Skip to content
Website
🧱 CFC 281Cement or anhydrite screed: selection and executionChapter 5 of 10 in the section

Reinforcing the screed: mesh, fibres, what it prevents and what it does not prevent

This chapter clarifies the actual action of wire mesh and fibres in cement or calcium sulphate screeds. You will learn how to correctly position the reinforcement within the mortar thickness, distinguish the illusory anti-cracking effect from the limitation of height differences, and organise the control joint network in accordance with Swiss codes of practice.

Key takeaways

  • Neither mesh nor fibres prevent cement screeds from cracking due to shrinkage.
  • Microfibres reduce early surface crazing without replacing structural metal reinforcement.
  • The mesh must strictly be located in the upper third to limit differential height differences.
  • Only rigorous control joint layout and correct mix proportions control cracking.

Understanding the mechanical behaviour of reinforcement and fibres

On construction sites in Western Switzerland, a persistent misconception attributes to wire mesh or synthetic fibres the power to eliminate mortar cracking. Materials physics and the SIA 251 standard point to a different reality: no addition of reinforcement eliminates the internal stresses created by hydraulic or thermal shrinkage in a cement screed. During the setting and evaporation of excess mixing water, the cement paste inevitably decreases in volume. If this deformation meets any restraint, the mortar fractures as soon as the tensile stress exceeds its own mechanical strength, which is still very low during the first few days.

Screed reinforcement (according to SIA 251)
A metal or synthetic device incorporated into the mortar cross-section, intended to distribute stresses, keep the lips of any potential crack tightly closed, and limit vertical level differences (height differences), without conferring any load-bearing function to the element.

Polypropylene microfibres act exclusively during the very early age of the mortar, in the hours following screeding and floating. They create a dense three-dimensional network that slows down the rapid sedimentation of aggregates and limits the sudden loss of plastic water under draughts. This mechanism drastically reduces surface crazing and early capillary micro-cracks. Conversely, as soon as the screed begins its structural hardening, the very low modulus of elasticity of these synthetic fibres proves incapable of taking up the longitudinal stresses of overall shrinkage.

Wire mesh made of indented or smooth steel wires fulfils a post-cracking function. When the inevitable crack forms across the entire thickness of the floating slab, the steel takes up the tensile stress to keep both edges together. Its main usefulness lies in mechanical bridging: it prevents horizontal shear and above all vertical displacement (height differences) that would destroy the future tiling under the traffic of rolling loads or users.

Functional comparison of incorporation reinforcements for screeds
Technical parameterMetal reinforcing meshPolypropylene microfibres
Phase of maximum efficiencyAfter hardening (long-term shrinkage)Fresh mortar (first 24 hours)
Action on crazingNone or very slightHighly effective against desiccation
Maintaining flatness (height difference)Ensured by transverse rigidityNon-existent under heavy loading
Replacement of jointsProhibited: does not dispense with any jointProhibited: does not dispense with any joint

Positioning the steel and organising the joints to control cracks

To fulfil its role, the wire mesh must be positioned with precision within the installation cross-section. Reinforcement left lying on the polyethylene film or thermal insulation panels is strictly useless: trapped at the bottom, it undergoes compression during shrinkage bending and even accelerates edge spalling. The SIA 251 standard specifies that the reinforcement must be located in the upper third of the screed, embedded in at least fifteen to twenty millimetres of compacted mortar.

Since reinforcement does not prevent shrinkage, the only effective method to prevent random cracking consists of planning shrinkage by guiding fractures. This is achieved through a methodical network of control joints cut with a trowel into the fresh mortar or sawn with a diamond disc to a depth corresponding to one-third of the screed thickness. The layout follows compact geometric figures without acute re-entrant corners.

  • Divide unheated cement screeds into regular bays respecting the slenderness limits of the SIA 251 standard.
  • Mandatorily treat every external corner or room geometry change with a joint to avoid gull-wing corner cracks.
  • Interrupt the wire mesh at control joints to allow the controlled opening of the sawn cut.
  • Install smooth sleeves or metal dowels only if vertical load transfer without horizontal restraint is specified.

Behaviour under thermal loading and actual limits of reinforcement

On construction sites in Western Switzerland, the temptation persists to demand metal reinforcement or synthetic fibres under the pretext of "guaranteeing a crack-free screed". This expectation is based on a fundamental physical confusion. No addition of steel or polypropylene eliminates the hydraulic shrinkage of a cement mortar or the thermal expansion imposed by underfloor heating pipes. When residual water evaporates and the binder hydrates, the matrix decreases in volume. If this contraction is restrained by skirtings, re-entrant corners or door thresholds, the mortar goes into tension. The flexural tensile strength of fresh mortar remains low: as soon as the stress exceeds this capacity, the screed fractures.

The SIA 251 standard highlights the determining principle: the wire mesh does not prevent the appearance of the crack, it limits its opening. Its action begins after the microscopic rupture of the cement matrix. The steel takes up the tensile stress transmitted by bond, preventing the two lips from moving apart in an uncontrolled manner and preventing the vertical displacement of adjacent panels. Without reinforcement or joints, the crack opens widely and propagates. With correctly placed mesh, the deformation is distributed, avoiding height differences that would shear bonded floor finishes subsequently applied.

Technical comparison of the action of reinforcements and fibres according to the SIA 251 standard
Reinforcement deviceActual effect observed during executionProven mechanical inabilityRequired position on site
Welded wire mesh (fine wires)Stitching of shrinkage cracks, limiting lip separation, maintaining altimetryPrevents neither initial cracking nor shear stresses at re-entrant cornersLower third to mid-thickness of the screed, on stable spacers and tied with wire
Synthetic microfibres (polypropylene)Reduction of plastic bleeding micro-cracks during the first hours of settingNo structural load bearing, ineffective against long-term hydraulic shrinkageComplete homogeneous distribution in the mix from batching plant or mixer-transporter
Structural macro-fibres (synthetic or steel)Improvement of post-cracking ductility, partial resistance to residual loadsDoes not exempt from control joint layout or expansion jointsFull multidirectional distribution, increased monitoring of mortar workability

What technically prevents the disorderly opening of cracks

To control the cracking of a floating screed, the determining measures lie in the mortar composition, the floor geometry and the joint treatment, rather than in the reinforcement alone. In a cement screed, shrinkage is directly proportional to the water content. Excess mixing water to facilitate pump placement increases the volume of porous capillary paste and multiplies linear shrinkage. The use of water-reducing plasticising admixtures and strict control of the water/cement ratio constitute the first barrier against excessive shrinkage.

The organisation of control joints dictates the behaviour of the structure. The SIA 251 standard regulates the fragmentation of large surfaces to relieve internal stresses before they reach the rupture threshold of the mortar. These sawn or profiled joints create a weakened section where the shrinkage crack occurs in a straight and controlled manner, instead of wandering in the middle of a room. On underfloor heating, joint layout must systematically respect the distinct heating zones managed by the heating installer trade, in order to prevent differential movements between circuits.

  1. Geometric joint layoutCut the surface into regular panels. Avoid length-to-width ratios greater than 2 to 1, and decouple projections, pillars and narrow corridors using flexible profiles.
  2. Sawing depthMake the saw cut between one-third and half the thickness of the cement screed as soon as the mortar has acquired sufficient hardness not to fray, taking care not to damage the heating pipes.
  3. Protection against early evaporationApply curing using a sealed polyethylene membrane or approved curing compound as soon as smoothing is completed, in order to block surface desiccation due to draughts or direct solar radiation.
  4. Bridging or load transferAt sawn control joints crossed by light traffic, insert smooth metal dowels sheathed on one half to maintain vertical alignment without blocking horizontal shrinkage.

Management of cracking defects and remediation on site

When a secondary crack crosses the screed despite the presence of wire mesh or synthetic microfibres, a methodical analysis is required before any approval for floor finish installation. Neither reinforcing steel nor polypropylene fibres eliminate the natural hydraulic shrinkage of a cement binder: they act solely to distribute mechanical tensions or prevent vertical height differences between neighbouring panels. If the essential layout of control joints has been omitted at door openings, re-entrant corners or spans exceeding recommendations, the screed spontaneously generates its own joint in the form of an uncontrolled fracture. The screed layer must then establish a joint inspection record, check the integrity of the underfloor heating pipe embedment, and refuse any premature bridging.

The most severe defect generally stems from reinforcement poorly positioned at the bottom of the screed. Wire mesh simply laid on the insulation or polyethylene film receives no regulatory cover: it rusts or remains inert under bending stresses. In the event of differential deformation or the passage of a point rolling load, the lips of the fracture shift irremediably in height.

  1. Diagnosis and dimensional stabilisationWait for the complete completion of the official heating protocol and the hygrometric stabilisation of the slab according to the SIA 251 standard. Working on a crack that is still moving or undergoing desiccation causes immediate reopening along the bonding line.
  2. Chasing and mechanical groovesOpen the crack with an angle grinder fitted with a diamond disc over at least one-third of the screed height. Make transverse perpendicular grooves fifteen centimetres long every twenty centimetres to accommodate staples.
  3. Stapling and epoxy keyingEmbed flat steel corrugated staples into each transverse groove. Fill the cavities with a low-viscosity two-component epoxy resin to refusal, then immediately broadcast dry quartz to refusal to create a rough bonding key.
Typology of defects related to reinforcement and corrective measures
Observed defectExecution causeScreed layer technical repair
Straight through-crackShrinkage joint omitted at re-entrant cornerRigid bridging using staples and epoxy resin
Height difference at the lipsMesh laid at the bottom without spacersGrinding down the step and mechanical stitching
Diffuse surface crazingRapid desiccation or excessively wet mixDiamond grinding and primer

Frequently asked questions

Why does a cement screed crack despite the presence of wire mesh?

The reinforcing mesh does not modify the intrinsic hydraulic shrinkage tensions of cement during its hardening. Its steel only comes into action once the matrix is ruptured by tension. Without regular control joints complying with the SIA 251 standard, the accumulated linear shrinkage exceeds the mechanical strength of the fresh mortar: the screed inevitably breaks, with the mesh merely keeping the two edges together to prevent them from moving apart.

Do polypropylene microfibres make it possible to eliminate metal reinforcement?

No, short synthetic fibres and wire mesh fulfil two distinct functions. Microfibres only counteract early cracking due to the rapid evaporation of water during the first hours after screeding. Conversely, they exhibit no post-cracking resistance under service loads. If the design requires mechanical maintenance of the lips or restoration of flatness, the mesh remains essential, wedged in the lower third.

At what precise height should the mesh be positioned within the thickness of the screed?

In a floating screed on thermal or acoustic insulation, the wire mesh must be placed strictly in the lower third of the total thickness, without ever resting on the decoupling film. Appropriate synthetic spacers must guarantee a minimum cover of fifteen millimetres of mortar under the bars. Mesh pressed against the ground proves totally useless, while mesh positioned too high risks surfacing during trowelling and damaging future finishes.

How to treat a crack that has appeared before the initial heating phase?

A crack on a cement screed must never be filled before carrying out the complete heating cycle. The thermal rise generates expansions followed by additional shrinkages that would instantly fracture a premature repair. Once the thermal protocol is completed and the return to ambient temperature is validated, the screed layer bridges the stabilised crack using transverse grooves, installation of corrugated metal staples, and injection of a two-component epoxy resin saturated with quartz sand.

Texts and standards cited

  • SIA 251Screeds in construction

In the same section