Skip to content
Website
🧱 CFC 281Section 3 of 610 chapters

Screed on underfloor heating and floor covering: the execution reference standard

This section covers the installation of floating screeds on underfloor heating in accordance with SIA 251 standard requirements. Aimed at site managers, foremen and construction managers in CFC 281, it establishes the embedding rules, covering thicknesses depending on the binder, and the mandatory layout of expansion joints. It also details the joint inspection records to be formalised with the heating installer prior to any pouring.

  • 10chapters
  • 22 000words
  • 6sections in the training course
  • 60chapters in total

Key values to remember 5

Norme SIA 251

35 mm

Minimum covering above the pipe for cement screed

Norme SIA 251

30 mm

Minimum covering above the pipe for calcium sulphate screed

Norme SIA 251

40 m²

Maximum surface area of an unjointed field for heated cement screed

Norme SIA 251

8 m

Maximum length of a field without an expansion joint

Industry trade guidelines

6 bar

Standard test pressure maintained in the coil during pouring

Scope of work for the screed layer and trade boundaries

The installation of a screed on underfloor heating places the screed layer at the direct junction between the building's infrastructure, the thermal installations package, and the finishing trades. According to SIA 251 standard, the screed layer's role is to uniformly embed the pipe bundle and form a stable, flat and mechanically resistant thermal mass capable of distributing heat without de-bonding or cracking under the effect of thermal stresses.

  • What the screed layer is responsible for: under-screed insulation, separating membrane, perimeter edge insulation strip, potential incorporation of plasticising or fluidising admixtures, complete embedding of the pipes, thickness adjustment above the pipe crowns, sawing or profiling of control joints, and preparation of the residual moisture test report.
  • What falls under the heating engineer (CFC 241): axle spacing and laying pitch, selection of composite or synthetic pipes, fixing of the pipe coil onto the insulation or mesh, connection to the distribution manifolds, air venting, maintaining hydraulic pressure, and operating the boiler during the initial heating-up phase.
  • What belongs to structural work (CFC 201 and 211.1): flatness and load-bearing capacity of the reinforced concrete floor slab, structural recesses, and the treatment of rough step transitions.
  • What is incumbent upon floor covering installers (CFC 282, 273 and 283): conformity verification of the substrate, checking of the heating-up protocol, selection of the adhesive system, and rigorous compliance with the layout of the screed joints through the tiling or bonded parquet.
Distribution of services between the screed layer and associated trades
Work elementResponsible tradeTechnical reference
Raw slab and airtightnessStructural work (CFC 201 / 211.1)Load-bearing structure standards
Pipes, manifolds and test pressureHeating engineer (CFC 241)Heating industry guidelines
Edge strips, underlay and embeddingScreed layer (CFC 281)SIA 251 standard
Joint crossings via sleevesHeating engineer or screed layer according to tenderSIA 251 standard and specifications
Fractioning and shrinkage jointsScreed layer (CFC 281)SIA 251 standard
Finishing covering and flexible jointsTiler / Parquet layer (CFC 282 / 273)SIA 248 and SIA 253 standards

Execution method and sequence of construction phases

The execution of a heated floating screed requires a strict chronological schedule. Each step governs the mechanical stability of the slab and prevents major defects such as thermal warping, surface pipe shadowing, or bonded tile fracture. The ten chapters of this section detail each critical point, from initial verification through to defect remedial treatment.

  1. Preparatory phase: network inspection and thicknessesValidation of the minimum covering (chapter 1) and the joint inspection record of the pressure gauge with the heating engineer (chapter 2) are mandatory. It must be ensured that the pipe will remain pressed against the bottom and will support the weight of the mortar without floating.
  2. Layout phase: expansion freedom and crossingsA screed exposed to heat expands significantly. It is essential to divide the areas according to the maximum prescribed surfaces (chapter 3), sleeve every pipe crossing a cut (chapter 4), and dimension the perimeter edge strips to prevent wedging (chapter 7).
  3. Embedding phase: workability and special systemsThe mortar must perfectly surround each generatrix of the pipe to eliminate insulating air pockets (chapter 5). In renovation work with low installation height clearance, suitable thin formulas require special care regarding reinforcement and compactness (chapter 6).
  4. Equipping and as-built phase: traceability of the workThe incorporation of the thermal sensor requires a sealed and inspectable protective sleeve (chapter 8). Before encasing the networks, photographic and dimensional records protect the work against subsequent drilling (chapter 9).
  5. Expert assessment and remedial phase: defect treatmentIf tiles debond due to the absence of a thermal joint, stress analysis guides remedial sawing and determines the contractual liabilities for the damage (chapter 10).

📘 Chapters in this section 10

Screed on underfloor heating and floor covering

Cover: minimum according to the binder, and the crack above the pipe

Lock in the thickness above the pipes to prevent the appearance of shadowing and thermal shrinkage cracks.

Screed on underfloor heating and floor covering

Before pouring: pressure pipe, pressure gauge reading and jointly signed joint inspection record

Secure the pouring process by demanding the joint inspection record of the network pressure with the heating engineer.

Screed on underfloor heating and floor covering

A heated screed moves: maximum area per field, slenderness and mandatory joint

Determine the admissible surface areas and slenderness ratios to absorb expansion without breaking the flooring.

Screed on underfloor heating and floor covering

Crossing a joint: protective sleeve on the pipe, and joint left free

Prevent the shearing of hydraulic pipes at fractioning locations using the prescribed flexible sleeves.

Screed on underfloor heating and floor covering

Good embedding: additive, workability, void beneath the pipe and heating output

Optimise heat transfer by eliminating air pockets beneath the network using suitable admixtures.

Screed on underfloor heating and floor covering

Renovation: low-profile system, available height and accepted compromise

Arbitrate recess constraints in renovation projects using thin systems while preserving thermal mass.

Screed on underfloor heating and floor covering

Edges: boundary constraints, compressed edge strip and corner crack

Protect re-entrant corners against crushing by dimensioning the edge strip according to the expansion.

Screed on underfloor heating and floor covering

The sensor in the screed: position, replacement conduit, and marking

Position the sensor's thermowell to guarantee accurate and durable thermal regulation.

Screed on underfloor heating and floor covering

Document before pouring: photo of the heating coil, joint plan and drilling depth

Archive the dimensioned photographic as-built records of the networks to protect the site from subsequent trades perforations.

Screed on underfloor heating and floor covering

Cracked tiles: diagnosis, remedial sawing and unavailability compensation

Identify the mechanical origin of tile cracking and cleanly saw the joint without cutting the element.