Key takeaways
- The geometric narrowing of the screed in the opening creates a systematic crack starter due to shrinkage.
- Standard SIA 251 requires a full transverse movement joint under each door leaf.
- Heating pipes crossing the passage must be fitted with flexible sleeves at least thirty centimetres long.
- The screed layer records the axis of the joint on the plan to enforce its rigorous alignment by the tiler/flooring installer.
The mechanics of section reduction: why the opening cracks without a joint
During the drying of a floating screed, the mortar undergoes inevitable hydraulic shrinkage due to the evaporation of excess water. This phenomenon generates internal tensile stresses within the mass. In a rectangular room with no obstacles, the screed shrinks uniformly towards its centre of gravity without encountering asymmetrical opposition. On the other hand, when a screed connects two rooms through a door opening without interruption, the geometry of the casting plane changes abruptly. Moving from a wide room section to a constriction of eighty or ninety centimetres concentrates all the mechanical stretching stresses. The narrowest section exhibits the lowest overall resistance to the tensile forces exerted by the two adjacent surfaces, each pulling towards its own barycentre.
- Movement joint
- Straight cut or profile inserted into the thickness of the screed to create a line of least resistance, guiding dimensional shrinkage and preventing erratic cracking during hardening.
Standard SIA 251 classifies these geometric singularities as areas of maximum stress requiring systematic preventive cutting. As soon as a section reduction occurs or a room communicates with another via a doorway, creating a movement joint becomes mandatory to divide the tension fields. Without this clear-cut joint at the opening, the energy accumulated during drying and then during the first heating cycle is released abruptly, shearing the mortar. If the underfloor heating operates with different setpoints between adjacent rooms, a thermal gradient accentuates this movement. This differential places heavy demands on the constriction point and causes transverse failure of the screed.
Execution of the threshold joint and transmission of reference points to the finishing work
- Definition of the axis under the door leafMark the location of the future closed leaf with the site management. The axis of the screed joint must coincide with the door panel so that the separation in the flooring remains invisible from either side.
- Installation of sleeves on heating pipesInstall flexible corrugated ducts on each heating pipe crossing the opening. The protection must cover at least thirty centimetres, i.e., fifteen centimetres on each side of the joint line.
- Installation of the profile or sawing of the movement jointInstall a rigid profile before pouring or mechanically saw the hardened screed to a third of its thickness using a vacuum-connected grinder, taking care not to strike the pipe sleeves.
- Transfer to the setting-out planTake the dimensions of the threshold joint and record them on the execution plan handed over to the client, formally fixing the work before the arrival of the tiler or parquet layer.
The choice of method depends closely on the nature of the mineral binder used. For a traditional cement screed, mechanical sawing takes place as soon as setting allows a clean cut without chipping the edges of the cut, generally between twenty-four and forty-eight hours after screeding. On self-levelling anhydrite flowing screed, the prior installation of a rigid self-supporting profile before pouring avoids any dust generation and guarantees the perfect verticality of the fracture plane. In all scenarios, the cut must reach both door frames without interruption and cross the peripheral edge strip without creating the slightest rigid bridge with the door frame feet or the masonry.
| Technical parameter | Screed on underfloor heating | Insulated floating screed |
|---|---|---|
| Type of cut | Compressible profile or clean-cut movement joint | Sawed cut or dry prefabricated profile |
| Depth of notch | Sawing on upper third without touching the pipes | Sawing on one third to half of the thickness |
| Pipe protection | Mandatory corrugated sleeves over at least 30 cm | Not applicable (without heating network) |
| Cover continuation | Strict vertical continuation in the bonded covering | Recommended aligned continuation depending on the covering |
The screed layer's responsibility ends with the delivery of the screed and the handover of a substrate free from parasitic stresses. The decorative treatment of the surface joint belongs exclusively to the finishing trades. According to standard SIA 251, the tiler and parquet layer have the strict obligation to continue the screed joint directly above its layout in their own installation system, using an elastomer sealant or a suitable profile. Bridging this joint to preserve the visual continuity of tiling inevitably leads to tile cracking or wood detachment. The transmission of the matching layout plan protects the screed layer against any subsequent claims.
Passing the pipe coils under the threshold and protecting the connections
The section reduction at a doorway opening concentrates not only hydraulic shrinkage tensions, but also differential expansion stresses when two rooms are regulated independently. Standard SIA 251 prescribes the execution of a systematic movement joint at the transition between two distinct heating zones or at each narrow passage between two rooms. When the screed encases an underfloor heating network installed by the heating engineer, the implementation of this joint requires strict measures to prevent mechanical shearing of the tubes under the effect of horizontal movements of the two encasing slabs.
To ensure the durability of the system, the flow and return pipes serving the adjacent room must cross the joint profile perpendicularly. The screed layer verifies that each conduit is fitted into a corrugated protective sleeve or closed-cell polyethylene foam sleeve with a minimum thickness of 5 mm. This sleeve must extend over a sufficient length on both sides of the separation profile to neutralise any local locking of the material during heating-up phases.
The movement profile used in the opening generally consists of a rigid polyvinyl chloride or light metal angle fitted with a deformable upper elastomer lip and a perforated base. Cutouts at the base of the profile to let the sleeves pass must be made to measure, without compressing the protective sleeve, to ensure that the cement screed or anhydrite flowing screed maintains its nominal encasing thickness above the heating assembly.
Coordination with floor coverings and alignment management
The effectiveness of a threshold movement joint depends on its precise geometric positioning under the future door leaf. According to Swiss finishing trade best practices, the screed joint must be located directly below the closed door leaf, concealed by the closed door panel. Any deviation of more than a few centimetres makes the joint visible from one of the rooms or creates a non-bonded mortar strip subjected to edge loading when users walk over it.
| Planned final covering | Threshold joint continuation constraint | Consequence of a failure to transfer the joint |
|---|---|---|
| Bonded porcelain stoneware tiles | Mandatory continuation of the screed joint by a flexible joint in the ceramics along the exact same line. | Straight cracking or detachment of tiles laid across the opening. |
| Full-bond parquet | Continuation of the movement joint by a movement profile or elastic cut. | Edge lifting, adhesive shearing or detachment of the wood board. |
| Floating parquet | Decoupling by a joint cover profile at the threshold mandatory to manage peripheral play. | Blocking of the overall expansion of the parquet, warping of the boards in the room. |
| Self-levelling resin flooring | Continuation by sawing and bridging with reinforced polyurethane sealant or specific profile. | Through-crack of the resin film under the effect of screed shrinkage. |
The formal transmission of the layout record between the screed layer and the site management conditions the subsequent interventions of tilers and parquet layers. This document records the location of each cut in the secondary structural work. In accordance with the guidelines of standard SIA 251, the site manager must coordinate the installation plans of the finishing trades with these pre-established fracture lines. A rigid bonded covering that blindly crosses an opening without dividing its own tiling pattern will experience the same stresses as the unjointed screed.
In the presence of pocket sliding doors or full-height glass sliding doors, layout planning must incorporate the position of recessed tracks and floor stops. The interruption of the screed must not weaken the mechanical fixing of these technical elements. Plan coordination between the interior joinery installer and the screed layer prevents drilling dowels into expansion sleeves or accidentally severing a heating pipe when fixing threshold hardware.
Cracking in the opening without a joint: diagnosis, remediation and responsibilities
Omitting a profile at a doorway inevitably leads to erratic mortar failure under the effect of hydraulic shrinkage or thermal expansions. Section reduction at the threshold concentrates mechanical stresses at the exact spot where the screed mass is reduced. When a crack crosses the opening before finishes are installed, the screed layer cannot simply mask the defect with a superficial smoothing compound. Standard SIA 251 reiterates the mandatory nature of the movement joint between two distinct rooms or in the presence of a marked geometric variation.
- Locating heating pipesLocate the exact path of the underfloor heating pipes using a thermal detector or from as-built plans before any mechanical intervention in the passage.
- Cutting and stitching the lipOpen the crack with a grinder equipped with a diamond disc to a third of the thickness. Make perpendicular grooved cuts every twenty centimetres to insert corrugated metal staples.
- Resin pouring and joint creationCarefully vacuum residual dust, inject a two-component epoxy resin and broadcast with quartz sand to refusal. If the two zones heat independently, recreate a clean movement joint down to the insulation by straight sawing.
The screed layer's responsibility ends with the delivery of a flat, stable substrate equipped with joints positioned in accordance with the designer's plans. Once the cut has been established in the screed, the continuation of the joint in the covering falls exclusively within the scope of the finishing trades, whether tiler or parquet layer. If the site management has validated a continuous screed despite the contractor's written warnings, the repair of resulting defects cannot be attributed to the floating screed applicator.
Frequently asked questions
Can a continuous screed be poured under a door if both rooms have the same flooring?
No. Even with uniform flooring, the doorway constitutes a section reduction at the threshold that experiences high tensile stresses during hardening. Standard SIA 251 prescribes a mandatory joint across the opening to decouple the surfaces. Without this physical separation, the slab tears transversely. The bonded covering must then strictly respect this cut to prevent the tiling or resin from splitting.
Where exactly should the screed joint be positioned within the thickness of the opening?
The joint must be located precisely below the future closed door panel, set back from the internal rebate or under the central axis depending on the door frame type. This alignment ensures that the finishing profile or the flexible joint of the covering remains invisible once the door is closed, from either of the adjacent rooms. This layout requires rigorous coordination with the interior joinery plans.
How should a crack appearing at the threshold before tiling be treated?
The thermal regime must first be analysed. If the rooms share the same manifold without differential stress, the crack is stitched with epoxy resin reinforced with metal tie bars. If two distinct heating circuits coexist, the crack is recut with an angle grinder to form a clean through-joint. The finishing tiler must then mirror their surface expansion joint exactly on this line.
Who is responsible if the tiles break at the door threshold?
The screed layer is responsible for the positioning of the screed joint provided for in the execution plans and best practices. If the joint was correctly executed but the tiler covered it with a rigid adhesive or a continuous tile without a flexible movement joint, the defect falls under the tiler's responsibility. Continuing the joint in the covering is a service specific to the finishing trades.
Texts and standards cited
- SIA 251Floating screeds, layout planning and execution of movement joints
