Skip to content
Website
🧱 CFC 224Penetrations, dormers and special detailsChapter 8 of 10 in the section

Roof against a party wall: upstand, wall coping and access for maintenance

This chapter details the roofing-sheet-metal rules for connecting a pitched roof against a party masonry wall. You will learn how to size upstand heights according to exposure, how to profile a wall coping that ensures water run-off without damaging the adjoining property, and how to secure the formal authorisations from the neighbouring owner before starting work on the construction site.

Key takeaways

  • The formal agreement of the neighbour sharing the party wall is an absolute condition for any physical work on the top of their wall.
  • The vertical metal upstand rises at least one hundred and fifty millimetres above the tile.
  • The overlap strip protects the mechanical chase against infiltration and facade run-off.
  • Permanent anchorage devices must be provided to ensure future maintenance without heavy scaffolding.

Agreement with the neighbour and sizing of the metal upstand

Connecting a pitched roof slope against a party wall exposes the tradesperson to a dual constraint, both technical and legal. When the adjoining building rises above the verge or when the wall separates two properties built at unequal heights, the slightest intervention affects the neighbour's structure. Before setting out the first batten or cutting any chase into the masonry, the formal agreement of the adjoining owner must be obtained in writing. This agreement must specify the right to support the sheet-metal work, temporary access to their plot for the fitters, and responsibility in the event of prior damage to dilapidated render. Without this signed document, the roofing sheet-metal worker faces an immediate stoppage of the construction site, with the obligation to remove metal elements fixed without legal title on another person's land.

In terms of construction, the underlay must be taken up against the wall even before the roofing battens are fitted. This flexible waterproofing flashing is bonded to the mineral substrate with a suitable sealant, then held by a clamping batten. The upstand height of the formed metal, whether titanium-zinc, copper or thermo-lacquered aluminium of zero point eight millimetre, depends on the slope of the pitch and the snow zone. Swiss professional practice prescribes a minimum clearance of one hundred and fifty millimetres above the finished level of the roof covering. At altitude or on slopes strongly exposed to prevailing winds driving rain, this upstand is increased to two hundred millimetres to prevent capillary back-flow behind the sheet.

Minimum upstand heights by roof configuration
Junction situationPitch slopeMinimum upstand heightMethod of fixing to the wall
Low wind exposureSlope greater than 25 degrees150 mmChased flashing strip or plugged-and-bonded
High exposure or sunken valleySlope of 15 to 25 degrees200 mmDouble fold with metal counter-flashing
Alpine zone or snow accumulationAny slope250 mmDeep chase with lead flashing

Water is drained along the party verge line either by individual side flashings interleaved under each course of plain tiles or slates, or by a sunken valley with continuous discharge for pantiles or large-format tiles. This valley must have a U-shaped profile with a hemmed edge on the tile side to prevent any lateral overflow during a heavy storm.

Wall coping and organisation of long-term maintenance

When the party wall stops at a low height above the roof plane, the durable solution is to fit a metal wall coping that fully caps the masonry edge. This coping prevents rainwater from entering through the top of the wall, a critical point of deterioration during freeze-thaw cycles. The developed width of the sheet must include a minimum cross-fall of two per cent directed towards the inside of the roof concerned, so as not to discharge run-off water onto the facade or land of the neighbour. This detail protects the neighbourhood from oxidation staining and meets the obligation to discharge one's own water onto one's own plot.

  1. Preparing the substrateClean the edge of the party wall with a flat chisel, apply a levelling screed with a cross-fall directed towards the receiving pitch, then lay an anti-corrosion separating felt.
  2. Fitting the anchor bracketsMechanically fix galvanised or stainless steel angle brackets spaced at fifty centimetres, taking care not to split the coping bricks.
  3. Seaming the sheet-metal elementsInterlock the formed lengths of wall coping with projecting drip edges of thirty millimetres, joined by double flat-lock seaming or expansion sliders to absorb thermal movement.
  4. Connection to the vertical upstandCover the roof-covering upstand with the downward leg of the coping, ensuring a watertight overlap of sixty millimetres without rigid bonding that would block expansion.

Once the work is finished, the space between the pitched roof and the party facade often becomes an inaccessible point, wedged between two private properties. Planning maintenance from the design stage is essential. In accordance with art. 82 LAA, the employer must take all measures for the prevention of occupational accidents and diseases that experience has shown to be necessary, that the state of the art makes applicable and that are appropriate to the given conditions. With this in mind, installing safety hooks for a pitched roof or a permanent lifeline allows roofing sheet-metal workers to inspect the sunken valley later without having to set up scaffolding again on the neighbouring land.

Periodic maintenance includes clearing dead leaves accumulated in the side flashings and checking the elasticity of the sealing beads at the top of the flashing. A clear maintenance plan handed to the client, together with the negotiated access authorisations, keeps the structure sound for several decades.

Agreement with the neighbour and ladder-access protocol

Carrying out a sheet-metal junction against a party or private wall built on the property boundary immediately confronts the team leader with a legal constraint: the physical impossibility of building the work without overflying or setting foot on the adjoining land. When neighbouring buildings have asymmetrical ridge heights or enclosed mansard break lines, technical access can no longer be ensured once the new roof covering is finished. If a circumstance compromises the proper or timely execution of the work, the contractor informs the client, in accordance with the duty to notify laid down in art. 365 CO.

  1. Joint condition surveyDraw up a complete photographic record of the top of the wall, the render, the party roof coverings and the existing sheet-metal work in the presence of the neighbour or their representative before any structure is erected.
  2. Signing the ladder-access agreementHave a three-party agreement (client, neighbour, company) initialled, defining the dates of work, the support areas on the ground or on the roof, and the type of fixings permitted in the body of the wall.
  3. Planning maintenance without returning to third-party landRecord in the as-built file the arrangements for inspecting the party gutter or side flashing from the main roof, thus avoiding the need to demand a permanent access easement from the neighbour.

The formalised agreement must state the size of the eaves overhang and the footprint of the wall coping. Water run-off that discharges rainfall onto the adjoining property without an easement entered in the land register directly engages the liability of the owner of the renovated building and calls into question the compliance of the roofing work.

Executing the watertight upstand, wall coping water run-off and inspection points

Connecting against a rough or rendered party facade requires a minimum upstand height of 150 mm along the line of steepest slope. This dimension must be measured vertically from the top of the tile or slate to the upper overlap fold of the flashing strip. At altitudes above 800 metres or on a slope exposed to prevailing winds carrying powder snow, the metal upstand must be increased to 200 mm, or even 250 mm, to prevent back-flow by capillarity and melting under the roofing elements.

Installation requirements for the metal components of the party joint
Building elementMaterial and developed widthJointing techniqueWater run-off detail
Top wall copingTitanium-zinc or copper 0.80 mmContinuous flat brackets, single seamDrip edge set at least 20 mm clear of the wall
Foam-backed flashing stripThermo-lacquered aluminium or zincMechanical fixing with hammer-in plugsRun-off fold inclined at 45° on elastomer sealant
Sealing side flashingsHalf-hard copper or zinc 0.70 mmInterlocked under each course of roof coveringSafety side fold turned down over 15 mm
Recessed verge valleyFolded sheet with slidersWatertight sliding seam jointsDischarge to eaves with wind-break clip

The wall coping enclosing the party masonry top must absolutely have a minimum cross-fall of 2 to 3 % directed towards the drained roof pitch, preventing any seepage onto the party facade. The hem or lower drip edge forms a clean water drop, at least 20 mm from the face of the rendered wall, avoiding run-off marks and the detachment of render by frost.

For later maintenance work on steeply pitched slopes, the construction work ordinance specifies in particular at OTConst the measures to be taken at roof edges to prevent falls from a fall height of more than 2 m, with work carried out only from scaffolding or a mobile elevating work platform once the slope exceeds 60°. The technical provisions made when forming the party junction therefore directly determine the safety and feasibility of future maintenance operations.

Party wall deadlocks, hidden leaks and remedies

When the construction site meets the sudden refusal of the neighbouring owner to allow access to their land or to let the wall coping be fixed to the top of the party wall, the sheet-metal team must suspend anchoring operations at the boundary. The contractor applies art. 365 CO: if a circumstance compromises the proper or timely execution of the work, they must inform the client immediately, failing which they bear the consequences. The roofing sheet-metal worker forces no passage and installs no overhanging water run-off fold without legal title. The works supervisor records the obstruction in the site diary, notifies a partial technical stoppage to the site management and asks the client to arbitrate in order to formalise the easement or assert the cantonal ladder-access right.

If a leak occurs after handover on a junction bordered by a higher party wall, the diagnosis requires action without delay to stop the rotting of the verge rafters and the wetting of the thermal insulation. The lack of access from the neighbouring land complicates leak detection. The company must then use non-destructive investigation techniques: video inspection by endoscope under the boarding, fluorescein tracing under the chase clips or depressurisation of the sealed area. If the defect comes from an insufficient upstand hidden by a detached flashing, the repair requires dismantling the roof-covering verge from the inner slope to rebuild a zinc or copper flashing that complies with the technical rules.

  • Formally record the defects with a joint photographic survey before any partial dismantling of the sheet-metal work at the boundary.
  • Temporarily secure the leaking area with a ballasted reinforced tarpaulin, fixed only on the slope belonging to the client.
  • Require the site management to summon the neighbour to draw up an emergency intervention protocol ensuring safe access.

Frequently asked questions

What minimum upstand height must be observed against a party wall without eaves?

Swiss technical practice prescribes a minimum vertical upstand of 150 mm above the drainage plane of the finished roof covering. In regions with heavy snowfall or in situations very exposed to wind, this dimension must be increased to 200 mm or more, to prevent capillary rise and melting of snowdrifts. The metal upstand must absolutely be protected by a mechanically fixed chase profile or covered by a wall coping that sheds water.

Can a wall coping be anchored directly to the masonry of the neighbouring building?

Any work on the neighbour's wall requires their formal written authorisation before the construction site opens. Even if the wall is a party wall under civil law, drilling for plugs, chasing with an angle grinder or fitting seaming brackets modifies the party structure. Without a prior agreement governing the party wall and any easements, these fixings constitute a violation of property that may force the client to dismantle the sheet-metal work at their own expense.

How should maintenance be organised for a sunken party gutter that has become inaccessible?

The initial design must include fixed anchor points for safety harnesses or a permanent lifeline accessible from the roof. If passage over the adjoining land is refused, the roofing sheet-metal worker must provide removable metal parts or leaf guards that can be pulled out from the slope belonging to the building. An annual maintenance contract makes it possible to record regular visits, clean the outlets and check the condition of the expansion clips.

What should be done if the neighbour's existing chase profile lets water into our roof?

The contractor must never modify or seal a defective party profile without a prior joint survey drawn up by the site management. They report in writing to the client any leaks coming from the adjoining property in order to clear their contractual liability. If the neighbour refuses to renovate their flashing, the roofing sheet-metal worker adapts the work by fitting an independent counter-flashing under the existing profile, ensuring continuity of watertightness towards the gutter without altering the third party's structure.

Texts and standards cited

  • CO art. 365material and land: the contractor is responsible for the good quality of the material they supply; if the material supplied by the client or the land designated by them is found to be defective, or if another circumstance compromises the proper or timely execution of the work, they must inform the client immediately, failing which they bear the consequences (para. 3)

In the same section