Key takeaways
- A heated cement screed requires systematic division as soon as it exceeds 40 square metres.
- The ratio between the length and width of a poured field must never exceed two.
- Any L-shaped layout or doorway strictly requires a clear, through-going division joint.
- The SIA 251 standard prescribes precise joint layout planning before embedding the heating pipes.
Why a 65-square-metre heated screed without a joint leads to failure
On contemporary residential construction sites, the architectural temptation of continuous flooring frequently leads to the elimination of visual separations in living areas. Pouring a 65-square-metre kitchen-living room in a single piece over underfloor heating is the classic mistake that destroys the structure. Under the effect of thermal cycles and the initial shrinkage of the binder, the mortar mass undergoes dimensional variations that its tensile strength cannot compensate for. Without a mechanical break, the screed accumulates internal tensile stress that is released abruptly in the form of erratic transverse cracks.
- Division joint
- A groove or compressible profile created in the thickness of the screed to intentionally weaken a section, channel hydraulic drying shrinkage and absorb thermal expansion without structural defects.
The problem becomes critical when laying large-format tiles. While a small module multiplies the flexible joints capable of absorbing a fraction of surface movements, large-format porcelain stoneware forms a rigid, almost undeformable plate. When the underlying cement screed expands under hot water circulating at 35 degrees, and then contracts when the heating is turned off, the shear plane at the adhesive level undergoes excessive tangential stresses. The tile adhesive fails, the tiles tent up or snap cleanly along the spontaneous fracture line of the screed.
In addition to this thermal expansion phenomenon, differential curling occurs. The edges of a large continuous slab dry and heat asymmetrically compared to the core of the mass. Inertia stresses block the sliding of the floating screed on its thermal or acoustic insulation underlay, causing stress concentrations at protruding corners and in areas of lesser thickness. Regular sectioning remains the only reliable physical safeguard.
The geometric thresholds of the SIA 251 standard and joint execution
The SIA 251 standard strictly regulates the maximum permissible areas for heated floating screeds. The chemical nature of the binder determines the extent of division required. Traditional cement-based mortars exhibit marked hydraulic shrinkage that necessitates reduced sections. Conversely, calcium sulphate-based fluid screeds allow significantly larger single-piece areas, provided the geometry is simple and temperatures are strictly controlled.
| Screed binder type | Maximum area without joint (heated) | Maximum length of one side | Maximum length-to-width ratio |
|---|---|---|---|
| Traditional cement screed (CT) | 40 m² | 8 m | 1:1.5 to 1:2 |
| Calcium sulphate fluid screed (CA) | 200 m² (according to manufacturer's technical data sheet) | 15 to 20 m | 1:2 |
| Shrinkage-compensated cement screed | 60 to 80 m² (with specific admixtures) | 10 m | 1:1.5 |
Beyond the gross area, the ratio between the length and width of the room dictates the occurrence of defects. As soon as a room exceeds a slenderness of 1:2, axial tensile forces surpass the mechanical strength of the material in the longitudinal direction. A corridor or an elongated room measuring 10 metres by 3 must systematically receive one or two transverse joints, even if its total area only reaches 30 square metres. Similarly, rooms with recesses, such as L-, T- or U-shaped areas, must be cut into regular rectangles by joints starting from the interior corners.
- Locating thermal circuitsMark the exact location of pipe penetrations at partition walls and doorways using the heating installer's layout plan.
- Installing uncoupling profilesInstall prefabricated profiles equipped with a compressible thermal expansion foam directly along the thresholds before starting to pull the mortar.
- Executing the shrinkage cutOn cement screeds without a pre-installed profile, make a saw cut with a trowel or angle grinder in the top third of the thickness without ever striking the heating ducts.
- Transmitting the layout planRecord the exact position of the joints on the acceptance report to require the tiler to strictly adopt these lines in their floor layout planning.
The location of the division joint tolerates no approximation during installation. A doorway constitutes an obvious geometric break point that concentrates forces: the joint must align precisely beneath the future door leaf to conceal the junction while isolating two heating zones often regulated by separate thermostats. Any pipe crossing at a joint requires a flexible protective sleeve of at least 30 centimetres to prevent direct shearing of the pipe during slab translation movements.
Cutting a 65 m² heated space: compliance with areas and slenderness ratios
Pouring a heated floating screed over 65 m² in a single piece inevitably exposes the structure to shearing and shrinkage cracking. Under the effect of thermal cycles imposed by the underfloor heating, the mortar undergoes repeated expansions and contractions. Without a break to channel these movements, the floor generates tensile stresses that exceed the mechanical strength of the cement in areas of stress concentration. The resulting failure is transmitted directly to the rigid floor covering, breaking large-format tiles under the effect of horizontal and vertical tensions.
According to the SIA 251 standard, the area of an individual field for a cement-bound floating screed on underfloor heating must not exceed 40 m². As soon as the overall area of a room exceeds this threshold, as in the typical case of an open 65 m² living area, division becomes a mandatory technical requirement. The gross area is not the only determining criterion: the geometry of the field also imposes a strict limitation on the maximum length, set at 8 linear metres, as well as a length-to-width ratio that must not exceed 2:1.
| Geometric parameter | Heated cement screed (CT) | Heated calcium sulphate screed (CA) |
|---|---|---|
| Maximum area per field | 40 m² | Up to 200 m² (according to technical data sheet) |
| Maximum single-piece length | 8.00 m | 15.00 m to 20.00 m |
| Maximum length-to-width ratio | 2 : 1 | 2 : 1 |
| Complex shapes (L, T, U) | Systematic division of recesses | Division of pronounced internal angles |
To treat this 65 m² area, the configuration requires subdivision into two distinct fields, generally balanced around 32 to 33 m² each. In the case of a rectangular room measuring 10 metres by 6.5 metres, an undivided pour results in an unfavourable slenderness and exceeds the 8-metre span. By cutting the bay across its width, two rectangles measuring 5 metres by 6.5 metres are obtained. The length-to-width ratio drops to 1.3:1, perfectly respecting the maximum slenderness criterion prescribed by Swiss professional rules.
Execution of the division joint and transmission of the layout to secondary trades
The mandatory division joint of a heated screed serves a specific function: to allow free shrinkage of the mortar during its initial hardening, and then to absorb the differential expansion movements created by the heating coils. It passes through at least the upper third of the screed, and often half the thickness when sawed, without ever cutting or grazing the embedded underfloor heating pipes. To guarantee flatness and limit the curling effect without breaking horizontal continuity, metal dowels protected by sliding sleeves can be positioned to keep the joint lips at the same level.
- Locating thermal passagesVerify the exact location of the underfloor heating circuits provided by the heating installer. The division joint must never cut an active coil, with the strict exception of flow-and-return supply connections crossing a threshold protected by a compressible insulating sleeve of at least 300 mm in length.
- Inserting the profile or saw cutPlace a specific compressible profile during screed pulling, or make a saw cut using an angle grinder equipped with a depth guide within 24 to 48 hours following the pour for a cement screed, at a depth between one third and half of the total thickness.
- Drawing up the layout recordDraw up a precise dimensioned plan of the expansion and division joints executed in the screed. This document must be transmitted to the site management and recorded in the building file for the tiler.
The screed layer's responsibility extends to the rigorous communication of their joints' position. Large-format tiling bridged over an unnotified division joint will suffer debonding or a clean crack at the very first heating-up of the heating installation. The tiler has a technical obligation to accurately adopt the screed joint alignment in their own installation scheme, using suitable flexible profiles. If the division layout has not been defined by the engineer or architect before the pour, the screed foreman must report the omission and have their layout approved in writing.
Managing defects: erratic cracking and repair protocol
When a heated fluid or traditional screed of 65 square metres has been poured in a single piece without division, thermal expansion and hydraulic shrinkage generate tensile stresses that inevitably exceed the mechanical strength of the mortar. If the failure occurs before tile installation, erratic through-cracks appear on the surface, often starting at internal corners or in the centre of the thermal field. The screed contractor must immediately record the situation in the site log and formally notify the site management in accordance with SIA 118. Pouring a surface levelling compound or masking the crack without structural treatment is out of the question: differential movement will resume as soon as winter heating is turned back on.
- Thermal shutdown and pipe locationHeating must be completely interrupted to bring the floor back to a stable ambient temperature. The exact layout of the heating pipes is recorded using a thermal imaging camera or the heating installer's as-built plans to prevent any accidental drilling.
- Mechanical creation of the omitted jointThe field is divided by mechanical diamond-disc sawing to a depth of at least one third of the screed thickness, complying with the surface limits and length-to-width ratio set by the rules of the art.
- Stitching residual secondary cracksNon-rectilinear cracks located outside the new joint layout are bevelled out, cleaned with industrial vacuum dust extraction, stitched transversely with corrugated metal bars every 25 centimetres, and then filled by injecting a two-component epoxy resin sanded to refusal.
If the large-format tiling is already installed and begins to sound hollow, tent up or shear, removing the damaged tiles is unavoidable. The screed layer, tiler and site management must coordinate the exact alignment of the future expansion joint in the covering with the corrected division plan of the screed, otherwise the defect will recur.
Frequently asked questions
Can a 65 m² heated screed without a joint be kept without sawing if no cracks appear after drying?
No. Even if initial shrinkage has not caused visible rupture, putting the thermal network into operation generates continuous cycles of expansion and contraction. Without a division joint complying with SIA 251, the accumulated mechanical stresses will eventually fracture the screed or debond the rigid bonded covering during the first intense heating season. Retroactive cutting by sawing remains essential.
Who bears the cost of repairs when large-format tiles crack on an undivided screed?
Liability is assessed according to the rules of SIA 118. If the underfloor heating was embedded without a joint layout plan provided by the site management, the screed layer incurs technical liability if they failed to issue a written warning. However, the tiler also incurs liability if they glued their covering without checking for the existence of mandatory division joints.
Can an uncoupling mat be used to compensate for the absence of a division joint?
The uncoupling mat compensates for certain moderate horizontal movements, but it does not replace a division joint over a continuous 65-metre span. Under the effect of extreme thermal stresses, the overall thrust of the floor will exceed the membrane's deformation capacity. Sawing the screed and mirroring the joint through the tiling assembly remain mandatory.
At what depth should an existing screed be sawed to create the joint without piercing the coils?
Sawing must reach one third of the nominal screed thickness without ever touching the minimum pipe embedment. If the total thickness is 65 millimetres with a top cover of 30 millimetres, the saw cut must not exceed 20 millimetres in depth. The use of a micrometric depth stop on the saw and a thermal camera are required.
Texts and standards cited
- norme SIA 251Specifications relating to floating screeds, maximum permissible jointless areas and thermal division criteria.
- norme SIA 118General conditions for the execution of construction work, duties to warn and management of building defects.
