Skip to content
Website
🧱 CFC 274Section 2 of 610 chapters

Railing loads and sizing: the execution framework

Sizing a metalwork railing is not a matter of visual intuition but of rigorous verification of the mechanical stresses. This section provides team leaders and site foremen with the essential reference points to calculate the service thrust according to the use of the building, control the bending moment at the foot of the posts, anchor the base plates securely and check the deflection under load, in full compliance with standard SIA 358 and standard SIA 261.

  • 10chapters
  • 22 000words
  • 6sections in the training course
  • 60chapters in total

Key values to remember 5

norme SIA 261

0.8 kN/m

Minimum characteristic line load at handrail level in private dwelling areas

norme SIA 261

1.6 kN/m

Minimum line load for gathering areas, shops and high-traffic spaces

norme SIA 358

1.0 m

Minimum protective height of a railing for a fall height of up to 12 metres

norme SIA 358

1.1 m

Minimum protective height of a railing where the fall height exceeds 12 metres

norme SIA 358

30 mm

Maximum permitted horizontal deflection at the top of the railing under service load

Scope of application and work boundaries in metalwork

The mechanical sizing covered here concerns exclusively building metalwork and light metalwork in finishing work (CFC 274). It applies to interior and exterior railings, stair handrails, mezzanine balustrades, balcony dividers and handrails fixed to walls. These elements perform a strict function of restraining people to prevent falls from height, without contributing to the overall stability of the structural work.

The professional boundary with the other building trades in Switzerland must remain perfectly clear:

  • Load-bearing steel construction (CFC 215): steel frames, main beams, composite floors, mixed façade frameworks and heavy structural connections fall under the steel construction contractor and the civil engineer.
  • Windows and façades (CFC 221): glazed external joinery incorporating fixed railing functions or openable fanlights belongs to the façade contractor.
  • Interior doors and door assemblies (CFC 273): interior closures and technical lobbies do not share the horizontal thrust criteria of the balustrade.
  • Workshop anti-corrosion surface treatment (CFC 215) and finishing paint (CFC 272): initial hot-dip galvanising or powder coating belongs to heavy fabrication, whereas paint touch-ups on the construction site are assigned to the painter.
  • Structural anchorages in the structural work (CFC 211.1): the mason or concrete worker sizes the reinforcement of the host concrete; the metalworker sizes only the anchor and the base plate to transmit the force without spalling the edge of the substrate.

The CFC 274 metalworker bears responsibility for the mechanical strength of their own work. They must be able to justify every selected section, every workshop welded connection and every fixing point by a consistent calculation note or by reference to proven standard details.

Step-by-step approach to sizing and checking a railing

The design and installation of a railing require a sequential approach that starts from the actual use of the building and ends with validation on the completed work. Each decision directly influences the next link in the chain of force transmission.

  1. Identify the basic loadSizing must always start with determining the horizontal thrust at handrail level according to the intended use of the premises, distinguishing a private dwelling from a building open to the public in accordance with standard SIA 261.
  2. Calculate the post frameworkThe cumulative line load over the post spacing generates a maximum bending moment at the base of the post. The section of the profile (square tube, flat bar or hollow section) must have a sufficient section modulus to resist without permanent deformation.
  3. Decide on the fixing arrangementThe choice between a top-of-slab fixing and a side-mounted fixing radically changes the lever arm, the tension on the upper anchors and the critical distance to the concrete edges needed to avoid spalling.
  4. Size the base plate and the fixingsThe thickness of the base plate must prevent any parasitic lever effect or warping under load, while the number and spacing of the anchor bolts must resist the calculated overturning moment.
  5. Incorporate the requirements for structural glassIn the absence of metal posts, the glass embedded at its base absorbs all of the loads. The thickness of the toughened laminated panes, the accuracy of the continuous setting and the provision of an attached handrail ensure residual safety after breakage.
  6. Check stiffness at the serviceability stateResistance to failure is not enough: the deflection under service thrust must remain within the limits of standard SIA 358 to avoid any unsettling feeling of flexibility, which systematically leads the user to reject the work.
  7. Take climatic loads into accountAn opaque or semi-solid infill in perforated sheet metal or glazing turns the balustrade into a screen against the wind. On an exposed balcony on a high floor, the aerodynamic pressure according to standard SIA 261 often exceeds the standard service load.
  8. Secure gathering areasStadiums, multipurpose halls and public footbridges are subject to dynamic crowd loads. The design factors and anchorages must be reinforced, without transposing the dimensions used for residential housing.
  9. Compile the justification fileEvery installed work must be backed by a verifiable calculation note, anchor technical data sheets and workshop drawings recorded in the work file, serving as legal protection in the event of an incident according to art. 229 CP.
  10. Carry out destructive or non-destructive testing in situIn case of doubt about the resistance of a fixing assembly, or at the request of site management, a thrust test with a jack and dial gauge validates the permissible deformation and a perfect elastic return.

📘 Chapters in this section 10

Balustrade loads and sizing

Thrust load: value by usage category, housing versus public place

Distinguish the thrust loads between housing and public places to avoid any initial structural under-sizing.

Balustrade loads and sizing

Posts: spacing, section, fixity and base moment

Calculate the post spacing and the bending moment at the foot to fix the required steel section.

Balustrade loads and sizing

Side-mounted or face-fixed: lever arm, slab edge and concrete spalling

Master the effect of the lever arm and protect concrete edges against the risk of spalling.

Balustrade loads and sizing

The base plate: thickness, number of bolts, position and visible deformation

Determine the base plate thickness and the anchor spacing to eliminate visible deformation under load.

Balustrade loads and sizing

Structural glass: channel profile, thickness, and the handrail that remains mandatory

Install embedded structural glass while complying with the normative requirement for a continuous connecting handrail.

Balustrade loads and sizing

Deflection: permissible value, perceived flexibility and occupant complaints

Limit the deflection under thrust to eliminate the feeling of flexibility that is responsible for disputes at acceptance.

Balustrade loads and sizing

Solid infill: wind exposure, additional load and exposed balcony

Calculate wind thrust on solid or perforated infills on balconies heavily exposed to the weather.

Balustrade loads and sizing

Public place: crowd loading, grandstand, and the guardrail you must not copy from housing

Adapt sections and fixings to intense crowd thrusts in stands and public buildings.

Balustrade loads and sizing

Justifying your work: calculation note, validated standard detail and retained file

Prepare the calculation note and archive the technical justifications to legally secure your workshop's liability.

Balustrade loads and sizing

Testing in place: applied load, deflection measurement, elastic recovery and test record

Carry out an in-situ load test with a jack and dial gauge and record a compliant test report.