom mechanical access of at least 120 mm to slide in screwdrivers, remove the closing plate and release the fixing brackets of the winding shaft.
- Removable soffit
- Lower cladding element of the blind headbox, clipped or screwed, designed to be removed without heavy tools so as to reach the mechanism directly without damaging the facade render.
| Component | Mechanical role | Observed wear | Removal condition |
|---|---|---|---|
| Lifting tape (Texband) | Lifting and tilting of the slat pack | Fraying, shearing at the eyelets | Full access to the shaft below the headbox |
| Slider studs | Lateral guiding of the slats in the guide rail | Breakage in strong wind or friction wear | Partial removal of the guide rail |
| Tubular motor | Drive of the shaft and limit switches | Mechanical seizure, capacitor failure | Side clearance to extract the shaft |
| Brush seals of the guide rail | Acoustic damping and guiding | Crushing, hardening under ultraviolet | Replacement by sliding out of the groove |
The common wear parts are directly exposed to thermal cycles and the dynamic loads of the wind. Lifting tapes made of synthetic fibres and polyamide sliders deteriorate under ultraviolet radiation and repeated friction against the guides. From the moment the joinery and facade metalwork are ordered, the installer makes sure that the profiled guide rails have fixing screws that can be removed without damaging the added reveals. Once the soffit has been removed, the winding shaft must be able to drop vertically, without forcing against the side cheeks of the headbox or deforming the lacquered cladding sheets.
Setting the service interval and formalising the manual in the project documentation
The durability of a linked-slat blind or a screen fabric depends on strict compliance with a maintenance interval. Without preventive follow-up, abrasive dust jams the gears, microparticles build up in the guide rails and moisture trapped in the headboxes causes irreversible mould. For inspection work at height, art. 3 OTConst provides that work is planned so that the risk of occupational accident, occupational disease or health impairment is as low as possible. This requires future means of access to be documented from the handover phase of the construction site.
- Visual check and dusting every six monthsInspect the alignment of the slats, the surface condition of the fabrics and the fixing of the guide rails. Remove plant residues and dust with a soft brush. Wash with water and neutral detergent, never using a high-pressure washer, which tears the seams and damages the powder coating.
- Annual lubrication and wear checkClean the groove of the guide rails. Spray a dry silicone lubricant onto the friction surfaces to prevent the studs from fouling. Check the condition of the lifting tapes and the regularity of the winding on the winding rollers below the headbox.
- Travel adjustment and mechanical re-tighteningCheck the upper and lower stop limits of the curtain to relieve the curtain at the end of lifting. Check the tightness of the anchor brackets on the structural work to prevent any parasitic vibration under wind pressure.
All maintenance requirements must be carefully recorded in the technical manual included in the project documentation handed over to the client in accordance with standard SIA 118 at delivery. This contractual document brings together the precise inventory of the solar shading installed, the technical data sheets of the fabrics, the references of the motorisations and the detailed schedule of periodic interventions. It also specifies the conditions of safe access for the maintenance teams: position of the anchor rings, permissible ground loads for the lifting platforms and the interior or exterior routes to be preferred. If the owner or building manager receives no formalised instruction on access and service interval, the inevitable lack of maintenance will drastically reduce the service life of the system and lead to premature refurbishment costs.
Intervention methods and clearance of the components below the headbox
The facade contractor and the blind specialist must ensure that every blind headbox or recess remains accessible without damaging the airtightness system or the facade coverings. In French-speaking Swiss practice, access is most often through a removable soffit screwed or clipped in under the lintel. If the soffit is blocked by a peripheral render or by timber cladding without setback clearance, replacing a tubular motor or a shaft bearing requires destructive cutting. The design of the junction between the reveal return and the closing plate must include visible stainless steel screws or a hanging profile allowing removal from the front or from below.
| Type of shading | Required access zone | Specific tools | Parts checked |
|---|---|---|---|
| Linked-slat blind | Recess soffit or hatch under the lintel | Hex key, Torx screwdriver, retaining strap | Lifting tapes (Texband), tilt cords, guide studs |
| Vertical fabric blind (ZIP) | Surface-mounted headbox or profile under the lintel | Electrician's screwdriver, open-ended spanner, glazing suction cup | Technical fabric, PVC guide rails, damping clips, motor |
| Monobloc roller shutter | Interior inspection hatch or exterior soffit | Socket spanner, Phillips screwdriver, stop wedges | Curtain fasteners, automatic locks, bushing bearings |
Physical access to the blind depends directly on the type of opening. Where the window has an accessible tilt-and-turn sash, the blind specialist can work from the interior slab to inspect the tapes and dust the guide rails, provided that the sill height guarantees fall protection. By contrast, for fixed glazing or large sliding bays on upper floors, the intervention requires temporary external means such as a mobile elevating work platform or a ground-supported scaffolding. According to art. 3 OPA, the employer takes the protective provisions and measures that meet the requirements of the ordinance, the other applicable occupational safety provisions and the recognised rules of safety engineering and occupational medicine. The parking position of a platform or the presence of facade anchors must therefore be anticipated from the CFC 221 assembly drawings.
Methodical cleaning, periodic checks and recording in the project documentation
The cleaning of solar shading directly determines its mechanical longevity. Urban atmospheres load the slats and guide rails with abrasive particles that accelerate the shearing of the lifting tapes and cause the polyamide studs to seize. Washing must under no circumstances be carried out with a high-pressure washer: the energy of the jet deforms the thin edges of powder-coated aluminium, tears off the neoprene sealing lips and saturates with water the motor heads protected to IPX4. Cleaning is carried out exclusively with lukewarm clear water with a neutral soap of pH between 6 and 8, using soft sponges or microfibre gloves, followed by rinsing with a gentle jet.
- Visual inspection and dusting of the guide railsBrush the groove of the extruded aluminium guide rails with a soft brush. Remove plant residues and mineral dirt accumulated at the low point, then check the integrity of the rubber damping profile.
- Check of the traction and tilt componentsUnroll the curtain to the lowest position. Examine the textile lifting tapes closely for any sign of fluffing or cuts. Check that the tilt cords are correctly attached to each slat pivot.
- Electrical check and obstacle detectionCommand a complete up-and-down cycle. Make sure the power cuts automatically at the set limit switches and check the sensitivity of the tubular motor when abnormal resistance is met on the bottom rail.
- Technical recording of the operationsEnter the date of the intervention, the designation of the components replaced and the adjustments made on the service sheet intended for the building manager.
These operational requirements and intervention frequencies must be formalised in the operating and maintenance manual handed over on delivery of the works. Included in the project documentation, this manual specifies the minimum service interval — as a rule annual for commercial buildings or every two years for lightly exposed individual housing — and lists the exact wear parts with the original references. This documentation protects the facade contractor: in the event of a dispute over a mechanical blockage or a tape failure, it proves the instructions given to ensure the durability of the installation.
Handling accessibility disputes and maintenance failures
On the construction site in French-speaking Switzerland, the physical inaccessibility of a blind at the first breakdowns is the main source of disputes between the client and the facade contractor. Where the headbox soffits or the reveals have been closed without a removable provision, the impossibility of replacing common wear parts without damaging the lining stems from an interface design error. As soon as the maintenance access planned at installation clashes with uncoordinated added claddings, the foreman immediately records the non-conformity in the site minutes. In accordance with CO, the contractor notifies the client of any circumstance that compromises the proper or timely execution of the work, formalising the obstacle encountered before any attempt at destructive removal.
- Joint inspection record of the obstacle: photographic survey of the facade or metalwork elements blocking the clearance of the curtain or the motor.
- Refusal of damaging interventions without a written order: written confirmation required from the site management before any cutting of exterior cladding or sill.
- Formal notice on safety conditions: notification if the heights or overhangs require a platform not provided for in the contract to reach the work, in accordance with the ordinance on construction work.
In the event of a loss linked to a mechanical failure or a jammed guide rail, the manual handed over in the project documentation is the decisive contractual document. If the end client neglects the prescribed maintenance interval — in particular the greasing of the bearings, the visual check of the lifting tapes and the annual cleaning of abrasive deposits — the contractor is relieved of technical responsibility. The maintenance sheets must define precisely the intervention frequency and list the components subject to mechanical fatigue. Where acceptance is refused for an alleged malfunction, CO governs the verification of the work; the installer demands a joint examination by demonstrating the correct initial adjustment of the limit switches and the conformity of the profiles within the tolerances of standard SIA 118.
Frequently asked questions
What should be done if a blind headbox is made completely inaccessible by external insulation?
The installer must immediately refuse to intervene by force. He sends a written notice to the site management, referring to the original execution drawings. Drilling or cutting the insulation requires a formal change order from the client, excluding the blind specialist's responsibility for the subsequent reinstatement of the water and air tightness of the ventilated or rendered facade.
How can the chargeable replacement of lifting tapes during the warranty period be justified?
Lifting tapes and cords are among the common wear parts subject to continuous abrasion. If the manual handed over in the project documentation specifies a six-monthly fouling check and the client has neglected this maintenance, premature wear from friction of sand or foreign bodies is not a product defect. The repair service must therefore be invoiced as maintenance.
What solution should be adopted if access requires unforeseen lifting equipment during operation?
During planning, the maintenance access provided must mention the intervention constraints. If a later change to the ground or a glazed canopy prevents the deployment of a sliding ladder or a mobile scaffolding compliant with the ordinance on construction work, the extra cost of mobilising a truck-mounted platform falls exclusively on the owner of the work, for lack of a reserved passage.
What maintenance interval should be recorded for external blinds installed in an urban environment?
In an urban or industrial environment, the technical manual requires an annual maintenance interval for the complete cleaning of fabrics, guide rails and slats in order to remove acid particles. A twice-yearly check of the fixings, the tightness of the articulated arms and the play of the guide studs ensures operational safety against gusts and prevents untimely jamming of the motorised mechanisms.
Texts and standards cited
- COmaterial and ground: the contractor is responsible for the good quality of the material he supplies; if the material supplied by the client or the ground designated by him is found to be defective, or if another circumstance compromises the proper or timely execution of the work, he must inform the client immediately, failing which he bears the consequences (para. 3)
- COafter delivery, the client checks the condition of the work as soon as he can and notifies the contractor of defects; for an immovable work, he has 60 days to notify them and a shorter contractual period is void (para. 1bis, in force since 1 January 2026); each party may request an examination by experts (para. 2)
- norme SIA 118General conditions for the execution of construction work
- OTConstOrdinance on the safety and health protection of workers in construction work
