Skip to content
Website
🧱 CFC 281Movement joints and layoutChapter 2 of 10 in the section

Building joints: reproduce identically, across the entire thickness and into the finish

This chapter sets out the mandatory rules for setting out and positioning the floating screed in line with a structural expansion joint. You will learn how to locate the structural axis, install joint profiles that penetrate the entire insulation and mortar assembly, and organise the transfer of information to the finishing trades.

Key takeaways

  • SIA 251 prescribes the strict continuation of structural joints along the exact vertical plumb line.
  • Covering a structural joint causes an irregular diagonal crack right through the mortar.
  • The separation profile must run through the entire thickness of the screed and sound insulation.
  • The exact alignment of the joint must be recorded so that it can be faithfully reproduced in the final finish.

Why bridging an expansion joint leads to the immediate failure of the screed

On a construction site, the movements of the load-bearing structure never stop. Reinforced concrete slabs undergo residual shrinkage, thermal variations and differential deflections between the various building blocks. The structural joint, created by masonry and reinforced concrete trades, provides a mechanical break calculated to absorb these movements without structural damage. When the screed layer steps in, the temptation to pour the screed continuously over this technical gap to save time or simplify insulation installation constitutes a serious defect.

The floating screed has a mechanical strength much lower than that of the load-bearing elements. As soon as the two building blocks move relative to each other, the screed is subjected to shear and pure tensile stresses that it cannot absorb. The result is mathematical: the mortar tears in an uncontrolled manner. This cracking almost never follows a straight line. It runs obliquely, diagonally, forming offset lips that will immediately spall the entire floor assembly under the effect of construction traffic or normal operation of the building.

Building expansion joints must be continued in the screed exactly along their plumb line, with a width at least equivalent and over the entire height of the assembly.

Norme SIA 251

SIA 251 tolerates no compromise on this principle. A settlement or thermal expansion joint of the frame must divide the screed into two entirely independent slabs. No rigid bridge, no hardened mortar residue, no rigid waterproofing membrane must create a rigid connection across this movement slot. Ignoring this transfer exposes the company to complete remedial work at the screed installer's expense, including demolition of the damaged area and complete rebuilding of the substrate.

Installation of the penetrating profile and coordination with the finishing trade

Setting out begins with the precise marking of the structural joint axis before the thermal or acoustic insulation is laid. This reference mark must be projected onto the perimeter walls using a chalk line or laser level. The resilient edge strip and the insulation layers under the screed are cut cleanly along this alignment. No insulation board must overlap the expansion joint of the load-bearing slab, otherwise it will block the planned deformation or tear under the differential pressure of the supports.

  1. Geometric transfer to vertical wallsUse a laser to trace the central axis and edges of the existing structural joint at the base of raw walls to maintain a visual reference after the insulation is installed.
  2. Sectioned installation of acoustic and thermal insulationCut the insulation boards in line with the structural gap, ensuring that no cutting waste falls to the bottom of the structural joint.
  3. Installation of the compressible separation profileInstall an expandable profile or a double metal screed with an elastomer core that rises from the load-bearing substrate to the upper level of the finished screed.
  4. Pouring and careful compaction of the mortar edgesLevel the screed on either side of the profile, ensuring perfect compaction of the mortar against the sides of the flexible seal without deviating from the vertical axis.
  5. Levelling and marking for the subsequent tradeClean the upper edge of the profile and formally record its exact location in the execution report sent to site management.
Execution criteria according to the nature of structural movement
Type of structural movementRequirement for the resilient layerDevice in the screedTransfer to the finish
Pure thermal expansionContinuous interruption with flexible stripMetal profile with elastomer coreAligned joint cover or flexible profile
Differential settlementTotal break without mechanical continuityDouble independent uncoupled profileMechanical profile for three-dimensional movements
Concreting shrinkageStrict alignment on the jointCompressible fractioning profileIdentical transfer into tiles or parquet

The screed layer's work does not stop at compacting the mortar. The full thickness penetration requires a clear transfer to the contractors responsible for the finished floor, whether bonded ceramic tiles or parquet laid on an underlay. The screed expansion joint must be extended vertically through the adhesive and the decorative material. Any attempt to offset the visible joint from the screed axis or to bridge the break with a bonded tile inevitably leads to the tearing or shearing of the finishing elements during the building's first climatic cycles.

Strict vertical transfer: plumbing guidance from the load-bearing slab

Covering a structural expansion joint with screed mortar is a major technical error. The three-dimensional movements of differential settlement, thermal shrinkage and expansion of the reinforced concrete cannot be restrained by a floating screed a few centimetres thick. When the underlying structural joint works, shear and tensile stresses concentrate directly within the unbonded mortar thickness. The material invariably breaks along an irregular diagonal line, generating gaping spalls and irreversible level differences. SIA 251 prescribes interrupting the screed work over its entire thickness to exactly reproduce the layout of the structural division.

The geometric transfer must be carried out before laying the thermal or acoustic insulation layers. Upon handover of the raw substrate, the team leader marks the exact axis of the structural gap on the adjacent vertical walls using a chalk line or a locked laser reference. This reference line will serve as a permanent guide during pouring. Attempting to guess the position of the structural slot after rolling out an acoustic felt or insulation boards almost always leads to an offset of a few centimetres. Even a minor offset creates a cantilevered crack initiation point: the screed cracks diagonally between the reinforced concrete lip and the poorly positioned surface profile.

Consequences of the position of the screed joint relative to the structural expansion joint
Execution configurationMechanical behaviour under stressPathology observed on the structureExecution compliance
Strictly continued plumb (axis on axis)Free transfer of horizontal translations and vertical settlementsNo cracks; free play of the screed lipsCompliant according to SIA 251
Lateral offset of 20 to 50 mmShear stress combined with a leverage effect on the underlayOblique cracking joining the structural gap underneathNon-compliant; total repair required
Total continuous covering (blind screed)Full blocking of the building's thermal expansion movementsSpontaneous bursting, diagonal cracking and level differenceCharacterised construction defect

Continuity of the break through the insulation and preparation of the subsequent trade

The physical break must run through the entire floor assembly, from the upper face of the structural concrete to the top surface level of the screed. Thermal or impact sound insulation boards must under no circumstances bridge the building gap. The screed layer cuts the insulation strips and panels cleanly in line with the structural gap. To prevent fluid or traditional mortar from seeping into the underlying gap during compaction or screeding, a rigid stop profile or a closed compressible foam strip is firmly inserted. This watertight barrier guarantees the mechanical independence of the two floating slabs without creating a rigid acoustic bridge.

The screed layer's work ends with the provision of a sound, straight and perfectly vertical edge. Although the installation of definitive metal or elastomer decorative profiles falls to the finishing trades depending on the chosen finish, the screed package must deliver a rebate with flawless tolerances. The width of the gap left in the mortar must match point by point the width of the structural joint, without burrs or residual laitance in the slot. Setting-out data and level surveys are recorded to allow hard or resilient floor installers to extend this discontinuity up to the usable surface without stressing the assembly.

Management of non-conformities and repair of a covered structural joint

Covering a structural expansion joint without transferring it constitutes a major defect. When the screed encases the gap without a penetrating profile, the building's expansion and retraction stresses cause irregular surface cracking, often oblique or branched. According to SIA 251, the structure's building joints must be identically continued, along the exact plumb line and over the complete thickness of the assembly, insulation included.

As soon as the defect or erroneous covering is noted prior to handover, the site manager orders mechanical remedial work. The screed must be sawn over its entire depth, perpendicular to the floor and in precise alignment with the underlying structural joint. If heating pipes cross the area without a sliding sleeve, site management must immediately arbitrate the intervention.

  1. Setting out and mechanical cuttingLocate the exact axis of the structural joint from the perimeter recesses. Cut the screed using a table saw or angle grinder with an attached industrial vacuum cleaner, over the full height down to the resilient material.
  2. Recessing and cleaning out the grooveRemove the degraded screed lips to create an opening matching the profile of the initial joint. Carefully vacuum dust and mineral debris from the bottom of the rebate.
  3. Installation of the penetrating profileInsert an expansion profile adapted to the width of the gap, equipped with perforated wings anchored on either side, or install a compressible flexible strip that completely uncouples the two screed slabs.
  4. Notification for the finishing tradeDraft a formal notice to the tiler or parquet layer to record the axis of the profile. The final finish must scrupulously extend this uncoupling plane up to the usable surface.

The floating screed thus regains its kinematic autonomy. In application of the rules of the trade and the Code of Obligations governing construction defects, remedial costs are borne by the pouring contractor if the engineering firm's joint layout plan was not respected during installation.

Frequently asked questions

Can the screed joint be offset by a few centimetres relative to the slab joint?

No. Any misalignment between the substrate joint and the screed joint is strictly prohibited. The slightest eccentricity subjects the mortar located between the two marks to unsustainable bending and shear stresses. The screed will inevitably fracture on a bevel to join the building's natural movement. The vertical plumb line must be respected to the millimetre over the entire height of the assembly.

How to mark the plumb of the joint during floor insulation installation?

Before installing the insulation boards, trace the axis of the structural joint on the perimeter walls using a laser level or chalk line. Interrupt the acoustic or thermal underlay along the line by inserting a continuous compressible strip. This visual reference mark makes it possible to position the vertical screed profiles exactly above the slab break before pouring.

What to do if an underfloor heating pipe crosses a building expansion joint?

A heating circuit must never cross a structural joint without specific provisions. If the heating engineer's layout requires it, the pipe must cross the axis perpendicularly, protected in a closed flexible sleeve at least thirty centimetres long centred on the joint. This prevents crushing or stretching of the network during dynamic loads on the structure.

What is the screed installer's responsibility regarding the final finish trade?

The screed installer must deliver a clean, vertical joint completely free of rigid bridges formed by cement laitance. They document the location of the profiles in their execution report. The tile or parquet layer is required to continue this joint exactly plumb in their wearing course, without covering it with adhesive or continuous rigid elements.

Texts and standards cited

  • SIA 251Floating and bonded screeds inside buildings, fractioning and uncoupling requirements
  • SIA 118General conditions for the execution of construction work and management of non-conformities
  • code des obligationsGeneral rules on the contract for services, contractor obligations and reporting of defects

In the same section