Key takeaways
- Fixing on top of the slab remains the safest technical solution by default.
- Side fixing increases the lever arm and multiplies the pull-out force on the upper anchors.
- The slab edge has an unreinforced zone that is very sensitive to the risk of spalling under load.
- The edge distances of the concrete necessarily govern the sizing of the base plates and anchors.
The lever arm turns the horizontal thrust into critical pull-out at the slab edge
The choice of how a railing is installed too often comes down to a purely aesthetic reflex or a wish to gain a few square centimetres of usable balcony area. Yet from a structural point of view, fixing a balustrade face-on against the slab edge creates a much less favourable mechanical situation than fixing on top of the concrete. The horizontal forces defined by standard SIA 261 and the geometric requirements of standard SIA 358 apply at the handrail, located at least one metre above the finished floor. With side fixing, this point of application is shifted much higher relative to the centre of rotation of the base plate.
- Anchor lever arm
- Vertical distance between the point of impact of the horizontal load on the handrail and the pivot point of the fixing plate, directly determining the overturning moment transmitted to the anchors.
With slab-top installation, the guard height is 1000 mm. The plate rests flat, and the anchors work mainly in shear and direct tension, with a lever arm limited to the height of the post. As soon as you move to the slab edge, the post runs down along the concrete edge face. The handrail is then 1100 mm, or even 1250 mm, above the fixings depending on the slab thickness and the available cover. This extra height mechanically lengthens the lever arm. The resulting overturning moment increases proportionally, transferring a massive pull-out stress to the upper anchoring point of the plate.
| Mechanical criterion | Slab-top installation (flat) | Face-fixed installation (slab edge) |
|---|---|---|
| Effective lever arm | approx. 1.00 m (rail height) | 1.15 m to 1.30 m depending on slab edge |
| Main type of loading | Shear + moderate tension | High tension on upper anchor |
| Vertical spacing of fixings | Can be sized generously on the plate | Restricted by slab thickness |
| Sensitivity to casting tolerances | Low (can be compensated by shimming) | High (formwork out of plumb) |
The problem is made worse by the reduced vertical spacing between the anchors of the side plate. On a standard slab 180 to 200 mm thick, the spacing between the upper and lower anchors rarely exceeds 100 to 120 mm if the concrete cover distances are respected. To balance the overturning moment increased by crowd thrust or wind, the resisting couple has a very small lever arm. The pure tensile force on the upper anchor can thus reach two or three times that measured on a plate installed on top of the slab.
Edge distances and concrete breakout: why slab-top fixing remains the reference choice
Reinforced concrete has very heterogeneous characteristics depending on where the drilling is done. The edge of a balcony slab is the most fragile zone of the load-bearing element. Often poorly vibrated at the edge during casting, prone to gravel pockets and lightly reinforced on its vertical face, the slab edge presents an acute risk of spalling under anchor loads. The concrete cone failure phenomenon, inherent to the behaviour of expansion anchors or even chemically bonded threaded rods, immediately finds a free surface towards the outside.
To avoid breakout of the substrate, the technical approvals of anchoring systems impose critical edge distances and minimum distances. At the slab edge, the tradesperson must respect the distance to the upper edge, to the lower edge and laterally to the balcony corners. If waterproofing or a floating screed sits on top of the structural work, the metalworker is often forced to drill into the last fifty millimetres of sound concrete available, which breaches most of the technical data sheets of chemical anchor suppliers. The risk of an entire piece of concrete breaking away then becomes permanent.
- Checking the reinforcement layoutCheck the actual position of the edge bars and the edge stirrup before validating the position of a side plate.
- Measuring distances to free edgesConfirm that each drill hole respects the minimum edge distance defined by the anchor supplier for non-cracked concrete.
- Prefer flat fixingSystematically choose installation on top of the slab, protected by the full thickness of the slab, whenever the waterproofing allows it.
- Use of offset platesIf side fixing is imposed by the architecture, design U-shaped or bracket plates to take the forces set back from the slab edge.
Checking the concrete substrate and slab edge geometry
Face-fixing on a slab edge requires the full thickness of the finished floor build-up to be taken into account from the survey stage. Standard SIA 358 prescribes a minimum protection height of 100 cm measured from the finished walkable surface to the top edge of the handrail. When the raw slab receives a floating screed, a layer of thermal insulation, waterproofing or paving slabs on pedestals, the actual walking level is raised by 12 to 25 cm relative to the load-bearing concrete. This increase directly lengthens the vertical posts and the lever arm applied to the anchors.
This geometry affects the position of the upper bolt of the plate. To retain sufficient rigidity without deforming the metal section, the plate frequently extends down along the slab edge. The metalworker must then work with a tight anchoring zone, located at mid-height of a slab edge whose usable thickness rarely exceeds 20 to 24 cm. In a slab edge 20 cm thick, drilling two superimposed rows of anchors while keeping a sufficient minimum distance from the slab edge relative to the upper and lower edges becomes a delicate geometric problem.
The execution tolerances of the structural work are another pitfall. A slab edge cast on the construction site frequently shows flatness defects, vertical deviations or alignment swings of 10 to 20 mm between two columns. Compensating for this misalignment by shimming under a side plate immediately changes the bending force carried by the bonded threaded rods, reducing their permissible pull-out resistance.
Technical trade-off between side fixing and slab-top installation
The choice between fixing on top of the slab and face-fixing on the side does not depend solely on architectural criteria of floor area. It determines how the concrete works mechanically and the durability of the anchorage in the face of the risk of concrete spalling. On top of the slab, the anchors benefit from the full mass of the slab, in a zone where the concrete works mainly in compression under the plate supports, naturally set back from the outer edges.
Conversely, side anchoring converts the horizontal service thrust defined by the technical standards into a direct pull-out couple on the upper fixing and a point thrust on the lower fixing. If the upper bolt is too close to the top edge of the slab, the tension exerted tends to shear the concrete prism outwards. If the lower point is too close to the bottom edge, the bearing reaction can break out the rounded edge or chamfer of the slab edge, particularly where a drip groove is built into the formwork.
| Installation criterion | Slab-top fixing (flat) | Side fixing (face-fixed) |
|---|---|---|
| Lever arm on the plate | Limited to the post height (100 cm) | Increased by the thickness of the finished floor (115 to 130 cm) |
| Concrete zone stressed | Central mass of the slab, direct compression | Slab edge, tension zone close to the edges |
| Minimum edge distance | Easy to respect (plate set back by 80 to 120 mm) | Critical (high stress on upper and lower edges) |
| Risk of concrete spalling | Low, limited breakout if spacings are respected | High, expulsion of the concrete corner by cone effect |
| Interference with waterproofing | Direct penetration of the screed and waterproofing | Avoids the roof build-up but penetrates the insulated slab edge |
Given these constraints, slab-top fixing remains the reference solution for the metalworker where no flat-roof waterproofing requirement prevents it. Where face-fixing is necessary to preserve a waterproofing upstand or to maximise the usable area of a balcony, the use of injection chemical anchoring mortars without mechanical expansion stress becomes essential. These systems limit radial pressures in the concrete during tightening, reducing the likelihood of cracking along the end reinforcement.
Handling drilling surprises and remedial protocols at the slab edge
On the construction site, drilling into the slab edge for a face-fixed installation often reveals surprises: reinforcing bars too close, porous concrete or sudden spalling of the edge. When the edge breaks out or a crack propagates under percussion, the load-bearing capacity of the fixing is destroyed. The metalworker must never try to fill the area with rapid mortar to re-set an anchor there. The force required by standard SIA 358, combined with the long lever arm of the side bracket, would pull out the cracked concrete cone at the first transverse impact.
- Immediate stop and joint inspection recordStop drilling as soon as cracking appears or if there is repeated contact with a main reinforcing bar. Mark the location, photograph the slab edge and formally notify site management and the civil engineer of the situation.
- Reinforcement detection and probingRun a magnetic detector to map the actual reinforcement. If the reinforcement prevents reaching the required depth without risking cutting the load-bearing steel, prohibit any destructive core drilling without written authorisation from the engineering office.
- Adapting the plate or switching installation methodOn the engineer's advice, either lengthen the vertical plate to bring the lower anchor out of the damaged zone, or change the anchoring method by switching to a top fixing on the slab using made-to-measure shoe plates.
Where the geometry of the structural work makes it impossible to respect the edge distances, the metalworker must refuse the side installation. Installation on top of the slab then becomes the required choice, ensuring conical dispersion of forces into the mass without risking spalling.
Frequently asked questions
What should be done if an anchor causes the concrete to break out when tightened at the slab edge?
Stop tightening immediately and above all do not fill the spall with mastic. The anchorage is totally compromised. Record the incident in writing with site management and the civil engineer. The technical solution generally consists of designing a taller metal plate to anchor lower in the sound mass, or moving the side post to switch to installation on the top face of the slab.
Why prefer slab-top installation over slab-edge installation outdoors?
Slab-top installation remains the reference because the fixings work away from free edges, eliminating the risk of concrete spalling under the effect of the lever arm. In addition, drilling the outdoor slab edge often passes through zones of reduced cover exposed to frost and carbonation. Top fixing also simplifies liquid or bituminous waterproofing upstands, whereas side anchoring creates horizontal penetration points that are very sensitive to water ingress.
How should you react if the concrete reinforcement blocks drilling of the side plate?
It is strictly forbidden to cut a reinforcing bar with a concrete drill bit without the prior agreement of the civil engineer. Use a rebar detector to locate the actual grid. If no vertical offset is possible on the original plate, have the manufacture of an adapter plate with slotted holes or modified spacings approved. If the conflict persists along the entire façade, request a contractual change to slab-top fixing.
Does standard SIA 358 allow fixing plates to be adapted on the construction site?
Standard SIA 358 sets the requirements for containment and impact resistance without prohibiting the adaptation of parts, provided that the overall mechanical strength remains guaranteed. Any trimming, slotting or additional drilling of a plate in a site workshop must be subject to a recalculation of the lever arm and a stiffness check. Modifications to galvanised steel also require immediate anti-corrosion treatment with zinc-rich paint.
Texts and standards cited
- SIA 358Railings: safety requirements, geometric dimensions and restraint forces
- SIA 118General conditions for the execution of construction work
