Skip to content
Website
🧱 CFC 274Gates, grilles and motorised closuresChapter 4 of 10 in the section

Security grille: burglary protection and blocked emergency exit

Fitting an anti-burglary grille on a window can turn an emergency exit into a deadly trap in the event of fire. This chapter covers the analysis of the openings concerned, the requirements for grilles that open from the inside without a key, the rooms where fixed anchoring remains excluded, and the formal drafting of your written notice to the client.

Key takeaways

  • An anti-burglary grille must never block an opening required for the evacuation of persons.
  • Basement bedrooms and rooms without a secondary exit rule out any fixed grille.
  • The opening leaf requires an internal lock that can be released manually, without an emergency key.
  • The locksmith systematically issues a written notice if the owner demands non-compliant fixed bars.

Conflict of use between delaying a break-in and emergency evacuation

On a light metalwork construction site, fitting a security grille on the face or in the reveal traditionally responds to a request for mechanical protection against intrusion. In residential buildings, administrative premises or craft workshops, openings at ground-floor level, in sunken areas or at plinth level are the weak points targeted by burglars. Yet any window accessible from the ground is at the same time a potential heat vent or an essential secondary escape route when a fire starts.

Secondary escape route
Emergency rescue route or façade opening allowing a fire-affected area to be evacuated, or persons to be rescued by the fire service, when the main escape route is filled with smoke or inaccessible.

The technical conflict arises from the contradictory requirements of burglary resistance and speed of egress. A fixed grille made of solid square bars or massive round bars of sixteen millimetres, anchored in the masonry by threaded rods set in chemical mortar or by tamper-proof metal anchors, guarantees a high delay to break-in. In return, it irretrievably traps the occupants once the internal corridors or access stairs are filled with toxic smoke.

Risk analysis according to room use and type of grille
Room useAccess configurationPermissible protective device
Habitable bedroom on ground floor or in basementSingle internal door to corridor or staircaseGrille opening from the inside without a key (mandatory)
Technical room or storeroom without workstationSeparate, signposted fire-rated external doorFixed sealed grille permissible, subject to fire service access
Workshop or office at plinth levelMain exit with risk of direct smoke ingressInternal pivoting grille that can be unlocked with one hand
Small windowless sanitary room or changing roomDirect access to a secured area or sealed airlockFixed grille tolerated if the opening is not used as an escape route

The cantonal police guidelines on crime prevention often recommend rigid reinforcement of ground-floor glazed openings. However, the locksmith's analysis must cross-check these police recommendations against the requirements of the fire authority and municipal building regulations. No requirement to protect material property takes precedence over the physical safety of the occupants in the event of a fire.

Design of internally opening grilles and written duty of advice

When a protected opening must serve as an emergency escape, the locksmith makes and fits an opening security grille. The fixed frame, made of angles or profiled steel tubes, is firmly fixed into the structural work, while the movable leaf pivots on reinforced hinges that cannot be lifted off from the outside. The critical point of the work lies in its locking mechanism, which must combine inviolability from the street with instant operation from the room.

  1. Selecting the keyless locking systemUse a latch bolt or a fire-brigade espagnolette protected by a tamper-proof housing. Unlocking must be achieved by a single simple manual action, such as a bolt under a cover or an operating handle, without handling a key or remembering a code.
  2. Protection against reaching through by handFit a solid sheet-metal deflector or a fine-mesh metal screen around the internal operating device. This shield prevents anyone outside from reaching the lock with a hook or a piece of wire through the bars after breaking the glass.
  3. Checking the direction and angle of openingAdjust the hinges and the stop so as to ensure that the leaf opens by more than ninety degrees outwards or inwards depending on the configuration of the reveal, thereby releasing the whole clear opening required for evacuation.
  4. Functional test under simulated thermal loadCheck that the bolt does not jam at all in the keep. Provide sufficient functional clearance between the fixed frame and the leaf to absorb any expansion without blocking manual opening.

It frequently happens that an owner or building manager demands completely fixed bars for cost reasons, refusing the extra cost of a secure opening fitting. In this situation, the foreman or site manager comes up against the fundamental rules of the contract for work and services under the Code of Obligations (CO). The contractor has a legal obligation to warn the client immediately when the instructions received compromise the compliance or safety of the work.

This warning must take the form of an official written notice, recorded in the site report, sent by registered letter or by email with formal acknowledgement of receipt. The locksmith states in it the exact intended use of the rooms, the risk of persons being trapped in the event of fire and the non-compliance with the cantonal fire protection regulations. If the client maintains the instruction despite the warning, the craftsman incurs joint and several liability if he installs a system that is manifestly dangerous to the physical integrity of the occupants.

Rooms subject to the ban on fixed bars and fallback routes

Fitting fixed bars on a glazed opening creates a point of no return in the event of fire. While the grille prevents night-time intrusion through a basement window or low window, it also traps the occupants as soon as internal circulation routes become impassable because of hot smoke. The locksmith must systematically analyse the function of the rooms before any welded metalwork is manufactured.

Second fallback escape route
Practicable external opening allowing persons to be rescued or to escape when the main staircase or access corridor is saturated with fire or combustion gases.

Under the Swiss fire protection regulations issued by the VKF/AEAI, no fixed grille may block a window recognised as an escape exit or as a rescue access for firefighters. This ban applies first and foremost to habitable rooms in basements, such as bedrooms with English-style sunken areas, hobby workshops with permanent workstations, and ground-level resting rooms without a double exit to the outside. In establishments open to the public, dormitories and early-childhood care facilities, fitting a non-removable guard is strictly prohibited whenever the window forms the second outlet to the open air.

Classification of rooms and compatibility with security grilles
Room useOpening configurationPermitted deviceEvacuation requirement
Cellar / Store with no human presenceConcrete light well or high windowFixed sealed grilleNo evacuation required
Habitable basement bedroomSunken area or open openingGrille opening without a keyIndependent direct exit mandatory
Commercial premises / Production workshopGround-floor window onto the streetHinged opening grilleInternal emergency release within 3 seconds
Medical establishment or dormitoryAll façade openingsOpening grille with interlock, or removedPriority rescue by fire-service ladder

Design of internally opening grilles and written traceability

To reconcile the requirement for mechanical security with that of emergency evacuation, contemporary ironwork uses an opening leaf mounted on protected welded hinges. The assembly consists of a wrought tubular subframe, fixed in the reveal by mechanical anchors protected against unscrewing, and a perforated panel whose locking follows an asymmetrical kinematic.

  1. Fitting a keyless mechanical lockFit a multipoint locking case equipped with a latch bolt or protected espagnolettes. On the inside, the mechanism is operated by a recessed lever handle or a rotating handle protected by a sealed housing, guaranteeing instant operation without searching for a key in the dark.
  2. Protecting the control point against external intrusionPlace a steel shielding plate at least 2 mm thick around the internal control. This plate must extend at least 400 mm on each side of the mechanism to prevent an arm or a hook from passing through the outer bars.
  3. Fitting secure hinges with a stopFix the leaf on hinges with welded pins and axial anti-lift pegs. An opening stop at 90 degrees or 180 degrees holds the grille flat against the masonry so that it does not close again under the effect of a draught during the panic.

The metal construction contractor has a clear duty to warn in the face of contradictory requests from the client's side. When an owner demands the anchoring of a rigid mesh or a non-removable welded grille in front of the openings of a room used for habitation, the locksmith must issue a formal notification. This written document points out the manifest incompatibility between the work ordered and the rules for the safety of persons recommended by the fire protection authority.

This warning must absolutely detail the nature of the risks incurred: occupants trapped in the event of a room fire, impossibility of access for fire hoses via the façade, and the liability of the building operator being engaged. The letter, placed in the work file and sent to the client before manufacture begins, discharges the contractor if he has to refuse to carry out a dangerous device prohibited by the Swiss state of the art.

Disputes and deadlocks: alert procedure and handling the client's refusal

On the construction site, a deadlock frequently arises when the owner demands the welding of a fixed grille on the openings of basement bedrooms or workshops in order to satisfy the requirements of a burglary insurer, even though these openings are the only practicable escape exit. Faced with the VKF/AEAI fire protection regulations, the locksmith is confronted with a direct conflict between the mechanical protection of property and the evacuation of persons. If the client refuses the extra cost of an opening frame fitted with anti-panic locking or an internal espagnolette under a sealed housing, the company must on no account give way verbally.

  1. Written notification of the duty to notifySend a registered letter or a formal notice without delay to the client and to the site management. This document must precisely record the intended use of the room, the danger of asphyxiation or thermal entrapment in the event of fire, and the non-compliance of non-removable bars with the escape routes required.
  2. Proposing a compliant technical variantSubmit an amended quote detailing a frame opening outwards or inwards, hinged on armoured hinges that cannot be lifted off and fitted with direct manual unlocking from the inside without a key, protecting external access by a deflector plate against picking.
  3. Stopping installation or formal refusal to carry out the workIn the event of a persistent written order from the client imposing fixed bars on a glazed opening designated as an emergency exit, the locksmith must record his refusal to carry out the permanent fixing, because endangering the life of others directly engages the liability of the person carrying out the work under criminal law, according to the Code of Obligations (CO) and the Swiss Criminal Code.

Where the work has already been installed and a cantonal fire inspector or a municipal representative orders it to be brought into compliance, the adaptation often requires cutting out the existing anchorages. The locksmith converts the leaf into a pivoting frame by means of a kit of welded hinges on mechanically anchored plates, incorporating an internal lock with a single control. All adaptations and reservations must be recorded in the acceptance report according to standard SIA 118, specifying that the use of internal padlocks remains strictly prohibited, as it would neutralise the evacuation system.

Frequently asked questions

Can an owner demand a completely fixed grille on the window of a habitable basement bedroom?

No. Where a room contains permanent workstations or is used as a sleeping room without direct access to another emergency exit, the fire protection regulations require a practicable escape route to the outside. If the window is the required second escape route, the locksmith must refuse to install fixed bars and must specify a frame that opens from the inside without tools or a key.

How should the internal locking of an opening grille be designed to prevent break-in by picking?

The internal locking must work without a key, generally by an escape espagnolette, a robust bolt or a protected handle. To counter a burglar attempting to operate the keep after breaking the glass, the locksmith incorporates a steel shielding plate at least two millimetres thick masking the mechanism over fifty centimetres, or a sealed cover removable with one hand which triggers a local alarm on opening.

Is the use of a padlock to secure an opening emergency grille permitted on the construction site?

The use of a padlock or a lock with a removable key is strictly prohibited on an opening used for emergency evacuation. In a situation of panic, power failure or dense smoke, searching for a key compromises the occupants' exit within vital time limits. Any emergency unlocking must be achieved by an immediate, intuitive manual operation from the secured interior area.

What approach should be taken when the burglary insurer and the fire authority have contradictory requirements?

The safety of persons always takes precedence over the protection of property. The cantonal fire inspector or the building police authority has overriding authority over the regulations of private insurance companies. The locksmith must have the opening variant formally validated by the local fire authority before manufacture, then send this written proof to the insurer to ensure that the burglary cover is maintained.

Texts and standards cited

  • norme SIA 118General conditions for the execution of construction work and handling of formal notices under the duty of advice

In the same section