Skip to content
Website
🧱 CFC 274Balustrade loads and sizingChapter 5 of 10 in the section

Structural glass: channel profile, thickness, and the handrail that remains mandatory

This chapter details the design and installation rules for structural glass balustrades fixed at the base. The metalworker learns how to select the appropriate channel profile, define the laminated safety glass build-up to withstand horizontal loads, and incorporate the continuous handrail required to prevent toppling.

Key takeaways

  • The continuous channel profile absorbs the entire bending moment generated at the top of the glazing.
  • The SIA 358 standard requires a minimum balustrade height of one metre with no climbable gap.
  • Toughened laminated glass ensures residual safety thanks to rigid structural interlayers.
  • An integral handrail links the panels together to prevent an open drop should a glass pane fail.

Transfer of forces to the channel profile and requirements for laminated glass

In a structural glass balustrade without posts, each glass panel acts as a vertical cantilever fixed at its base. The whole horizontal thrust applied at the top of the balustrade, whether wind pressure on an outdoor terrace or the crowd load defined by the design standards for load-bearing structures, results in a considerable overturning moment at the lower rebate. Unlike a traditional baluster system in which the posts distribute point loads onto welded base plates, the fine metalwork of CFC 274 must here ensure a continuous distribution of stresses into the structural work by means of an extruded aluminium or stainless steel U-profile.

The glazing build-up must not be improvised. A single monolithic toughened pane is ruled out for these applications, because its instantaneous breakage would immediately open up the drop. The metalworker systematically installs laminated safety glass made of at least two sheets of toughened or heat-strengthened glass, bonded together by one or more interlayer films. In exterior metalwork exposed to sun and moisture, a rigid, high-adhesion ionoplast interlayer is preferred over standard polyvinyl butyral. This technical film provides optimal mechanical coupling between the two glass sheets and guarantees residual load-bearing capacity in the event of partial breakage, preventing the panel from sagging like a flexible sheet.

Usual structural glazing build-ups according to exposure and loads
Type of structureMinimum thicknessGlass build-upInterlayer type
Private indoor dwelling17.52 mm (88.4)Thermally toughened glass (ESG)Polyvinyl butyral (PVB)
Residential outdoor balcony21.52 mm (1010.4)Thermally toughened or heat-strengthened glass (TVG)Ionoplast or structural PVB
Public-access building25.52 mm (1212.4)Thermally toughened glass with heat-soak testRigid ionoplast

Anchoring the channel rail in the concrete slab requires rigorous precision. The fixing spacing, strict compliance with the distance to the slab edge and levelling of the rail determine how the structure withstands pull-out forces. The metalworker inserts adjustment shims and specific elastomer gaskets along the rail to prevent any direct contact between the glass and the metal, since such localised contact risks initiating irreversible thermal or mechanical breakage.

Role of the safety handrail and assembly techniques

On a freestanding glass balustrade, installing a continuous integral handrail is an essential safety redundancy measure. Even with laminated glass sized to carry the service loads, the simultaneous breakage of the components of a panel under accidental impact creates an immediate breach in the physical barrier. By mechanically linking all the glass panels together and anchoring at the ends against adjacent walls or return corners, the handrail acts as a continuous beam that compensates for the absence of load-bearing posts.

Residual safety provided by the handrail
A continuous metal device fixed to the top edge of the glass panels that transfers the horizontal thrust to the adjacent intact sections if a glass element were to shatter, thus preventing the person leaning on it from falling into the void.
  1. Checking the alignment of the top edgesCheck the levelling of the top edge of the panels with a laser level before any final tightening of the retaining shims in the base channel.
  2. Fitting the protective gasketInsert a continuous EPDM elastomer gasket or a plastic centring profile on the top edge to rule out direct steel-to-glass contact.
  3. Fitting the metal profileSnap on or slide on the stainless steel or aluminium handrail profile, fitted with a groove suited to the total thickness of the laminated glazing.
  4. Fixing and tying in at the endsMechanically connect the handrail sections with internal splice plates and anchor the returns rigidly into the load-bearing masonry.

Several profiles are commonly fabricated in the metalwork workshop to fulfil this tying-in function. A thin U-profile simply capping the top edge protects the glazing edge against everyday impacts, preventing superficial chipping of the toughened glass, which impairs its structural balance. Alternatively, a round or square brushed stainless steel tube mounted on offset brackets provides a grip that complies with accessibility recommendations without obscuring the visual transparency of the top of the glazing.

For pricing and estimating the supplies for specific profiles or structural laminated glazing, the site manager consults the section dedicated to tenders. The fixing details must incorporate components resistant to aggressive outdoor atmospheres in order to prevent any galvanic corrosion between the guide rail and the stainless steel assembly fasteners.

Fixing to the structural work and resisting the overturning moment

In an all-glass balustrade fixed at the base, the horizontal thrust applied at the top results in a considerable overturning couple on the anchor profile. Unlike traditional metalwork with spaced posts, the continuous extruded aluminium or steel profile transmits the bending forces almost continuously to the reinforced concrete slab. The anchorage to the structural work is the critical point of the structure, because the internal lever arm between the compression line and the tension line of the profile generally does not exceed eight to twelve centimetres for a standard balustrade height as defined by SIA 358.

To resist the pull-out forces concentrated on the row of anchors on the inner side, the metalworker must strictly observe the prescribed distance to the slab edge for each stud or threaded rod set by injected resin mortar. Positioning too close to the edge weakens the concrete failure cone and compromises overall resistance under service loads. Levelling of the profile requires incompressible metal packing under each anchor point: tapered shims in polyamide or metal make it possible to compensate for unevenness in the concrete without inducing an uncontrolled overhang.

Fixing configurations of the base rail according to installation type
ConfigurationPredominant forceUsual anchor typeConstruction site point of attention
Installation on slab (flat)Pure tension and pull-out at the rear edgeThreaded rods set in two-component resinMinimum distance to slab edge to avoid spalling
Face-fixed installation (slab edge)Shear combined with upper tensionHeavy-duty anchor studs or threaded sleevesPosition of reinforcing bars when drilling with a hammer drill
Installation embedded in the screedOverall bending and lateral confinementProfile fixed before insulation with adjustable risersContinuity of drainage at the bottom of the rail and waterproofing connection

Outdoors, infiltration water entering the groove of the profile must be drained away immediately. Standing water causes premature delamination of the lower edges of the laminated glazing through permanent moisture or winter frost. The profile must be fitted with factory-milled drainage slots and installed on drainage shims raised by at least five millimetres above the rough level, to direct run-off water towards the weep holes or the waterproofing system.

Structural setting of the glazing and continuity of the handrail

The fixing of the laminated safety glass in the metal shoe relies on a dry-setting system that eliminates the traditional pouring of resin, which is difficult to rework when replacing a pane. High-density elastomer setting blocks at the bottom of the groove support the dead weight of the panels, while side gaskets fitted with pressure screws or double-wedge shims adjust the plumb. This arrangement allows the metalworker to compensate for alignment variations to the millimetre on the vertical edges and to maintain a regular open joint, generally between five and eight millimetres, preventing any direct contact between the glass edges under wind action.

The top handrail, often made as a grooved tubular profile in stainless steel or aluminium, is not purely aesthetic. It forms the continuous mechanical tie essential to the redundancy of the structure. Fixed to the top edge of the panels by means of a thermoplastic rubber seal or a continuous elastic cord, it mechanically links at least three successive panels. At the ends of the structure, the top profile must be firmly connected to the masonry or adjacent walls using end plates that are mechanically anchored.

When fitting the handrail onto laminated glass, the differential thermal expansion between the metal and the glass must be absorbed at the joints and end connections. The metalworker inserts internal sliding sleeves at the profile junctions and checks that no point stress is applied to the sharp corners of the glazing. Direct steel-to-glass contact without a resilient interlayer would cause edge chipping during structural movements or temperature variations, leading to immediate breakage of a toughened sheet.

Managing defects on the channel profile and laminated glazing

On a structural glass balustrade fixed into the floor, the slightest execution defect transfers excessive stresses directly into the glass or the anchor fixings. When defects occur during installation or after fitting, the metalworker's intervention must follow a rigorous procedure to guarantee user safety in accordance with the requirements of SIA 358.

  1. Finding a misalignment or insufficient clearanceIf two adjacent panels touch under service or thermal load, immediately loosen the structural adjustment wedges. Restore the prescribed nominal lateral clearance by interposing elastomer shims compatible with the safety interlayer in order to avoid any edge impact.
  2. Dealing with delaminated or broken glazingIf one of the plies of the laminated glazing breaks, the continuous U-profile or tubular handrail ensures the residual retention of the barrier. Remove the handrail only after installing a temporary protective barrier on the open-drop side. Replace the complete panel with glazing of identical thickness and build-up.
  3. Remedying a defective anchorage in the slabIf an anchor spins freely or if the slab edge shows spalling that compromises the edge distance, stop work on the construction site. Submit a technical report to the civil engineering office to validate relocating the drill holes or injecting a high-strength chemical anchor with extended anchor rods.

The acceptance report must record the torque-wrench check of the fixing screws of the aluminium or steel profile, the laser alignment of the safety handrail and the total absence of direct contact between the glass and the metal rail.

Frequently asked questions

Can the handrail be omitted entirely on an all-glass balustrade if the project requires it?

No. Even with thick toughened laminated glass, the SIA 358 standard requires protection against falling in the event of breakage. The continuous handrail or a rigid top profile links the panels together: if a panel shatters completely, the handrail bears on the adjacent sections to prevent a direct open drop, maintaining the mandatory residual safety.

What should be done if a laminated glass panel suffers edge chipping while the shims are being adjusted?

Any panel showing a chip, flake or crack on its edge must be rejected and replaced. Toughened glass accumulates considerable internal stresses: damage to the weakened edge zone inevitably leads to sudden breakage under wind or thrust. The metalworker must never seal or conceal damaged glass.

How can a misalignment between two adjacent panels be corrected before clipping on the top rail?

The misalignment is corrected exclusively at the level of the channel profile at floor level. Use the tapered shim system or integrated jacks provided by the rail manufacturer to adjust the plumb of each panel independently. Forcing a handrail profile onto misaligned glass induces a permanent bending stress that damages the laminated interlayer.

What should be done if the reinforcement of the concrete slab blocks the drilling of the rail anchors at floor level?

Cutting load-bearing reinforcement without the prior agreement of the civil engineer is strictly prohibited. If the drilling template meets a bar, move the anchor within the slotted hole provided in the rail or consult the supplier to validate an alternative close-spaced fixing. A non-compliant anchorage at the base immediately compromises the resistance to the overturning moment.

Texts and standards cited

  • norme SIA 358Balustrades: safety requirements, protection heights, service loads and fall prevention

In the same section