Key takeaways
- SIA 358 prohibits horizontal rails that form footholds for children.
- The non-climbable zone extends from the finished floor up to the regulatory safety height.
- A climbable railing systematically results in the municipal occupancy permit being withheld.
- Backing with sheet metal or laminated glass neutralises the ladder effect without replacing the original posts.
Understanding the non-climbable zone to neutralise the ladder effect in metalwork
On balconies and loggias of dwellings, the architectural choice of an infill with horizontal rails often collides directly with the need to protect users. When a child can place a foot on a low crossbar and then continue climbing on the intermediate rails, the railing loses its restraining function and becomes an aid to climbing over. SIA 358 defines these mechanisms precisely in order to prevent falls from height, particularly where the fall height exceeds the usual limit values for residential buildings.
- Ladder effect
- Arrangement of horizontal or inclined structural elements providing successive footholds or handholds that make it easier for a young child to climb a railing.
To prevent this phenomenon, SIA 358 requires a continuous non-climbable zone. Between the finished balcony floor and a minimum protection height, the infill must not include any element offering a usable horizontal bearing surface. Metal rails welded or screwed to the posts almost always create a bearing surface wider than two centimetres, which is technically enough to support the front of a small child's foot.
| Infill configuration | Ladder effect risk | Compliance in private housing | Preventive action in the workshop |
|---|---|---|---|
| Horizontal round or square rails | Critical and immediate | Non-compliant without protection | Propose a variant with vertical bars |
| Horizontal tensioned stainless steel cables | Medium to high depending on tension | Rejected by the building control authority | Replace with a square-mesh net |
| Vertical balusters (max. gap 120 mm) | None (no foothold) | Fully compliant | Check the clear spacing between bars |
| Solid sheet or flush perforated sheet | None if perforations are suitable | Fully compliant | Check the diameter of the perforations |
In day-to-day practice in the metalwork workshop, the temptation is great to follow the architect's drawing blindly without checking the intended use of the premises. As soon as the work serves a rental building or a family house, the craftsman must report in writing the conflict with the prevention rules of SIA 358. Responsibility for the geometric design rests on the fabrication drawings that the foreman approves before the sections are cut.
Dealing with the non-compliance finding and adapting the work before the occupancy permit
The acceptance inspection by the municipal building control authority is the final deadline of the construction site. If the inspector finds climbable horizontal rails on the façades, the administrative sanction follows without delay: the occupancy permit is refused or suspended until the work has been fully remedied. This blockage prevents tenants or owners from moving in, causes major financial penalties for site management and triggers an immediate dispute under the Code of Obligations against the installing metalworker.
- Geometric diagnosis on the balconyMeasure the clear height between the finished floor covering and the first rail. Record the width of the section profiles and the vertical distance between each intermediate crossbar in order to quantify the climbing zone.
- Selecting an approved remedial solutionDecide whether the work should receive an inner backing with a solid panel or whether complete replacement of the frame is more economical. Have the remediation principle approved by site management.
- Installing the safety backingFit, on the inner side of the balcony, a two-millimetre perforated aluminium sheet or a laminated safety glass panel clamped onto the existing posts. The screen must conceal the rails up to the height required by the standard.
- Joint inspection record and lifting of reservationsCall in the supervisory authority to verify the removal of every foothold. Obtain written approval of the arrangement in order to release the authorisation to occupy the dwellings.
In the event of a serious dispute, the client may demand the outright removal of the non-compliant balustrades. To avoid this destructive outcome, the metalwork site foreman should always favour a continuous cladding on the inner face. This smooth surface neutralises mechanical access to the horizontal bars while keeping the primary framework, the anchor plates and the handrail already in place.
Geometry of footholds and configuration of horizontal profiles
On a residential construction site, the architectural wish to lighten the look of a façade regularly leads to the specification of metal railings made of continuous rails or horizontal flat bars. When horizontal balusters are installed along an open edge, each continuous element provides a direct foothold for climbing. According to SIA 358, a railing must not only delimit the drop and restrain users, it must also be designed so as to prevent climbing by young children. As soon as a horizontal profile offers a flat surface large enough to place the tip of a foot, the ladder effect exists, making the work inherently dangerous.
The foothold is assessed from the walkable level of the balcony, taking into account the slab edge downstand, the concrete plinth or the lower crossbar of the metalwork. Any horizontal step or offset deeper than two centimetres in the lower critical zone provides a seat suitable for starting a climb. Superimposed continuous bars, typically spaced ten to fifteen centimetres apart for geometric reasons, form an immediate technical ladder. To comply with SIA 358 without giving up the horizontal lines on the outside, the metal constructor must eliminate any accessible projection on the inner face of the balustrade.
| Baluster configuration | Usable foothold projection | Compliance with SIA 358 | Implication for the work |
|---|---|---|---|
| Round tubes welded on the inner face | Greater than 20 mm | Non-compliant (direct ladder effect) | Categorical refusal at final inspection |
| Horizontal flat bars welded between posts | 30 to 50 mm of flat depth | Non-compliant in the lower critical zone | Climbing made easier, technical rework mandatory |
| Bevelled profiles with a slope greater than 60° | None (shoe slips off immediately) | Compliant subject to regulatory spacing | Made to measure, increased machining cost |
| Outer rails backed by a smooth inner wall | None (closed vertical surface on the slab side) | Fully compliant | Permanent neutralisation of any foothold |
Municipal inspection procedure, permit refusal and emergency replacement
During the official acceptance inspection by the municipal building control authority, checking the metalwork is a decisive step towards obtaining the occupancy permit. The inspector checks the railing height, the size of residual gaps and the complete absence of a ladder effect on all balconies and loggias. As soon as climbable horizontal rails are found in the sensitive lower zone, the finding of non-compliance is notified. The municipal authority refuses to issue the occupancy permit as long as a climbing hazard remains, contractually blocking the handover of keys to tenants or purchasers.
- Notification of the refusal and survey of the workReceipt of the official report of the building control authority stating the non-compliance of the balconies, followed by a joint inspection record on site with the representative to measure the exact height of the footholds in question.
- Choosing between adaptation and complete removalAnalysis of cost-effectiveness and lead times between complete dismantling of the elements to refabricate vertical balusters in the workshop and modification on site by adding a continuous vertical solid screen.
- Installing a neutralising inner shieldMechanical installation, on the inner face of the posts, of continuous panels of laminated safety glass or solid powder-coated aluminium sheets, preventing any physical access to the existing horizontal rails.
- Follow-up inspection and lifting of municipal reservationsCalling in the municipal services to inspect the technical modification, verify the absence of any foothold up to the required height and issue the final occupancy permit.
Where the addition of an inner backing is rejected by site management because of excess weight or visual alteration of the building envelope, outright replacement becomes unavoidable. The installation team must cut out the offending horizontal profiles on site or unbolt the complete frames in order to install a vertical structure that complies with the fall-prevention directives.
Crisis management on the construction site: permit refusal and emergency rework
The refusal of the occupancy permit by the building control authority almost always comes a few days before the handover of the keys. The municipal inspector finds horizontal rails forming successive footholds in the non-climbable zone defined by SIA 358. The consequence is severe: a formal ban on occupying the dwellings as long as the railing has a ladder effect amounting to a fall hazard for young children. The metalwork contractor and site management are under maximum pressure to lift the objection without blocking the overall handover.
- Immediate protective measureFit a temporary inner backing of solid polycarbonate sheets screwed to the existing metal posts to neutralise the footholds before the authority's second visit.
- Technical decision for a lasting solutionChoose between complete replacement of the balusters with compliant vertical bars or the permanent fixing of a solid laminated glass or perforated sheet panel on the inner side.
- Formal confirmation of complianceHave site management certify the elimination of every foothold over the regulatory height and obtain the acceptance certificate from the building control authority.
An urgent railing modification requires rigorous coordination in the workshop to cut the flats, weld the inserts and ensure express powder coating. If the load-bearing structure of the railing remains sound, the metalworker favours fitting a smooth inner screen that removes every climbing point while keeping the primary framework. Where the original geometry makes any cladding impracticable or unsightly for the architect, complete dismantling and replacement with prefabricated frames with vertical infill remain the only way to release the occupancy permit in accordance with good practice.
Frequently asked questions
Does a perforated sheet fitted flat prevent the ladder effect on a railing?
Yes, provided that the diameter of the perforations or the mesh size is smaller than the dimensions that would allow the tip of a child's foot to be inserted. Fitted on the balcony side, it completely neutralises the horizontal rails behind it. The metalworker must make sure that the gap between the sheet and the slab edge does not create any new accessible foothold in the critical zone defined by SIA 358.
Can horizontal rails spaced less than 100 millimetres apart be installed on a balcony?
No. Even if the reduced spacing prevents the passage of the body or head, it creates a genuine ladder for small children. In the non-climbable zone, any surface offering a horizontal foothold is prohibited by SIA 358, whatever the spacing of the crossbars. The municipal inspector systematically refuses the occupancy permit for such an arrangement.
Who bears the financial cost of replacing the railing rejected by the building control authority?
The allocation depends on the execution phase and the detail drawings approved. If the metalworker manufactured the work according to faulty architect's drawings without giving formal notice, their professional liability is engaged jointly with that of the representative. If the craftsman changed the spacing or the arrangement of the profiles in the workshop on their own initiative, the cost of the rework falls entirely on them.
Does laminated glass fixed to a railing with rails resolve the occupancy refusal?
Fitting laminated safety glass on the inner side immediately resolves the non-compliance because it removes physical access to the horizontal rails. This solution avoids complete removal of the metal framework. However, the glazing clamps must be sized and the load-bearing capacity of the existing posts checked to take the new wind loads generated by the now solid glazed surface.
Texts and standards cited
- norme SIA 358Railings: safety requirements for height, openings and protection against climbing
- norme SIA 118General conditions for the execution of construction work and management of defects in the work
