Key takeaways
- The installation torque prescribed in the ETA guarantees expansion without deforming the steel shank.
- An over-tightened anchor plasticises the metal and breaks the friction cone in the concrete.
- The calibrated torque wrench remains the only tool authorised to validate the final tightening.
- Releasing the wrench spring after use prevents measurement drift on the construction site.
The value prescribed by the ETA: balance between expansion and preload
For fixing a balustrade base plate or a light stair stringer, the European Technical Assessment, referred to by the acronym ETA, is the manufacturer's reference technical document. It precisely defines the nominal value of the installation torque, usually denoted Tinst. This torque is not a simple assembly recommendation: it represents the rotational force strictly necessary to drive the expansion cone inside the metal sleeve, thus creating the required bearing pressure against the walls of the drilled hole in the concrete.
Applying the exact prescribed value gives the design preload without damaging the components of the anchorage. Contrary to misconceptions still widespread on metalwork construction sites, tighter tightening does nothing to strengthen the fixing of the fitting. The torque converts rotary movement into axial tension in the shank. If tightening stays below the prescribed value, the sleeve does not anchor sufficiently in the concrete and the stud will slip at the first horizontal load on the handrail.
| Anchor diameter | Metric thread | Indicative prescribed torque | Main mechanical role |
|---|---|---|---|
| Diameter 8 mm | M8 | 15 to 20 Nm | Light fixing of end plates and cladding angles |
| Diameter 10 mm | M10 | 25 to 35 Nm | Bases of secondary posts and wall-mounted handrails |
| Diameter 12 mm | M12 | 45 to 60 Nm | Standard balustrade base plates subject to normal-use thrusts |
| Diameter 16 mm | M16 | 100 to 120 Nm | End posts and brackets of light metal staircases |
Handling the torque wrench and the structural damage caused by over-tightening
An over-tightened metal anchor is an anchoring element that is already damaged before the structure is loaded at all. When a metalworker forces beyond the installation specification, several invisible defects occur instantly in the heart of the concrete and in the metal:
- Crushing or excessive stretching of the shank thread, taking the steel into its plastic deformation zone.
- Partial or total fracture of the expansion cone through excessive crushing in the spacer sleeve.
- Spalling and micro-cracking of the concrete around the bottom of the drilled hole, reducing friction bond to nothing.
- Premature breaking out of a wedge of concrete at a corner or slab edge under excessive radial thrusts.
Under these conditions, the pull-out resistance of the fixing drops drastically. The balustrade seems perfectly stable at installation, but the anchorage can fail suddenly without prior deformation under an impact or crowd pressure. To eliminate this risk on the construction site, systematic use of a torque wrench with a release mechanism is the only recognised control method.
- Approach and alignmentScrew the nut on by hand, then tighten moderately with a standard flat or ratchet spanner until the metal plate is in direct contact with the concrete bearing surface, without deforming the base plate.
- Setting the torque valueUnlock the ring on the torque wrench handle, align the graduation with the exact value stated in the ETA of the installed model, then lock the locking system again.
- Continuous controlled tighteningApply a smooth, steady movement perpendicular to the tool's lever arm until the clear mechanical release is felt. Stop applying force immediately at the first click.
- Releasing the mechanismAfter completing the series of tightenings on the posts, it is essential to return the setting slider to its minimum rest value to release the internal tension of the calibrated spring.
Metrological checking of the torque wrench and site drift
On a construction site fitting balustrades or handrails, the torque wrench is subjected to severe stresses: knocks in toolboxes, exposure to the weather, falls from scaffolding height or rough handling. The most common mistake in crews is to treat this measuring instrument as a simple robust tightening ratchet. Yet the internal mechanism, generally made up of a preloaded helical spring and a release trip lever, loses its calibration under the effect of vibrations and residual mechanical stresses when it is left set between two jobs.
To keep the accuracy required when applying the nominal tightening torque specified in the European Technical Assessment, the tool must undergo regular metrological monitoring. A metalworker who applies fifty newton-metres with a wrench that is off by fifteen per cent is in reality applying either an under-load that allows the plate to slip under service loads, or an invisible overload that eats into the plastic reserve of the anchor shank or cracks the concrete cone.
| Check item | Minimum frequency | Permitted tolerance | Corrective action required |
|---|---|---|---|
| Resetting the vernier to zero after use | Daily (end of shift) | Complete release of the spring | Back off below the minimum graduation without disengaging the vernier, to avoid mechanical settling. |
| Intermediate check on a calibration bench | Six-monthly or after a drop | Deviation of 4 % or less | Check on a tightening simulator at three points of the scale (20 %, 60 %, 100 % of the useful range). |
| Official laboratory calibration certificate | Annual (according to ISO 6789) | Compliance according to accuracy class | Complete overhaul of the ratchet, replacement of wear parts and adjustment by an accredited body. |
| Visual inspection of the drive square and ratchet | Weekly | No excessive axial play or cracks | Dry cleaning; no thick greases in the release mechanism. |
The use of special bits or offset extensions also changes the effective lever arm. As soon as a barrier base fixing head requires an offset ring spanner, the distance between the anchor's axis of rotation and the point where the hand applies force is no longer the one intended by the tool manufacturer. The foreman must recalculate the setting on the vernier to compensate for this additional lever arm, otherwise destructive over-tightening is induced without the fitter's knowledge.
Damage assessment, on-site diagnosis and repair of a destroyed anchorage
Over-tightening of an anchor stud or expansion anchor rarely warns of itself through signs visible to the naked eye. The first physical sign of destructive overshoot is the tactile sensation of a nut that keeps turning without any increase in rotational resistance, indicating either stripping of the thread or forced slipping of the expansion cone through the spacer sleeve. At that precise moment, the residual load-bearing capacity of the anchor collapses, even if the metal base plate seems firmly held against the slab.
In the concrete, the excessive radial force generated by a sleeve pushed beyond its nominal travel produces splitting stresses that exceed the tensile strength of the material. This phenomenon is particularly critical at the edge of a balcony slab: internal micro-cracking spreads from the bottom of the drilled hole towards the free edge. Even if the crack does not immediately reach the surface, the conical failure surface of the concrete has been initiated, preventing any transmission of the dynamic loads imposed by a regulatory impact on the handrail.
- Immediate neutralisation of the failed anchorageNever attempt to re-tighten an anchor that turns indefinitely or whose shank shows visible plastic elongation. Mark the defective anchorage with industrial marking crayon to prevent its inclusion in the balustrade's restraint system.
- Dismantling and recording of the damageRemove the metalwork plate. Extract the damaged stud if the geometry allows, or cut off the threaded part flush with the concrete without damaging the bearing surface. Use an inspection magnifier to check that there are no radiating cracks around the drilled hole.
- Selecting the replacement solutionIf the surrounding concrete is intact, fill the drilled hole with non-shrink structural repair resin mortar. Install the new anchor respecting the minimum distances prescribed by the European Technical Assessment, either by geometrically shifting the drilling of the plate, or by using a chemical anchor with a bonded threaded rod allowing smaller spacings.
- Documented tightening to the prescribed torqueResume the assembly operation, checking that the drilled hole is clean, dust removed with a hand pump and brush. Apply the installation torque strictly calibrated with a checked torque wrench, without any dynamic impulse at the end of rotation.
Rigorous management of tightening torques is the legal and technical guarantee that light metal structures will hold properly. In the acceptance records of a balustrade, the written recording of the values applied, identifying the measuring instrument used and its calibration serial number, relieves the installing company by attesting that the fixings suffered no prior structural damage during assembly.
Repair protocol after failure and traceability of tightening
When fixing a balustrade, a handrail or a light stair stringer, over-tightening is a hidden ruin of the mechanical connection. If the tightening torque prescribed by the European Technical Assessment (ETA) is exceeded, the threaded rod undergoes irreversible plastic elongation while the expansion cone generates destructive radial stresses. The concrete micro-cracks inside the drilled hole and loses all frictional bond. As soon as a nut turns without locking or a wrench does not release, the anchorage is technically dead. Trying to make up for it by forcing further or by hiding the damaged rod directly endangers the safety of users.
- Making safe and removalThe metalwork element is removed immediately. The stretched or distorted metal stud must under no circumstances take the service loads of the structure again.
- Diagnosis of the edge concreteThe metalworker sounds the area with a hammer. The appearance of radial cracking or an edge spall requires the drilled zone to be permanently ruled out.
- Sealing off the failed drilled holeThe old hole is cleaned, then filled under pressure with a non-shrink grout to restore the continuity and compactness of the concrete.
- Setting out the replacement pointThe new anchor is drilled at a minimum distance corresponding to the ETA requirements, as a general rule at least double or triple the embedment depth.
If the geometry of the welded plate allows no shifting of the axis on the slab, the repair requires adapting the metal part in the workshop or using resin anchoring with a larger-diameter rod. In accordance with the rules of the art and standard SIA 118, this modification requires strict checking of the spacings and of the distances to the slab edges. Rigorous use of a checked torque wrench — verified annually by an approved calibration body — guarantees the exact application of the required torque. On the construction site, the metalworker handles the tool in line, without jerks, and stops applying effort at the first mechanical click.
Frequently asked questions
Can an impact wrench be used to bring a metal anchor close to its final tightening?
The use of the impact driver is prohibited for the final tightening of metal expansion anchors. This tool generates uncontrollable torque peaks that instantly exceed the torque prescribed by the ETA, stripping the threads or destroying the anchoring cone in the concrete. The approach can be done by hand or with a standard driver at slow speed, but the final tightening must be carried out exclusively with a manual torque wrench.
Why must a metal anchor never be re-tightened a few weeks after installation?
After the initial tightening to the prescribed torque, the concrete undergoes a natural relaxation phenomenon under the pressure of the expansion cone, which causes a slight drop in residual tension. If a metalworker applies the nominal torque again to a stabilised anchor, this causes a second phase of expansion that can crack the edge concrete and destroy the mechanical bond. Only an inspection procedure specified by the manufacturer permits a check without over-tightening.
How can the reliability of a torque wrench be quickly checked on the construction site?
The foreman first makes sure that a valid calibration sticker is present, attesting to a metrological check carried out less than twelve months ago. He then checks that the vernier returns smoothly to zero after use, to avoid fatigue of the internal spring. On the construction site, comparing two calibrated wrenches on a comparison bench or a test fixing makes it possible to spot an obvious discrepancy immediately before fitting the balustrades.
What should be done if the concrete spalls at the slab edge during tightening to the nominal torque?
Spalling of the slab edge indicates that the edge distance prescribed by the ETA has not been respected, or that reinforcement too close by has deflected the anchor. The operation must be stopped, the post removed and site management informed. The anchorage must be moved towards the inside of the slab or replaced by a made-to-measure plate with injectable chemical anchoring without expansion stress, after cleaning out and patching the chipped concrete.
Texts and standards cited
- SIA 118General conditions for the execution of construction work
