Skip to content
Website
🧱 CFC 281Cement or anhydrite screed: selection and executionChapter 3 of 10 in the section

Liquid screed: formwork sealing, de-aeration, and leaks through pipe penetrations

Pouring a liquid screed tolerates no defects in substrate sealing. This chapter details the transformation of a floor into a perfectly airtight basin prior to pumping in accordance with SIA 251 standard, the inspection of technical penetrations, the crossed de-aeration technique using a smoothing bar, and the organization of the watch station on the floor below to immediately counter any breach.

Key takeaways

  • The fluid consistency turns every floor penetration into a leak point toward the floor below.
  • The perimeter insulation strip with glued apron guarantees the sealing and acoustic insulation required according to SIA 251 standard.
  • Pipe penetrations require sealed waterproof collars installed before laying the film.
  • Cross-pass de-aeration evens out the surface and releases trapped air introduced during mechanical pumping.

Transforming the floor into a sealed basin: systematic caulking of edges and penetrations

A fluid screed, whether calcium sulfate- or cement-based, behaves during the first hours like a heavy liquid subjected to continuous hydrostatic load. Unlike a traditional rule-finished screed that forgives minor substrate discontinuities, self-levelling mortar infiltrates the slightest gap as soon as the lance is opened. The primary objective of preparation is therefore to create a perfectly closed basin across the entire level.

The sliding layer or thermal and acoustic insulation layer must form a continuous and watertight support against cement slurries or fluid mortars to prevent any penetration of liquid material into the load-bearing structure or adjacent walls.

norme SIA 251

Installing the perimeter strip constitutes the first line of defence. On Swiss construction sites, the use of polyethylene foam strips at least eight millimetres thick with an integrated apron or skirt is standard practice. This apron must be carefully folded down over the insulation layer or polyethylene separation film, then continuously glued using an adhesive at least fifty millimetres wide. Direct hot bonding or reinforced tape resists the pressure of the mortar and prevents any lifting of the apron under the weight of the pour.

Vertical penetrations constitute the most vulnerable areas of the foundation slab or floor slab. Sanitary drop stacks, wastewater pipes and electrical sleeves crossing the slab must be treated prior to installing the acoustic insulation. A resilient waterproof collar is applied around each pipe, with its base jointed with elastomer mastic or sealed with fast-setting mortar. For multiple conduit bundles, creating a sealed formwork box fixed to the floor prevents the fluid mortar from running down the technical ducts toward the electrical distribution rooms.

Critical sealing points and bridging techniques for fluid screed
Sensitive areaInfiltration riskTechnical sealing solution
Partition and wall bordersAcoustic bridge and flow under insulationResilient strip with waterproof skirt glued with reinforced tape
Penetration of drainage stacksDirect leak through core drilling into the underlying floorResilient collar sealed with mastic or dedicated formwork
Overlap of PE film sheetsInfiltration of mixing water into the insulationMinimum 100 mm overlap closed with continuous adhesive tape
Exterior threshold passagesMaterial loss toward corridors or stairwellsSealed mechanical stop barrier with support gasket

Cross de-aeration, flatness guidance and rescue organization in case of a leak

Once the basin sealing is secured and the levelling tripods are set with a rotating laser level, pumping can begin. Obtaining a flat and dense surface requires coordinated mechanical intervention as work progresses: passing the levelling bar and the de-aeration broom. These tools break the surface tension of the mortar and evacuate trapped air introduced by mixing or the delivery pipe.

Tamping bar (de-aerator)
Lightweight metal tool mounted on an articulated handle, equipped with one or two cylindrical profiles, used to vigorously agitate the fluid screed over its entire height to drive out air and ensure perfect levelling.
  1. First pass: deep tampingImmediately after pouring to the height defined by the reference tripods, the operator pushes the tamping bar down to two-thirds of the screed thickness. The movement is energetic, oscillating, perpendicular to the direction of progress of the lance to disperse the aggregates homogeneously.
  2. Second pass: surface de-aerationThe second pass is executed crossed at 90 degrees to the first, on the surface only. By regular and lighter sweeping, the de-aerator eliminates air bubbles that have risen to the air-screed interface and smooths the surface film to meet the flatness tolerances of SIA 251 standard.
  3. Extraction of levelling tripodsThe adjustable tripods are removed as finishing progresses. The footprint left by the metal feet closes instantly with a simple surface tap of the fluid mortar.

The organization of a pouring crew is not limited to workers handling the lance and smoothing bar. On any multi-storey construction site, the presence of a watchman on the floor below is mandatory from the start of the pump. Equipped with an inspection lamp, a means of direct communication with the site foreman and emergency patching equipment, this operator constantly checks slab undersides, pipe penetrations and sleeves.

Threshold connections, ducts and technical sleeves: securing the basin before pumping

The fluidity of a self-levelling mortar based on calcium sulfate or cement binder turns every slab gap into a gravity siphon. In accordance with the principles of SIA 251 standard for floating screeds, the entire thermal or acoustic insulation assembly must constitute a sealed and continuous basin before starting the screed pump. Vertical penetrations of sanitary drop stacks, bundles of electrical tubes in corrugated conduits and door frame returns represent the most critical fracture zones on the construction site.

The treatment of pipe passages tolerates no makeshift caulking using scraps of insulation wedged by hand. Technical ducts crossing the raw slab must be encircled with compressed resilient foam collars, secured to the polyethylene separation sheet using butyl adhesives or high-tack fabric tapes. When manifold or distribution stack recesses were not plugged during the structural work phase, the screed layer must stop installation and set up a rigid watertight barrier at the base of the element, mechanically sealed and jointed with elastomer mastic to prevent the liquid from seeping around the pipes.

Materials and caulking methods for singular points
Singular pointSite vigilance pointSelected caulking technique
Edge along glazed bays and French doorsPush of fluid material under the frame or low railEdge strip with polyurethane-glued apron under the frame, reinforced with a sealing gasket under the stop profile
Corrugated conduits and electrical bundles on the floorPeeling of the polyethylene sheet creating infiltration under the layerPrior setting by levelling screed or systematic bridging of conduits under a rigid profile then adhesive waterproof bridging
Metal door frame bases and tubular profilesInternal flow descending directly into the slab thicknessInternal plugging of the base of the upright with dry mortar or high-density trimmed polyurethane foam, then external taping
Pour stop thresholds and movement jointsLifting of the stop board under the pressure of the screedSquared timber or joist mechanically fixed into the slab with a compressed gasket under the baseplate and a waterproof perimeter upturn

Rheological control of paste, passage of bars and neutralization of a sub-floor leak

The success of the pour depends on the fluidity of the mortar delivered by truck mixer or mixed in a mobile plant. Upon truck arrival, the team leader performs a spread test on a flat, clean and moistened test plate. Excessive spread indicates water overdosing which promotes aggregate sedimentation, creates a fragile surface slurry and multiplies the risk of leakage through the slightest microscopic gap. Conversely, excessive viscosity blocks spontaneous levelling and complicates the de-aeration operation.

  1. Levelling and continuous gauge controlDistribute tripods set to laser level across the entire room. Guide the pouring lance as close to the floor as possible to limit splashing against perimeter strips and maintain steady progress without prolonged local stagnation.
  2. First deep de-aerationVigorously pass the tubular de-aeration bar in crossed passes as soon as the surface is covered. The submerged undulation movement releases trapped air bubbles around the underfloor heating pipes and equalizes the paste height.
  3. Smoothing and surface finishingPerform a second very light surface pass using a de-aeration broom or a thin bar. This action breaks the surface tension of the slurry, perfects the flatness required by SIA 251 standard and closes passage marks.
  4. Active monitoring of slab undersidesAssign a worker to continuous inspection of the lower floor throughout the pouring phase. Immediate detection of a droplet or seepage along a sleeve allows pumping to be interrupted before disaster strikes.

The leak incident carries heavy consequences for the company according to the Code of Obligations when the screed soils ceiling insulation, ventilation ducts or technical installations already installed on the lower level. Sub-slab cleaning work must be carried out without waiting for the binder to set: abundant rinsing with clean water of raw surfaces or manual scraping before complete hardening. Rigorous planning in accordance with the ordinance on construction work includes secure access to underlying premises and the disposal of pasty residues in accordance with cantonal environmental directives.

Crisis management: basin rupture and leak toward the lower floor

The loss of watertightness under a self-levelling liquid screed constitutes a major operational emergency. The fluidity of the mortar leads to rapid draining through the slightest breach in a technical sleeve, a poorly glued edge joint or a slab penetration. As soon as a witness reports flow on the underside, the pump operator stops pumping. Every minute of additional injection increases the mass of grout on the ceilings, wiring or insulation of the floor below.

  1. Stopping the pour and alertImmediately stop the batching plant or mixing pump. Cut the electrical power supplies to the flooded sector on the lower level to rule out any risk of short-circuit with the wet mortar.
  2. Emergency caulking under the slabIntervene from below to plug the hole from which the mortar is escaping, using compressed rags, fast-setting expanding foam or a plug of masonry mortar pressed under a panel shored up.
  3. Mechanical evacuation of lost pasteScrape and vacuum up the grout spilled on the lower floor before setting begins. Affected technical components must be washed with clean water before the binder hardens.
  4. Height control and levellingRetake levels with the tripod on the sagging area. Re-inject mortar manually to regain the nominal thickness required by SIA 251 standard, then pass the de-aeration broom again.

Once the surface has stabilized, the team leader logs the incident in the construction site report. Inspection of surface levels verifies that overall flatness remains compliant with SIA 251 standard requirements, thus avoiding costly planning or grinding after complete hardening.

Frequently asked questions

How to spot a sub-screed leak before it penetrates the ceiling?

On a fluid screed construction site, an assistant must monitor the lower floor from the start of the pour. Technical inspection hatches, vertical sanitary shafts and distribution openings constitute critical points to be inspected continuously with a flashlight. At the slightest dripping sound or seepage against a PVC pipe, the stop signal is transmitted by radio to the pump operator to limit the quantity discharged outside the sealed area.

Can a liquid screed be poured directly onto a simple polyethylene film?

Yes, but this film must constitute a truly watertight basin. Polyethylene sheets must have a continuous overlap sealed with waterproof adhesive tape. At the edge, the apron integral with the compressible perimeter strip must be folded down and glued onto the film or acoustic insulation. Without this perfect continuity, the fluid mortar slips by suction under the vapour barrier, lifts the thermal insulation and leaks toward the lower floors.

What is the impact of a leak on the final flatness of a fluid screed?

A local leak creates a visible sagging basin around the rupture. If the grout continues to escape while the rest of the room begins its rheological setting, the depression can no longer be compensated by self-levelling. The screed layer must stop the breach, resupply the area with fresh mortar and immediately pass the smoothing bar again to respect the surface tolerances prescribed by SIA 251 standard.

When should de-aeration be performed after passing the fluid mortar?

Passing the broom de-aerator is carried out as soon as the height is set by the tripods on a poured area, while the paste remains perfectly workable. Two crossed passes at right angles are performed. This movement releases the air trapped during mixing or pumping, homogenizes the surface and activates the surface tension of the binder. Any late de-aeration on a stiffening paste creates indelible permanent waves.

Texts and standards cited

  • SIA 251Floating screeds, foundation slabs and mineral-based cast floor coverings

In the same section