Skip to content
Website
🧱 CFC 281Movement joints and layoutChapter 9 of 10 in the section

Industrial floor: rolling load, surface hardener, armored joints and wear

This chapter guides you through the execution of screeds subject to heavy mechanical stress in accordance with standard SIA 251. You will learn how to size the incorporation of mineral surface hardeners to withstand dynamic indentation from handling equipment. You will also learn how to install robust metal armored joints to eliminate the systematic spalling caused by hard pallet truck wheels at the dividing edges.

Key takeaways

  • Hard pallet truck wheels rapidly destroy the sharp edges of unprotected dividing joints.
  • Standard SIA 251 governs the mechanical strength classes required for heavily stressed industrial floors.
  • Quartz- or corundum-based surface hardeners significantly improve indentation resistance.
  • Anchored metal profiles guarantee rolling continuity without degrading joint lips.

Concentrated rolling load and edge protection by metal profiles

In a logistics hall or a craft workshop, the most destructive stresses for a screed do not come from distributed static loads, but from the traffic of handling equipment. Manual or electric pallet trucks fitted with rigid rollers made of polyamide or hard polyurethane apply an extremely small impact surface. This concentration of forces generates considerable local contact pressures, combined with repeated dynamic shocks during acceleration, braking and changes of direction.

A dividing joint that is simply sawn or filled with a flexible plastic profile cannot withstand this operating regime. When the roller crosses the joint opening, it leaves the plane of one slab to strike the opposite edge violently. Without armor, the screed mortar undergoes rapid spalling: the lips chip, the opening widens and the joint turns into a rut that destroys the tires of the trucks and compromises personnel safety.

To ensure the durability of the structure in accordance with the requirements of standard SIA 251, the use of metal profiles for armored joints is mandatory in all heavy traffic corridors. These prefabricated systems consist of two drawn steel flats or angles, temporarily connected by shear screws during casting, and provided with continuous or sinusoidal anchoring legs that are embedded in the mass of the mortar. They incorporate flat dowels ensuring vertical load transfer between panels while allowing free horizontal shrinkage.

Behavior of joint types under handling equipment loads
Joint typeHard wheel capacityEdge resistanceIntended use
Unarmored saw cutZero: degradation within a few weeksContinuous spalling under impactPedestrian technical rooms without pallet trucks
Standard synthetic profileLow: indentation of the plasticTearing of lips under loadLight traffic on pneumatic tires
Prefabricated steel armored jointExcellent: continuous load transferTotal metal protection of anglesStorage halls and dense traffic lanes

Incorporation of the mineral hardener and requirements of standard SIA 251

The strength of an industrial floor screed does not depend solely on its joint reinforcement: it relies on the hardness of its first surface millimeters. Standard SIA 251 defines the compressive strength, flexural tensile strength and abrasion resistance criteria required to support intensive rolling. A traditional mortar, even richly dosed with cement, presents a surface paste that is too vulnerable to delamination and dusting under shear stresses.

To achieve the most severe wear classes, the screed layer applies a mineral surface hardener. This calibrated dry mix consists of special cements, water-reducing admixtures and very hard aggregates, mainly selected quartz or synthetic emery and corundum aggregates. The system is incorporated fresh-on-fresh directly onto the screed struck off with a screed board, creating an inseparable monolithic bond with the body of the slab.

  1. Levelling and opening power trowellingLevel the screed using a vibrating screed board. As soon as setting begins, open the surface laitance with a power trowel fitted with a smoothing disc.
  2. Regular aggregate spreadingManually or using a spreader trolley, sprinkle the hard aggregate mixture observing the prescribed dosage, generally spread in two crossed passes.
  3. Moistening and mechanical compactionWait for the powder to absorb the free moisture of the mortar, then run the ride-on trowel to drive the hard grains into the cement matrix.
  4. Gradual power trowel smoothingReplace the disc with finishing steel blades. Carry out several passes by gradually increasing the angle of the blades until a closed and shiny surface finish is obtained.
  5. Application of curing compoundSpray an approved protective curing agent immediately after the final pass to prevent rapid desiccation and premature cracking.

Dynamic keying and load transmission at armored joints

Under the repeated passage of polyamide or hard polyurethane tires of a pallet truck, the weak point of an industrial slab or wear screed systematically lies in the discontinuity of the joint. When the wheel crosses the joint lip, the vertical shear force applies in an almost point-like manner on a free edge if the system provides no mechanical connection. Without a force transmission device, the upstream slab flexes alone under the peak load, creating an immediate millimeter step against which the roller strikes. This hammering degrades the cement matrix and destroys the edges within a few weeks of intensive operation.

Sinusoidal profile armored joint or anchored angles
Prefabricated metal device sealed into the body of the screed during casting, consisting of flat or sinusoidal steel edges and sliding dowels or transfer plates. It ensures the continuity of the rolling plane and transmits vertical shear forces from one panel to the other without blocking horizontal shrinkage.

Standard SIA 251 governs dimensional requirements and allowable mechanical stresses for screeds subjected to heavy operating loads. To avoid shear failure under heavy rolling loads, the use of flat or trapezoidal dowels coated with synthetic sleeves is required within the thickness of the screed. The layout must rigorously align these profiles with the traffic lanes planned by the operator, avoiding acute-angle intersections that generate parasitic corner cracks.

Comparative behavior of joint types under hard-wheeled vehicle traffic
Joint typeBehavior under heavy rolling loadRisk of lip degradationRecommended operating destination
Unarmored sawn joint filled with sealantLow: differential settlement under the wheelVery high: rapid spalling and tearing of the sealantPedestrian traffic or soft pneumatic tire trucks only
Joint with straight metal anglesGood: direct mechanical protection of the edgeMedium: repeated shock during perpendicular wheel passageModerate transverse traffic lanes or oblique crossing
Wavy sinusoidal profile armored jointOptimal: permanent and transition-free support of the rollerZero: elimination of vertical impact by continuous geometryHigh-frequency logistics corridors and manual pallet truck areas

Execution of the hardener and control of mechanical surface finishing

The incorporation of a mineral or metallic surface hardener tolerates no approximation of timing. The application of the dry mix based on corundum, quartz or steel particles must take place at the precise moment when the screed mortar has made its initial set without losing its interstitial water. Premature dusting on liquid bleed water causes subsequent delamination of the wear layer due to excess water beneath the hardened paste. Conversely, late incorporation prevents mechanical bonding within the cement matrix, which leads to flaking under the dynamic indentation of trucks.

  1. First dusting and spontaneous wettingManually or using a regulated spreader trolley, spread approximately sixty percent of the mineral aggregate load on the surface struck off with the rule as soon as an operator's footprint leaves only a three-millimeter indentation. Wait for natural humidification by capillarity without adding mixing water.
  2. First mechanical power trowellingRun the rotary power trowel equipped with its surface-finishing pan at low speed to incorporate the first pass into the upper laitance of the screed.
  3. Second addition and cross passesSpread the balance of the hardener perpendicularly to the direction of the first pass, then carry out mechanical compaction to homogenize the quartz or corundum content over the entire wear thickness.
  4. Finishing smoothing with inclined bladesReplace the pan with finishing blades and gradually increase the speed and inclination angle of the blades. The operation compacts the upper edge and closes surface porosity until a polished and dense appearance is obtained.

The sawing of shrinkage joints must be carried out as soon as the hardener resists tearing under the diamond blade, generally between twelve and twenty-four hours after surface finishing depending on the ambient temperature of the building. The depth of the saw cut must reach at least one-third of the total thickness of the screed in accordance with the requirements of standard SIA 251. Any delay in this operation induces a random crack initiation off-track, particularly around the metal baseplates of through armored joints.

Joint and surface pathologies under rolling load: diagnosis and repairs

Under the repeated action of hard polyamide or polyurethane wheels of pallet trucks, execution flaws manifest rapidly. Shear stress and dynamic indentation pulverize the lips of an unprotected saw cut within a few weeks of intensive traffic. The appearance of an altimetric offset between two screed panels indicates a load transfer defect or crushing of the sub-layer. If the surface hardener flakes off in patches, the diagnosis reveals dusting that was too late on an already closed mortar, preventing the monolithic setting required by standard SIA 251.

  1. Chipping out and reconstruction of joint lipsDelaminated or spalled parts are chipped out using a light hammer down to sound screed concrete. After industrial vacuum cleaning, the edges are reconstructed using an epoxy resin mortar with high mechanical compactness, poured behind temporary metal formwork ensuring perfect flatness of the rolling plane.
  2. Repair of unseated metal profilesAn armored joint whose anchoring legs are torn out must be entirely sawn and extracted. The groove is recut to a sufficient width to seal a replacement profile with reinforced anchors, chemically anchored into the body of the screed, with laser alignment to eliminate any step.
  3. Dynamic panel stabilizationIn the event of vertical bouncing during vehicle passage, stainless steel load transfer dowels are inserted by horizontal coring or sawing of grooves perpendicular to the joint line, before pressure resin injection to block rocking without hindering axial shrinkage.

Frequently asked questions

Why does a classic sawn dividing joint get destroyed under a pallet truck?

Small-diameter metal or nylon rollers exert very high point pressure. When the wheel crosses the void of the saw cut, the dynamic shock applies directly to the unprotected sharp angle of the screed lip. Without an armor angle or integrated surface hardener, the mortar spalls under shear stress, creating a step that accelerates the ruin of the traffic area.

How does standard SIA 251 regulate the use of industrial screeds?

Standard SIA 251 defines the mechanical performance requirements relating to screeds, notably compressive, flexural and surface wear resistance. It requires verifying the adequacy between screed thickness, substrate strength and actual operating loads, imposing specific construction provisions, such as edge reinforcement and the incorporation of hard aggregates when heavy rolling loads are expected.

When should the surface hardener be incorporated into the fresh screed?

Incorporation by dusting is carried out as soon as the operator leaves a footprint of about 3 to 5 millimeters in the trowelled screed. The mineral mixture must draw bleed water to hydrate properly. Early spreading drowns the grains in the laitance, whereas too late an application prevents mechanical bonding with the underlying mortar, causing detachment of the wear layer under subsequent rolling.

What precautions should be taken for levelling a metal armored joint?

Flat irons or angles must be set with zero altimetric tolerance relative to the finished level of the screed. Power trowelling and ride-on smoothing must flush rigorously with the metal edge without creating hollows or overthicknesses. Any level deviation constitutes an impact obstacle for hard wheels, generating intense vibrations that eventually break the anchoring legs in the screed.

Texts and standards cited

  • SIA 251Floating screeds, bonded screeds and wear layers: design, mechanical requirements and execution.

In the same section