Key takeaways
- Being connected to an anchor point does not protect you if the fall clearance remains insufficient.
- Art. 29 OTConst governs the use of personal fall protection equipment.
- The sag of the cable under tension is added to the full deployment of the energy absorber.
- The pendulum effect at the roof edge turns an arrested fall into a violent impact against the façade.
Calculate the actual fall clearance below the slope before any engagement on the cable
On a pitched roof, the illusion of safety created by wearing a harness and being connected to a lifeline leads to serious accidents. Personal fall protection equipment does not prevent a fall: it arrests a moving mass. If the trajectory of this mass meets the eaves, an intermediate balcony, a canopy or the ground before the end of the braking distance, the system fails completely. Every fall arrest system requires a minimum free height below the worker, technically referred to as the available fall clearance.
- Fall clearance
- Minimum free vertical distance measured between the starting point of the potential fall (or the working plane) and the first obstacle or the ground, required to allow a worker to be stopped without impact.
The required fall clearance is not limited to the length of a lanyard at rest. It is calculated according to an incompressible kinematic chain that adds up several physical components when equilibrium is lost:
- The initial length of the connecting sub-assembly (lanyard with connectors, or the cable length leaving the self-retracting lifeline).
- The opening travel of the tear-web energy absorber, essential to limit the force transmitted to the body to a tolerable threshold.
- The dynamic sag of the horizontal lifeline, caused by the elastic and plastic deformation of the steel cable and its end absorbers under the shock load.
- The slippage of the worker and the structural elongation of the harness (upward displacement of the dorsal ring under tension).
- The height of the worker, taken as a fixed value from the dorsal ring down to the feet.
- The minimum ground safety margin of 1 metre below the worker's feet after coming to a stop.
| Kinematic component | Typical design value | Influence on the result |
|---|---|---|
| Lanyard with connectors | 1.50 m to 2.00 m | Sets the initial free fall height before activation |
| Energy absorber travel | 0.70 m to 1.20 m | Depends directly on the worker's mass and the fall factor |
| Dynamic cable sag | 0.80 m to 1.80 m | Varies with the span between posts and the residual cable tension |
| Harness deformation and worker height | 1.80 m to 2.00 m | Physical distance between the stretched dorsal ring and the soles of the feet |
| Free safety margin | 1.00 m | Essential guarantee to avoid final bottoming out |
Justify the strength of the anchorages and neutralise the pendulum effect at the roof edge
The use of a lifeline or single anchor points is a subsidiary solution. In accordance with art. 29 OTConst, where it is technically impossible or too dangerous to erect a perimeter guardrail, a façade scaffolding or a safety net, equivalent protective measures must be taken and set down in writing with the involvement of an occupational safety specialist. This requirement demands flawless traceability: an anchor point hastily fixed to an edge rafter without a calculation note or fixing check makes the company fully liable.
The anchorage must withstand not only the static force but also the dynamic impact transmitted to the primary roof frame. On a timber roof structure, the fixing passes through the load-bearing structure: the main purlins or the principal rafters. Counter-battens, boarding or roofing battens are in no case acceptable supports. Mechanical or chemical anchors in a top concrete slab must be documented in an installation record stating the tightening torque and the effective anchorage depth.
Implementation hierarchy and technical justification on a pitched slope
Using a lifeline or a single anchor point on a roof slope is never a default solution. Art. 41 OTConst sets the appropriate measures to prevent falls from a fall height of more than 2 m at roof edges. Installing collective protection remains the absolute priority in site planning. Where the geometry or the nature of the work requires the use of a personal fall arrest system, this choice is a strict technical exception.
According to art. 29 OTConst, where it is technically impossible or too dangerous to erect the usual collective protection, equivalent protective measures must be taken and set down in writing with the involvement of an occupational safety specialist. The cable or rail fall arrest system must be covered by a complete technical file proving that the forces transmitted to the rafters or purlins remain within the admissible limits of the load-bearing structure.
| Slope configuration | Prescribed fall arrest device | Maximum force on the anchorage | Associated critical risk |
|---|---|---|---|
| Pitch below 30°, axial ridge line | Mobile fall arrester on a rigid anchor line or tensioned cable | 6 kN on the structure after absorption | Underestimating the cable sag, which increases the fall clearance needed |
| Pitch from 30° to 60°, work at the edge or valley | Adjustable work-positioning lanyard combined with an energy absorber | 6 kN at the end fixed point | Pendulum effect with a trajectory striking the gable |
| Pitch above 60°, dormer refurbishment | Working platform or dedicated service scaffolding only | Not applicable (fall arrest alone prohibited for this workstation) | Impossible to restrain the worker without a violent impact |
Check before work and management of suspension trauma
Calculating the available fall clearance below the eaves ensures that the roofer will not hit the ground in the event of a slip. However, arresting the fall does not end the emergency response. From the moment the worker is left in mid-air, hanging in the fall arrest harness, the pressure of the leg straps blocks venous return in the lower limbs. Even without prior loss of consciousness, suspension trauma becomes life-threatening within about fifteen minutes.
- Visual check of the identification plate of the anchor point or lifeline: presence of the date of the last periodic inspection and of the maximum number of operators permitted at the same time.
- Check of the condition of the stainless steel cable or guide strap: no broken strands, no contact corrosion under the anchor clamps and no deformation of the tensioner.
- Functional test of the self-retracting fall arrester or the sliding runner: immediate locking under a sharp pull and complete retraction of the cable without seizing.
- Immediate availability of a trauma strap attached to the harness of each roofer, allowing the feet to be braced to relieve pressure on the thighs while waiting for the rescue services.
- Prior definition of the dedicated rescue kit: telescopic pole, speed-controlled evacuation descender and an independent anchor point located above the work area.
Site organisation requires rigorous coordination between the foreman and the installation crew before anyone goes onto the slope. Setting up a personal fall arrest system necessarily requires two workers formally trained in handling the evacuation equipment: a worker alone on a roof fitted with a lifeline is extremely vulnerable in the event of a fall.
Emergency and rescue procedure: what to do after an arrested fall
On a pitched roof, a fall arrested by a lifeline creates a critical situation. Although the worker is held, suspension in the harness compresses the femoral veins and becomes life-threatening within minutes. Moreover, if the available fall clearance at the bottom of the slope or at the roof edge was wrongly assessed, the residual impact against a roof overhang or the ground requires medical evacuation. The team on site must react methodically, without improvisation.
- Alert and maintaining contactAlert the professional rescue services, stating the exact location and the nature of the pitched slope. Keep up continuous voice contact with the suspended worker and ask them to move their legs or to load standby straps in order to limit the venous tourniquet effect.
- Deploying the rescue kitUse the dedicated evacuation device, attached to an anchor point independent of the lifeline that took the load. Lower the rescuer, or hoist the casualty from above with a pulley system, to relieve the tension on the lanyard and the energy absorber without exposing other persons at the edge of the drop.
- Securing and medical checkOnce brought back onto a stable surface or to the ground, place the injured person in a sitting or semi-sitting position, never lying flat, to avoid the shock of blood returning to the heart. Any equipment stressed during the fall is withdrawn from service.
According to art. 29 OTConst, where the erection of a guardrail or scaffolding is technically impossible or too dangerous, equivalent protective measures must be taken and set down in writing with the involvement of an occupational safety specialist. This written framework must include the rescue concept. Art. 41 OTConst sets the appropriate measures to prevent falls at roof edges from a height of more than 2 m. A restraint or arrest anchorage does not replace a rigorous analysis of the void below the eaves.
Frequently asked questions
What should be done if the fall clearance measured at the eaves is less than the total elongation of the fall arrest system?
If the free distance below the roof slope is not enough to absorb the cable sag, the opening of the absorber and the worker's height, a conventional fall arrest system is dangerous. The tradesperson must then switch to a restraint system. By setting a fixed-length lanyard that physically prevents the roofer from reaching the roof edge or the gutter, the risk of falling into the void is eliminated at source.
How can the risk of the pendulum effect be neutralised during sheet-metal work at the roof edge?
When a sheet-metal worker works offset from the central anchorage, a fall causes a swinging movement that can throw them against the façade or make them hit the ground. To eliminate this swing, an intermediate corner anchorage should be added, or fixed deflection points should be installed along the roof edge. Using a lifeline parallel to the gutter also keeps the sliding runner constantly directly above the worker.
Who is authorised to size the structural anchor points on an existing roof frame?
The strength of an anchorage cannot be assumed from a simple visual inspection of the rafters. The mechanical justification must be validated by a civil engineer or by the manufacturer of the anchoring system, depending on the type of timber and the fixings. The installing company issues a fixing record attesting the tightening torques and the compatibility of the anchors or coach screws. Without this proof recorded in the maintenance file, the lifeline may not be used.
Why must a roofer's semi-static rope never be tied directly onto a wall plate purlin?
A raw piece of roof framing has sharp edges capable of cutting a rope or a strap under the dynamic impact of a fall. In addition, the wall plate purlin is often subject to transverse loads for which it was not designed. A temporary or permanent anchorage requires a compliant metal interface, certified to take multidirectional forces, fixed according to the manufacturer's technical specifications and completed with a textile protective sleeve against abrasive friction.
Texts and standards cited
- OTConst art. 29other fall protection: where it is technically impossible or too dangerous to erect a perimeter guardrail, a façade scaffolding or a safety net or catch scaffolding, equivalent protective measures must be taken and set down in writing with the involvement of an occupational safety specialist.
- OTConst art. 41measures to be taken at roof edges: appropriate measures to prevent falls from a fall height of more than 2 m (sheet-metal worker's platform and/or perimeter guardrail depending on the roof pitch); on roofs with a pitch of more than 60°, work only from a scaffolding or a mobile elevating work platform.
