Key takeaways
- An air void beneath the heating coil creates a thermal break that drastically reduces the output.
- The superplasticising additive optimises the compactness of the mortar without requiring excess mixing water.
- Careful compaction using a vibrating screed board or tamping bar guarantees continuous embedding.
- Standard SIA 251 prescribes intimate contact between the screed and the heating pipes.
Thermal break caused by an air void beneath the heating coil
On an underfloor heating system, the floating screed fulfills a dual function: it distributes operating loads and serves as a thermal diffuser starting from the pipes installed by the heating fitter. The energy efficiency of the assembly depends on the quality of the physical contact between the mortar and the pipe network. If the mortar is poured too dry or without sufficient compaction, it creates a thermal shadow bridge beneath the lower generatrix of the pipes. Stagnant air exhibits negligible thermal conductivity compared to dense mortar. An air pocket beneath a pipe insulates the latter from the screed mass, blocking the heat flow directed downwards and to the sides.
- Thermal embedding of the pipe
- The action of completely surrounding the circumference of the heating pipe with screed mortar, without bubbles or discontinuities, in order to transfer the heat energy from the heat-transfer fluid to the floor mass by direct conduction.
When embedding is defective, the overall output of the underfloor heating drops. The heat-transfer fluid must circulate at a higher flow temperature to compensate for the parasitic thermal resistance of the air pockets. This malfunction generates excessive energy consumption and disrupts the responsiveness of the installation. Furthermore, non-embedded areas concentrate abnormal mechanical stresses: the cyclic expansion of the unbelted pipe causes microcracks in the adjacent cement matrix. According to standard SIA 251, the screed must completely surround the heating pipes to form a homogeneous and stable body.
| Embedding configuration | State of contact beneath the pipe | Consequence on conductivity | Mechanical behavior |
|---|---|---|---|
| Complete and compacted embedding | Continuous 360-degree contact | Maximum and homogeneous thermal diffusion | Restrained expansion without cracking |
| Mortar pulled dry without additive | Frequent air voids on the underside | Increased thermal resistance, drop in output | Risk of edge spalling and local detachment |
| Excess water without plasticiser | Bleed water pockets followed by cavities | Loss of inertia and high open porosity | Low compressive strength and bleeding |
Execution: superplasticising additives, consistency and compaction of the mortar
To eliminate air voids beneath the network without compromising the mechanical strength of the mortar, the addition of a superplasticising or plasticising additive is essential on traditional cement screed. This admixture acts by deflocculating the cement grains. It makes it possible to reduce the amount of mixing water while increasing the workability of the mixture. Lowering the water-cement ratio densifies the hardened paste, which improves the thermal conductivity of the screed while reducing hydraulic shrinkage during the drying phase.
For screeds on insulating layers with integrated heating, the mortar must exhibit suitable consistency and compactness guaranteeing complete embedding of the heating elements, without segregation or accumulation of bleed water.
Norme SIA 251
- Precise dosage of the additive in the mixerIntroduce the plasticising admixture directly into the mixing water or according to the manufacturer's instructions. Strictly observe the prescribed proportions to prevent any setting delay or aggregate segregation in the truck mixer drum.
- Spreading and primary distributionPour the plastic-consistency mortar while avoiding crushing the heating pipes or tearing out the fixing clips. Distribute the mixture uniformly using a shovel or a specific rake above the upper generatrix of the network.
- Mechanical compaction around the heating coilVigorously beat the mortar using a screeder's vibrating bar or flat tamper to force the paste to flow beneath the pipes. Compacting must drive out trapped air until laitance rises uniformly around each pipe.
- Levelling and surface closingPull the screed using an aluminium screed board supported by the level guides. Complete with careful floating and smoothing to close the surface porosity without separating the mortar already compacted around the pipes.
Thermal output and mechanical stability according to standard SIA 251
The cement matrix of a floating screed does not merely serve as a mechanical load-distribution layer; in a heated floor assembly, it acts as the main heating body of the room. Standard SIA 251 requires rigorous mortar compactness to guarantee both complete embedding of the pipes and the heat transmission planned by the thermal design. When the mortar exhibits excessive viscosity during pouring, an arching effect systematically forms above or below the pipe bends. The paste does not flow beneath the lower generatrix of the coils, leaving a continuous air pocket along the network. This structural defect impairs the entire energy balance of the floor.
Stagnant air possesses one of the highest thermal resistances of common building materials. A localised air pocket beneath the pipe acts exactly like an unwanted insulating cut. While the heat-transfer fluid must dissipate its calories radially across 360 degrees of the pipe circumference, the lower half of the pipe finds itself thermally decoupled from the screed. To compensate for this lack of exchange and reach the setpoint temperature in the living space, the generator must deliver water at a higher temperature. This malfunction degrades the coefficient of performance of the installation, causes asymmetrical temperature gradients in the plastic sheath of the pipe and increases the overall inertia of the system.
| Evaluation criterion | Mortar without plasticiser (voids beneath pipe) | Additived and compacted mortar (total embedding) |
|---|---|---|
| Circumferential contact of the pipe | Partial (50 to 70%), hollow pockets beneath the network | Integral (100%), perfect embedding of the periphery |
| Overall thermal conductivity | Locally degraded by reverse thermal bridge | Homogeneous, compliant with thermal calculation values |
| Flexural strength of the screed slab | Weakened by crack initiation points along the voids | Optimal according to the prescribed strength class |
| Mechanical behavior under rolling load | Risk of sagging or shearing at the void | Continuous transmission of forces towards the floor insulation |
Beyond the heat loss, voids beneath pipes represent a major mechanical weakness for the finished screed. Standard SIA 251 requires the screed to rest uniformly on its resilient support without internal cantilevers. When a concentrated or rolling load travels across the floor, the presence of an air pocket transforms the pipe into a suspended bridge without solid support beneath its base. The section of mortar located above the pipe then works in pure flexion, without the incompressible support of the underlying material. This results in a high risk of longitudinal microcracking along the pipe routes, which can propagate right through to the wear surface and crack the future hard floor covering.
Diagnosis of embedding voids and behavior during initial heating
Preparatory heating according to the protocol of standard SIA 251 constitutes the revealing step of the embedding quality achieved by the screed layer. This gradual thermal rise phase does not merely validate the drying and the absence of hydraulic binder shrinkage stresses: it subjects the embedding to a real differential expansion test. If the mortar is riddled with air cavities beneath the network, the pipe expands freely in the void instead of transferring its energy by direct conduction. This heterogeneity generates shear stresses at the residual contact points between the plastic and the hardened mortar.
- Acoustic auscultation prior to the sounding hammerThe foreman sweeps the surface with a sounding hammer or steel ball before initial heating. Hollow-sounding areas aligned with the theoretical layout of the coils reveal an embedding defect or outright detachment between the screed and the generatrix of the pipes.
- Thermographic survey at the start of the first temperature plateauAs soon as temperate water is injected into the circuit, the operator observes the floor using a thermal camera. A correctly embedded pipe produces broad and continuous heat diffusion in the shape of a diffuse sheet. A poorly embedded area shows highly localized hot spots followed by abrupt radiation interruptions.
- Visual inspection of expansion joints and sleevesChecking expansion joint crossings where protective sleeves and pipes intersect. These critical areas often accumulate shortages of mortar due to geometric congestion and require redoubled manual compaction.
The integrity of the embedding governs the acceptance of the work and the authorisation for laying subsequent coverings. The initial heating protocol recorded by the screed layer certifies that the mortar has undergone the thermal rise without structural disorder. In the absence of a void beneath the pipe, the screed ensures linear conduction, eliminates the risks of dynamic punching failure points and preserves the performance of the heating installation as guaranteed to the client by best practices.
Corrective measures in the event of embedding defects and voids beneath pipes
When the initial heating protocol reveals abnormal system inertia, continuous cold strips on the floor or rectilinear cracking along the pipes, the embedding defect is proven. The presence of air cavities beneath the pipe forms a parasitic thermal barrier that blocks the diffusion of calories and degrades the mechanical strength of the floating screed. As soon as these anomalies are noted, suspending the heating is mandatory to prevent any failure under the effect of excessive thermal gradients.
- Contradictory diagnosis and thermal mappingConvene the site management and the heating installer to carry out a thermal camera inspection combined with acoustic sounding using a hammer. This non-destructive auscultation accurately delineates unbonded areas and underlying air voids without perforating pressurized pipes.
- Low-pressure injectionFor localized cavities without structural failure, drill millimeter-sized wells between the coils. Then inject a fluid epoxy resin or a mineral micro-grout specially formulated for thermal transfer, under a minimum pressure that guarantees filling without lifting the screed or displacing the conduits.
- Demolition and localised repairIf the mortar exhibits insufficient compactness or extensive gravel pockets due to installation without a plasticiser, cut out the compromised section after precise marking of the circuit. Reconstruct the work using a fluid, shrinkage-compensated mortar, perfectly compacted around the heating pipes.
The resolution of these defects falls within the scope of the contractor's duties under the Code of Obligations and standard SIA 118. All findings, drillings and consolidation operations must be recorded in a site report countersigned by the representative. In accordance with the criteria of standard SIA 251, no new heating plateau must be initiated before the complete hardening of the replacement materials, in order to ensure the essential overall cohesion between the mortar and the heating coil.
Frequently asked questions
How to detect a void beneath a pipe without damaging the heating coil?
Auscultation takes place during initial heating by combining two non-destructive methods. Infrared thermography highlights cold strips along the pipes where air blocks the heat flow. In parallel, meticulous acoustic sounding using a metal rod or a tiler's hammer makes it possible to hear a characteristic hollow sound on poorly embedded areas. This approach avoids any core drilling detrimental to the hydraulic network.
Can water be added on site to improve embedding if the additive is missing?
Adding water without a superplasticising additive is a serious technical error prohibited by standard SIA 251. Excess water causes a direct drop in mechanical compressive and flexural tensile strengths. It induces heavy bleeding, aggregate sedimentation and major hydraulic shrinkage that cracks the screed above the pipes. Only a plasticising or water-reducing admixture guarantees the plasticity required to wet the underside without altering the binder.
What is the consequence of an air void beneath the pipe on energy consumption?
Immobile air possesses poor thermal conductivity, close to that of insulation. When a void separates the pipe from the mortar mass, heat no longer diffuses by conduction but stagnates locally. To compensate for this lack of heat exchange and reach the desired ambient temperature, the heat pump must raise its flow temperature by several degrees. This malfunction leads to permanent excess electricity consumption and significantly degrades the seasonal coefficient of performance of the installation.
How to react if pipes become detached during screed pouring?
If pipes become detached under the pressure of the mortar, pouring must be interrupted immediately on this bay. Pushing the pipe back into the fresh mortar is ineffective because it will rise again under its own elasticity. The team must clear the material, press the conduit against the insulation and install new reinforced anchor clips. Once the stability of the coil is checked, the plasticised mortar is put back in place, then carefully compacted to restore continuous embedding.
Texts and standards cited
- SIA 251Floating screeds inside buildings: requirements for mortars, embedding and tolerances
- SIA 118General conditions for the execution of construction work: notice of defects and contradictory acceptances
