Skip to content
Website
🧱 CFC 224Sarking, ventilation and underlay membraneChapter 7 of 10 in the section

Unheated lofts: insulating the floor and ventilating the space above

Insulating the floor of an unheated loft moves the thermal boundary below the roof structure. This chapter details the continuous ventilation of the cold void above, the strict airtightness of access hatches, the construction of a raised technical walkway and the control of settlement specific to blown insulation, in accordance with Swiss good practice.

Key takeaways

  • Ventilating the cold void generously prevents any condensation under the underlays and battens.
  • The inspection hatch requires an airtight frame and continuous thermal insulation.
  • The raised technical walkway preserves the insulation thickness and protects workers from falls.
  • Blowing requires a calculated extra thickness to compensate for the foreseeable settlement of the wool.

Ventilation of the cold roof void and thermal barrier at floor level

As soon as the thermal insulation is installed on the upper floor of the last heated storey, the entire volume of the unheated loft becomes a cold roof void. This configuration completely changes the physics of the roof: the space under the roof structure no longer benefits from the building's heat losses to dry the air. If water vapour passes through the slab or the ceiling, it meets the cold roof structure and the underlay directly. To prevent mould on the rafters and rotting of the sarking boards, the free volume must be continuously swept by a through-flow of outside air, ensuring the immediate removal of any residual moisture.

The sheet-metal worker and the roofer make sure that the air inlets at the eaves are never blocked by the insulation. At the eaves, fitting a baffle or rigid material stops guarantees a clear air passage between the wall plate and the underlay. Outside air enters through the eaves ventilation slots fitted with rodent-proof grilles, flows over the insulation blanket and escapes through ventilation tiles distributed over the roof slopes or through screened openings in the gable walls. This continuous circulation also prevents summer overheating under the roof covering, preserving the durability of the synthetic membranes.

Ventilation components for an unheated loft void
Ventilation elementLocationTechnical role
Screened eaves slotsFascias and eaves soffitsContinuous fresh outside air inlet
Rigid low-eaves baffleBetween each rafter on the wall plateMaintaining the air section in front of the insulation
Ventilation tiles or gable grillesUpper third of the slopes or wallsRemoval of humid, warm air

Access openings, technical walkway and expansion of insulation materials

The most sensitive point of the work is the loft access hatch. A leaky hatch acts as a thermal chimney through which warm, moisture-laden air infiltrates massively, creating a risk of immediate liquid condensation on contact with the cold environment. The connection between the hatch frame and the dust barrier or vapour barrier of the floor must be bonded with suitable sleeves. The moving panel receives a compressible peripheral airtight seal and a rigid insulation panel with a thermal value equal to that of the floor. A raised frame, forming a rigid kerb, prevents loose-fill insulation from tipping into the opening when the hatch is opened.

To maintain the roof structure, the sheet-metalwork or the chimney stacks, a continuous walkway is essential. Any crushing of the insulation by foot traffic irreversibly destroys its thermal resistance. A raised inspection walkway is installed, made of battens or spacers fixed perpendicular to the joists, topped with a deck of OSB panels or close-butted boards. The underside of this walkway must leave a clear gap of at least 20 mm above the finished level of the insulation to avoid any vapour choke point.

  1. Placing the depth gaugesFix graduated rules on the floor every 25 m² to mark the installation height and the settlement allowance.
  2. Marking out services and boxesRaise and mark electrical conduits, junction boxes and technical elements above the planned finished level.
  3. Blowing with settlement allowanceBlow the mineral wool or cellulose, increasing the thickness by 15 to 20 % according to the settlement class declared by the manufacturer.
  4. Levelling and visual checkCheck the flatness of the insulation bed, particularly around the inspection walkway and around the airtight hatch.

When blowing loose-fill insulation pneumatically, settlement is a major physical factor. Under its own weight and the hygrothermal movements of the ventilated void, the blanket sinks during the first months of use. The initial blown thickness must absolutely include the expansion value specified on the product data sheet, in order to guarantee, in the long term, the thermal resistance required by the standards in force without leaving thermal bridges at the wall plate junctions.

Managing the airflow and protecting the insulation blanket at the eaves

Moving the thermal boundary to the floor turns the volume under the roof into a ventilated unheated loft. The outside air must sweep freely through the void without creating mechanical scouring at the surface of the insulation. The verge and eaves detail therefore determines the thermal durability of the work. The air inlets at the bottom of the slope and the outlets at the ridge or through ventilation tiles must guarantee a continuous draught while preventing direct blast onto the fluffy material.

Airflow management according to the type of floor insulation
Type of material on the floorRisk linked to airflowDevice required at the eavesRidge / loft measure
Blown cellulose fibreScouring and displacement of material near the air inletsRigid inclined baffle at the wall plate, raised 10 cm above the finished bedHigh-level ventilation through staggered ventilation tiles or ventilated ridge without sudden depression
Blown mineral wool (glass/rock)Surface disintegration and uneven settlementRigid water-vapour-permeable board fixed between rafters blocking direct airflowVentilation openings distributed on each roof slope
Rigid boards or cross-laid rollsThermal bypass through cold air infiltration under the jointsWind-tight stop at the joist ends sealed with adhesive sealantLinear airflow preserving the free space above the blanket

Fitting a baffle at the wall plate prevents the expansion of the blown insulation from blocking the air passage. This eaves component, made of rigid underlay board or chipboard, channels the incoming flow directly into the free volume of the loft. The roofer makes sure that this baffle maintains the necessary air gap and prevents direct contact between the fibrous blanket and the flexible roof underlay, which eliminates any risk of moisture being drawn up by capillarity in the event of accidental infiltration under the tiles.

Airtight access structures and allowing for insulation settlement

The access opening must receive a box forming a raised kerb with a height greater than the final thickness of the expanded insulation. This airtight box prevents loose fill from spilling into the opening when the hatch is opened. The hatch lid has bonded insulation of a thermal resistance equivalent to the floor and a peripheral seal compressed when closed. Art. 25 OTConst also requires that openings in floors presenting a risk of falling be secured by a guardrail or a break-resistant, securely fixed cover.

  1. Building the hatch edge boxAssemble an upstand of rigid boards 19 mm thick, firmly fixed to the trimmer, projecting at least 50 mm above the planned finished level of the insulation to contain the blown loose fill.
  2. Installing the raised inspection walkwayFix transverse battens onto the joists to create a continuous walkway linking the hatch to the technical roof elements, at a level higher than the insulation material.
  3. Marking thicknesses and calculating settlementStaple graduated gauges onto the roof structure, calculating the installation thickness increased according to the manufacturer's certified settlement class (foreseeable settlement allowance of 10 % to 20 %).
  4. Visual check and contact airtightnessCheck the compression of the airtight seal around the hatch frame and make sure there is no air bridge between the heated volume and the ventilated space.

The walkway laid on the battens allows future work on sheet-metal stacks, ventilation ducts or the roof underlay without ever walking on or compressing the insulation. Localised crushing destroys the air trapped in the mineral fibres or the cellulose, creating a permanent thermal fault. Art. 17 OTConst requires that measures be taken so that workers are not endangered by falling materials at workstations and walkways, which means firmly stabilising the inspection decks above the insulation bed.

Handling defects and refurbishing ventilated unheated lofts

On pitched roofs, moving the thermal insulation plane from the rafters to the floor completely changes the physics of the loft. When defects occur, they almost always show up as one of three pathologies: massive condensation under the roof underlay through migration of warm, humid air; a thermal bridge combined with mould around the access opening; or wind scouring that moves the blown insulation from the wall plate towards the inside of the loft.

If moisture beads under the roof underlay in cold weather, the primary cause is a lack of airtightness of the hatch or of duct penetrations. According to art. 365 CO, the contractor notifies the client of any circumstance endangering the work. The peripheral seal of the frame, the mechanical tightening of the leaf and the continuity of the membrane at floor level should be checked. The blowing of insulation must never begin without a prior infiltrometry test of the inspection frame or a meticulous visual check of the sleeves.

  1. Correcting air scouring at the eavesInstall rigid baffles fixed between rafters above the wall plate. This baffle prevents the blanket from being eroded while preserving the ventilation air gap coming from the gutter.
  2. Readjusting the hatch and its airtight sealCheck the compression of the tubular elastomer seal on the frame and the adjustable hinges. Replace the toggle catches if they do not guarantee uniform compression of the seal.
  3. Compensating for settlement of the blown insulationMeasure the remaining height after a few months. Top up the layer according to the settlement allowance given in the data sheet to restore the target R value.
  4. Reworking the walkwaysRaise the battens on edge if the decks crush the insulation. Art. 25 OTConst requires openings presenting a risk of falling to be secured; the walkway must remain stable and marked out.

Frequently asked questions

How do you compensate for the settlement of blown mineral wool or cellulose on the floor?

When blowing mechanically, always apply an extra thickness of 15 % to 20 % over the final required useful thickness. Install graduated measuring gauges fixed to the joists every five metres. Record the applied density on the construction site sheet. After six months of natural settlement, check the visual marks; if the height is below the thermal target mark, blow an additional levelling pass.

Why does the inspection hatch often condense after the loft has been insulated?

The hatch is the direct boundary between the warm living space and the cold ventilated void. If its panel does not have an equivalent thermal resistance and a perfectly compressed airtight seal, warm air escapes through thermal draught. The vapour condenses instantly on contact with the cold faces of the frame. Fitting an insulated airtight box with a raised access step radically eliminates this thermal bridge and the mould.

How do you keep the loft ventilated without the wind displacing the insulation?

Outside air entering through the eaves grilles must not blow directly onto the layer of loose-fill insulation. Install rigid baffles in wood or waxed cardboard, inclined between each rafter, fixed from the wall plate up to ten centimetres above the level of the finished insulation. This device guides the airflow along the rafters towards the open ridges or ventilation tiles without any risk of pushing back the light fibres.

What are the rules for laying a walkway without a thermal bridge?

The technical inspection walkway must never crush the loose-fill insulation, so as not to reduce its insulating capacity. Fix raised timber battens by means of brackets or spacers fixed to the load-bearing frame, so as to leave a clear gap above the blanket. Then lay rigid, non-slip wood-based panels at least 40 cm wide, allowing safe access to the chimney stacks.

Texts and standards cited

  • CO art. 365material and ground: the contractor is liable for the good quality of the material he supplies; if the material supplied by the client or the ground designated by him is found to be defective, or if any other circumstance endangers the proper or timely execution of the work, he must inform the client immediately, failing which he bears the consequences (para. 3).
  • OTConst art. 25openings in floors: those that present a risk of falling must be fitted with a perimeter guardrail or a break-resistant, securely fixed cover.

In the same section