Skip to content
Website
🧱 CFC 281Substrate, underlays and decouplingChapter 5 of 10 in the section

Pipes on the slab: concrete cover, thickness above and crossings that are too high

This chapter teaches you how to locate high points formed by the crossing of service ducts on the raw slab. You will learn how to measure the available height below the level mark, assess the risk of cracking in the floating screed and specify the execution of a levelling layer in compliance with Swiss professional rules.

Key takeaways

  • Sanitary and electrical duct crossings create critical high points on the raw slab.
  • Standard SIA 251 requires a minimum and constant cover thickness over the entire surface.
  • Installing insulation directly over a bundle of pipes creates unacceptable void areas.
  • The lean mortar levelling layer compensates for the pipework and restores a stable, flat bearing surface.

Locating pipe stacks and checking the under-screed clearance

The screed layer's work systematically begins with the visual and geometrical acceptance of the raw load-bearing slab. On residential and commercial construction sites, plumbing, electrical and heating installers fix their conduits to the floor. When these ducts cross in the same location, the cumulative thickness frequently reaches five to eight centimetres. These crossings create localised bumps that drastically reduce the clearance allowance provided for the acoustic underlay and the liquid or traditional screed.

Pipe high point
The top of a pipe or a bundle of superimposed service ducts projecting above the expected seating level for thermal or acoustic insulation layers.

The team leader checks the altimetry upon arrival using a laser level set to the one-metre level mark transferred onto the concrete walls. Direct measurement between the top of the highest pipe and the planned finished floor level determines the residual space. In accordance with the requirements of standard SIA 251, the screed thickness above the pipe or insulation must scrupulously comply with the nominal design values to guarantee mechanical resistance under operational loads.

Checking allowance heights according to the type of network encountered
Type of network on slabTypical bundle heightConsequence for the screedRequired corrective measure
Single contiguous electrical ducts20 to 25 mmDirect insulation installation possible with packingCheck local flatness
Sanitary pipe with insulating sleeve40 to 60 mmLoss of clearance for thermal insulationLevelling screed mandatory
Sanitary pipe and electrical duct crossing70 to 95 mmResidual screed thickness below thresholdGeneral levelling or network rerouting
Gravity drainage with slope50 to 110 mmLocalised high point blocking insulation installationRaising finished level or lost formwork

Specify and pour a levelling layer to embed the networks

When the presence of service networks on the floor prevents the flat and continuous installation of insulating underlays, the execution of a levelling layer is required. This process involves pouring a lean mortar or fluid lightweight concrete directly onto the load-bearing slab in order to encase all conduits. This levelling form restores a horizontal, rigid and clean seating surface, perfectly suited to receive the specified acoustic or thermal insulation assembly.

Pipework and conduits laid on the load-bearing support must be embedded in a continuous leveling layer to form a rigid and flat support before installing the insulation underlays.

Norme SIA 251
  1. Cleaning and fixing networksCheck that the slab has been swept and ensure that the installers have solidly anchored the ducts every metre to prevent them from lifting during pouring.
  2. Transferring pouring levelsSet the laser screed guides so that they exceed the top of the highest pipe by at least ten millimetres across the entire room.
  3. Implementation of levelling mortarPump a low-shrinkage mortar or a lightweight compound to fill all gaps between ducts without leaving open cavities.
  4. Trowelling and dryingScreed the surface with a straightedge to obtain compliant flatness before authorising the jointed installation of thermal or acoustic insulation boards.

Execution of the levelling layer: stable embedding and neutralisation of crossings

When plumbing, electrical and ventilation installations create duct stacks on the raw slab, the direct installation of insulation boards becomes technically impossible. The overhang would break the insulation under load and create unacceptable air voids for acoustics. The levelling layer is then used to embed all networks under a flat, continuous and stable surface. This embedding mortar has no mechanical load-bearing function for the building, but it guarantees a deformation-resistant seating designed to receive the resilient or thermal underlays of the floating assembly.

On construction sites, traditional lean mortar batched with hydraulic binder or lightweight concretes based on polystyrene aggregates or expanded clay beads are the usual solutions. The choice depends on the available height allowance and the allowable load on the slab. The embedding material must be screeded using level markers rigorously set to the most critical high point of the service network. No pipe or connection sleeve must protrude from the finished level of the levelling layer. A flush duct forms a hard edge that would puncture the insulation boards installed subsequently.

  1. Checking pipe bundle fixingsCheck that each pipe bundle is securely tied to the slab before injecting or pouring the levelling layer. Polyethylene pipes or empty electrical ducts tend to float under the thrust of a liquid lightweight mortar if they are not restrained by strapping every metre.
  2. Pouring and setting at the highest upper edge levelScreed the compensation layer while ensuring minimum clearance above the thickest crossing. The mixture must penetrate under the pipes without leaving hollow cavities along tight bundles.
  3. Flatness check and setting timeCheck general flatness with a 2-metre straightedge. Comply with the hardening time specific to the levelling mortar before authorising personnel traffic and the installation of insulation underlays.

Restoration of useful clearance and tolerances in accordance with standard SIA 251

Standard SIA 251 sets strict requirements concerning the minimum thickness of the floating screed, which must be calculated exclusively from the upper face of the insulation board laid on a flat support. If duct crossings have not been treated with a generalised levelling layer, the temptation to locally thin the screed above a high point inevitably leads to failure. A cement or calcium sulphate screed whose useful thickness is reduced by half at a service bundle will crack as soon as loads are applied or during initial heating-up.

When the levelling layer has restored a clean zero level above the pipework, the design thickness of the screed can be respected across the entire room. This dimensional regularity ensures homogeneous rigidity against dynamic loads and guarantees symmetrical thermal behaviour if underfloor heating coils are subsequently installed above the insulation. The following table summarises the typical configurations encountered in technical level renovations.

Management of allowance heights according to the pipe integration method
Network configurationTreatment on the raw slabImpact on insulationResidual screed thickness
Single pipes laid flat without crossingDirect installation between cut insulation boardsCareful cuts, residual thermal bridgesNominal thickness preserved according to standard SIA 251
Crossing of two pipes (plumbing and electricity)Partial levelling or lean mortar compensationContinuous flat seating without punchingNominal thickness guaranteed across the entire room
Three pipes superimposed at the same pointMandatory general levelling across the entire floorInsulation laid flat over the full surfaceNominal thickness respected, floor level raised
Unlevelled high point (screed poured as direct cover)Lack of decoupling and discontinuous installationCrushed insulation, cracking at the crossingCritical under-thickness, guaranteed mechanical failure

Underlays and insulation layers must provide continuous support on a flat and stable substrate. The nominal thickness of the floating screed must under no circumstances be compromised by the presence of penetrating technical elements.

Norme SIA 251

Allowance conflict management and site arbitration

When uncoordinated superposition of electrical ducts and plumbing pipes forms a high point, the residual screed thickness frequently falls below the requirements of standard SIA 251. Pouring under these conditions exposes the work to immediate failure: the floating screed loses its mechanical inertia at the node, differential settlement shears the material and the floor covering suffers through-cracking from the very first site loads. No screed layer should agree to pour a tapered thickness over an un-encased bundle of pipes.

  1. Contradictory altimetric surveyMeasure the distance between the upper edge of the highest pipe and the metric level mark drawn by the structural work using a laser tape measure. Record the thickness deficit in relation to the finished floor assembly provided in the specification, then forward the findings to site management.
  2. Layout revision by installersCall upon the plumbing or electrical trades to uncross the ducts. Moving a heating pipe or rerouting a plumbing pipe into a clearance area very often eliminates the crossing without impacting the load-bearing structure.
  3. Execution of an embedding levelling layerIf the pipes cannot be moved, execute a levelling layer in lean mortar or lightweight concrete over the entire room. This layer embeds the networks and reconstitutes a flat, continuous and deformation-resistant support surface to receive the thermal or acoustic insulation.
  4. Requallification of screed mortarWhen the levelling layer drastically reduces the available allowance, site management must validate the transition from a traditional cement screed to a self-levelling fluid screed or one modified with admixtures, tolerating a reduced nominal thickness above the insulating layers in accordance with standard SIA 251.

Any attempt at empirical on-site catching up, such as spot filling with fresh mortar without a suitable binder or mechanical crushing of ducts, will result in the rejection of the work acceptance. Methodical straightening of the substrate before installing insulation boards remains the sole guarantor of the durability of the floating screed.

Frequently asked questions

Can acoustic insulation be installed directly over crossed pipes without a levelling layer?

No, this type of installation must be ruled out. Installing a resilient layer over protruding networks creates voids beneath the insulation. Under the load of liquid or traditional screed and operational traffic, the board sags, which deteriorates acoustic insulation and induces a high risk of screed failure. A levelling layer allows the pipework to be embedded to provide a flat, stable and continuous bearing surface for the insulating underlays.

What is the minimum screed thickness to be respected above the highest point of a duct?

According to standard SIA 251, the nominal thickness of a floating cement screed must not drop below the values defined by the stress class, generally 45 to 65 millimetres above the insulation. If a pipe emerges from the levelling layer, the residual cover clearance becomes insufficient. In this case, a screed poured directly risks cracking due to lack of thickness. A compensation levelling layer or technical mortar is required.

Who must bear the financial cost of the slab levelling layer?

The levelling layer constitutes a specific smoothing work. If it was not provided for in the screed layer's initial quote because theoretical allowance plans allowed passage without crossing, this service is the subject of an addendum order. Site management then arbitrates the financial burden, which is most often charged to the technical trades responsible for non-compliance with the planned allowances or to the client depending on the contract concluded.

Can loose thermal insulation be used to fill the space between crossed pipes?

The use of unbound loose aggregates is strongly discouraged under a floating screed subject to strict acoustic and mechanical requirements. Loose aggregates risk sliding, settling under site vibrations and creating uneven rigid bridges. A cement-bound lightweight embedding mortar or a stable grout should be used, guaranteeing perfect blocking of the conduits and an incompressible seating for the superimposed insulation boards.

Texts and standards cited

  • SIA 251Screeds in buildings - Specifications for execution and minimum thicknesses

In the same section