Skip to content
Website
🧱 CFC 281Movement joints and layoutChapter 7 of 10 in the section

A crack appears: active or stabilised, stitching, resin and when it is too late

On the construction site, the appearance of a crack in the screed requires a rapid diagnosis before laying finishes. This guide details the methods for distinguishing a stabilised crack from an active crack linked to thermal variations or shrinkage. You will learn how to execute a mechanical bridging using staples and resin, or how to transform the opening into a proper movement joint.

Key takeaways

  • The SIA 251 standard governs the condition of the substrate prior to acceptance by subsequent trades.
  • A stabilised crack is rigidly bridged using transverse slots, corrugated ties and resin grout.
  • Any active crack that continues to move under thermal cycling must be converted into a control joint.
  • Bridging a crack that is still moving inevitably causes the underlying tiling to crack.

Qualifying the defect: distinguishing a dead crack from a live crack

As soon as a break appears on the surface of a fluid or traditional screed, the first reaction is to determine its physical origin. According to professional rules and the SIA 251 standard, a crack may result from early hydraulic shrinkage, a change in thickness when crossing a threshold, or repeated thermal movement. Repairing without qualifying the phenomenon leads to immediate recurrence or shearing of the floor finishes.

Criteria for distinguishing between a stabilised break and active movement
Analysis criterionStabilised (dead) crackActive (live) crack
Evolution of the openingConstant width measured with a crack monitorDimensional variation according to temperature
Phase of appearanceFirst month of curing and initial dryingDuring or after the gradual heating-up phase
Geometric traceFollows plastic shrinkage, often erraticStraight along a hard point or constriction
Recommended treatmentRigid stitching using staples and cast resinFlexible treatment or creation of a clean joint

To confirm that a crack is stabilised, the screed layer places pure plaster tell-tales or a graduated crack monitor accurate to a tenth of a millimetre. Observation is carried out over a complete heating cycle or for a minimum period of ten working days. If the tell-tale breaks or if the cursor oscillates with the temperature of the heat-transfer fluid, the crack is active: the screed element is working mechanically and will not tolerate any rigid bonding.

Repair methodology: structural stitching or conversion into a joint

When diagnosis confirms that the crack is no longer moving, the monolith is restored by injection and transverse anchorage. This process re-establishes the transfer of vertical loads on either side of the fracture edges, preventing the step-up effect under construction traffic or future operation of the premises.

  1. Opening the crack and saw cutsOpen the slit with a diamond disc to one-third of the screed thickness. Make perpendicular slots approximately 150 millimetres long, spaced 200 to 300 millimetres apart.
  2. Industrial dust removalCarefully vacuum each cut using a high-suction industrial vacuum cleaner equipped with a fine-dust filter. No mineral residue must hinder chemical bonding.
  3. Insertion of metal staplesPlace corrugated flat steel ties or zinc-coated anchorage staples at the bottom of the transverse slots, at mid-depth of the prepared groove.
  4. Resin pouring and sandingFill the slits and slots to refusal with a fluid epoxy resin or a two-component silicate binder. Immediately sand to refusal with dried quartz to ensure subsequent mechanical bonding.

If the defect is classified as active, the SIA 251 standard prohibits rigid blocking. The crack must be treated as a spontaneous control joint created by the internal forces of the screed. The screed layer then retraces the line using a disc cutter to a minimum depth of half the mortar thickness, without ever hitting the underlying technical ducts or pipes.

Once the edge has been straightened and cleaned along its entire path, the resulting void is fitted with a closed-cell polyethylene foam backing cord. The slit thus remains free for its expansion or shrinkage movements. The construction site report precisely records the location of this new cut so that the flooring installer can lay out their own joint in exact correspondence.

Execution protocol: stitching a stabilised crack or creating a clean joint

Working on a cracked screed cannot be improvised with a cartridge gun. Once the absence of kinematic movement has been verified, the mechanical consolidation of a stabilised crack requires rigid bridging capable of restoring the monolithism of the fluid or traditional screed. The standardised process according to the SIA 251 standard relies on metal stitching combined with the pouring of reactive resin under low pressure or by gravity.

  1. Open and cut perpendicular slotsOpen the crack line with an angle grinder equipped with a diamond disc to one-third of the screed thickness, without ever hitting the underfloor heating pipes. Make perpendicular transverse slots 100 to 150 mm long, spaced 200 to 300 mm from axis to axis, excavated to a minimum depth of 15 to 20 mm.
  2. Vacuum dust using an industrial vacuum cleanerThoroughly vacuum the slits and slots using an industrial-grade site vacuum cleaner. The total absence of powdery laitance and loose particles guarantees the mechanical adhesion of the chemical binder to the cementitious walls.
  3. Insert metal connectorsPlace a flat corrugated steel staple or a notched reinforcement dowel 5 to 6 mm in diameter into each transverse notch. These reinforcements take up the shear forces and prevent lateral sliding of the edges.
  4. Inject the sealing binder and sandFill the slots and the crack to refusal with a fluid two-component epoxy resin or a solvent-free polyurethane reaction resin. Immediately sprinkle the still-tacky surface with dry quartz sand with a grain size of 0.4 to 0.8 mm to create the roughness required for subsequent installation mortars.

Conversely, if thermal or structural kinematics require the active crack to be transformed into a control joint, the screed craftsman abandons stitching. The crack is rectified with a diamond disc along as straight a line as possible to remove ragged edges. A compressible strip or closed-cell polyethylene foam backing cord is inserted into the slot to define the sealing base and prevent three-sided adhesion. Caulking is then provided by a flexible elastomeric sealant compatible with the predictable deformations of the assembly.

Points of no return: limits of reparability and demolition criteria

Filling or cutting control joints are not universal remedies. When faced with major defects observed prior to handover, the SIA 251 standard sets strict geometric and mechanical requirements. When the integrity of the floating screed is broken across its entire thickness with a loss of support on the acoustic or thermal insulation, resin bridging can no longer support service loads.

Decision-making aid based on defect morphology and dynamics
Type of defectObserved originKinematic diagnosisPrescribed technical action
Dry linear crack less than 1 mmCompleted hydraulic shrinkageStabilised (dead)Steel stitching and injection of sanded epoxy resin.
Crack around internal cornersAbsence of control joint cutActive (thermal)Transformation into a clean joint with elastomeric sealant.
Displacement greater than 2 mm with step effectSettlement or crushing of the underlying insulationIrreversible / BrokenLocal demolition of the span and complete reconstruction.
Tight honeycombed crazing and powdery laitanceAbrupt surface desiccationSuperficial non-load-bearingSurface planing or specific smoothing compound after sanding.
Corner rocking with generalised hollow soundSevere thermal curlingActive / DebondedComplete removal of the affected screed slab.

The most critical case remains the vertical level difference between the edges of the fracture. A sagging edge of more than 1.5 mm indicates that the resilient underlay has collapsed under weight or that the screed has fractured by bending under point load. Injecting resin into a unbonded base is like masking a void: when a pallet truck or heavy furniture passes over, the shear stress breaks the resin bead or fractures the adjacent mortar.

When crazing indicates an overall loss of strength in the mix following overdosing with water or a destructive draught during setting, the surface cohesion no longer meets the required tolerances. The contractor then applies the rules for notifying defects provided for by contract law: complete removal by demolition and re-pouring of the defective span is mandatory before any authorisation to lay soft or bonded flooring.

Dispute management and treatment failures: arbitration between stitching and joint conversion

When the initial evaluation of a crack proves to be incorrect, the construction site enters a critical situation. The most frequent case remains the rigid epoxy resin stitching of a crack falsely classified as stabilised. If the slit was actually active, subjected to the thermal expansion cycles of the floor heating or structural movements, the accumulated mechanical stress systematically causes a fracture to appear parallel a few centimetres from the metal pins. This reopening demonstrates the failure of rigid bridging and requires the immediate abandonment of any further stitching attempts.

In the event of a technical dispute regarding the active or stabilised nature of the crack, the installation of a millimetric tell-tale or a deformable gauge is the only admissible evidentiary procedure. During a complete heating and cooling cycle, the opening variation is recorded jointly with site management. Any measurable movement greater than a tenth of a millimetre definitively disqualifies structural bonding and validates conversion into a clean control joint, equipped with a compressible backing cord and an elastomeric sealant.

If the defect is accompanied by a permanent horizontal displacement or debonding at the acoustic insulation, local repair is no longer sufficient. The joint inspection report draws up the inventory of fixtures according to the SIA 118 standard and defines the partial demolition zone. Cutting is then carried out down to the load-bearing substrate while scrupulously preserving the heating pipes, before reconstructing an unbonded panel in accordance with the requirements of the SIA 251 standard.

Frequently asked questions

Can a crack that has reappeared next to stitching be bridged a second time?

No. The reappearance of a crack along a stitching line proves unequivocally that the original discontinuity was an active crack subject to thermal or dynamic expansions. Repeating resin stitching would only move the fracture line a few centimetres further. The area must be sawed to permanently transform the crack into a clean control joint, filled with a backing cord and a flexible elastomeric sealant.

Who approves the transformation of a crack into a joint if the tiler refuses it?

The final decision rests with site management after written notification by the screed layer. An active crack cannot be bonded without causing the overlying tiling to break. The screed layer points out the moving nature of the slit in accordance with the SIA 251 standard. The architect and the flooring installer must adapt the layout to relocate this control joint into the finishing coating, thus avoiding a shear failure.

How long must a gauge be observed to certify that a crack is stabilised?

Observation must cover at least one complete thermal cycle of the underfloor heating, i.e., maximum temperature rise, the holding period, and complete return to ambient temperature, over a period of seven to ten days. On an unheated screed, a minimum period of fourteen days of exposure to ambient thermal and hygrometric variations of the construction site is required to record any opening variation on the measurement tell-tale.

What should be done if the underfloor heating pipes are too close to cut the crack?

If the pipe layout prevents transverse grooving without risk of perforation, mechanical stitching is excluded. Treatment is limited to a superficial opening of the crack line with a manual chisel, followed by gravity pouring of a low-viscosity fluid epoxy resin. If the crack is active, a surface uncoupling joint must be arranged without cutting into the depth embedding the heating ducts.

Texts and standards cited

  • SIA 251Floating screeds, base slabs and fluid floor coverings: design, execution and requirements relating to joints
  • SIA 118General conditions for the execution of construction work: notice of defects and joint inspections

In the same section