Key takeaways
- The temperature rise of a heated screed generates continuous horizontal thrust towards the perimeter walls.
- Standard SIA 251 requires complete decoupling to allow the floating slab to move freely.
- An incompressible edge strip transmits the load to the partition walls and causes the perimeter zones to burst.
- Any non-decoupled re-entrant corner forms a fixed point that immediately initiates a diagonal crack under stress.
Thermal expansion of a heated screed and the thrust exerted on the edges
Under the effect of the temperature increase induced by the underfloor heating circuit, a liquid or traditional screed undergoes continuous dimensional variation. This physical phenomenon corresponds to the coefficient of thermal expansion of the mineral binder, which is generally between 0.010 and 0.012 millimetres per metre and per Kelvin for a cement screed. Over a room length of ten metres subjected to a thermal differential of twenty degrees during operational heating-up, the cumulative linear elongation reaches more than two millimetres. This dimensional increase acts bidirectionally across the entire footprint of the floor.
Floating screeds on thermal or acoustic insulation layers must be separated from vertical construction elements by continuous, compressible edge strips capable of absorbing thermal movements and preventing any acoustic or mechanical bridge.
norme SIA 251
If linear movement is hindered by a rigid edge or accidental contact with the masonry, the expansion energy cannot dissipate freely. The thrust force immediately turns into a major internal compressive stress. A screed blocked at the edges accumulates considerable axial pressure seeking out the weakest point of failure: lifting in the centre of the panel through buckling, crushing of the mortar at the base of the wall, or sudden fracturing during alternating heating and cooling phases.
| Binder type | Average thermal expansion | Residual shrinkage upon initial heating | Edge thrust |
|---|---|---|---|
| Conventional cement screed | 0.012 mm/m/K | Significant hydraulic shrinkage | Moderate (shrinkage and expansion partially offset each other) |
| Calcium sulphate screed (anhydrite) | 0.015 mm/m/K | Virtually zero shrinkage | Very high (pure thermal expansion without compensation) |
Edge strip compressibility and critical treatment of re-entrant corners
Perimeter decoupling relies on an edge strip whose elastic deformation capacity must persist throughout the structure's service life. In accordance with Swiss codes of practice, a polyethylene foam strip of at least eight to ten millimetres nominal thickness is required for heated screeds. The compressibility of the material must guarantee permanent deformation under moderate load without ever forming a hard spot. An overly dense insulation, plaster residue or cement slurry infiltrated behind the strip totally cancels out the required clearance.
Re-entrant corners are the most vulnerable areas of the floating floor. When a wall or partition forms a protruding recess towards the interior of the room, the screed slab tries to wrap around this obstacle during its thermal expansion. If the edge strip is pinched or has insufficient compressed thickness at this location, the edge of the wall acts as a splitting wedge. Transverse tensile stresses concentrate at the tip of the re-entrant corner, inevitably causing an open diagonal crack starting from the corner and extending inwards into the span.
- Continuous installation of the compressible stripMechanically fix or glue the edge strip to all rising vertical walls, columns, service ducts and door frames without any interruption in the layout.
- Safety reinforcement at re-entrant cornersAt re-entrant corners and protruding pillars, double the decoupling thickness or ensure that the strip follows the edge perfectly without being put under tension.
- Watertight connection of the flapRoll out the polyethylene skirt attached to the strip over the floor insulation and carefully tape the joint to prevent any slurry passage.
- Maintaining the strip until tilingProhibit trimming of the edge strip after pouring; it must only be cut at the time of laying the final floor covering by the competent tradesperson.
Prevention of acoustic and mechanical bridges at the building perimeter
During pouring, the fluid or traditional mortar looks for the slightest flaw to work its way behind the perimeter strip. As soon as cement paste or liquid calcium sulphate crosses a strip joint or bypasses a poorly insulated service duct, a hard point forms against the raw masonry or concrete slab. This local blockage turns the natural linear expansion of the floating slab into a point thrust vector directed towards the wall. During the first temperature cycle, the force is no longer distributed along the edge length: stress accumulates at this fixed point until the screed ruptures in the form of bursting or an oblique crack directed towards the centre of the room.
- Continuous installation of the resilient stripUnroll the closed-cell polyethylene foam strip around the perimeter of vertical walls, door frame bases and rising columns. The strip must project above the finished screed level by at least 20 millimetres.
- Treatment of joints and cornersEnsure an overlap of at least 50 millimetres between successive lengths of edge strip. In re-entrant corners, cut only the lower skirt to fold it flat, without ever cutting through the height of the insulation foam.
- Watertight connection with the protective filmFold back the flexible flap onto the thermal or acoustic insulation, then tape the entire joint line using a wide adhesive tape to prevent any passage of fresh mortar beneath the resilient heel.
- Sleeving of penetrations and pipesWrap each vertical pipe or service duct penetration in a closed resilient sleeve of a thickness equivalent to the perimeter strip before placing the mesh or pouring.
Thermal cycling behaviour and control of corner stresses
The progressive heating of the embedding panel generates constant bidirectional thrust. When the room shape features a re-entrant corner, the two longitudinal displacement vectors converge towards the same internal apex. If the compressibility of the perimeter strip is insufficient or if a masonry wall corner restricts the slab's freedom of translation, the material undergoes a concentration of shear stresses. The flexural tensile strength of the cement or anhydrite screed is quickly exceeded, causing a corner crack opening at 45 degrees from the re-entrant edge.
| Geometric configuration | Predominant thermal force | Execution risk factor | Consequence on the screed |
|---|---|---|---|
| Straight right edge | Distributed axial thrust | Edge strip thickness less than 5 mm | Screed lifting at the edge or premature crushing of the foam |
| Re-entrant corner (L or T shape) | Concentrated biaxial shear | Omission of the intersecting crack control joint at the apex | Through diagonal crack starting from the re-entrant corner |
| Column base or isolated post | Divergent radial pressure | Absence of flexible sleeve or screed run | Star-shaped bursting of the screed around the rigid obstacle |
| Doorway or narrowing | Differential tension between zones | Misalignment of the screed joint with the expansion joint | Random transverse crack at the narrowed section |
The initial heating-up protocol required by standard SIA 251 serves as a proof test for the integrity of the structure. During this phase, the screed layer must visually check edge behaviour and the actual compression of the flexible strips. Bulging at a temporary skirting board or an incipient crack in a re-entrant corner signals immediate kinematic blockage. Trimming of the perimeter strips must under no circumstances take place before the complete completion of the thermal cycle and the cooling of the system: cutting the strip too early would allow construction waste, rubble and heavy dust to fill the residual decompression void, creating irreversible rigid bridges beneath future floor coverings.
Management of edge defects and treatment of mechanical blockages
During the first temperature-raising protocol, a fluid or traditional screed over underfloor heating undergoes strong multidirectional thrust. If a rigid obstacle hinders this free movement—mortar run bridging the compressible strip, hardened plaster waste behind the perimeter insulation, or pinched edge strip without clearance—the thermal expansion of a heated screed finds no outlet towards the walls. Compressive stress accumulates along the boundaries and concentrates brutally on the geometric singularities of the room. The characteristic defect remains the re-entrant corner crack, which starts at the apex of the corner and propagates diagonally towards the centre of the room under the combined effects of bending and shear forces, sometimes accompanied by slight edge lifting.
- Mechanical release of the edgeCheck the continuous elasticity of the edge joint along the partitions using a utility knife or scraper. Cut away with an angle grinder fitted with a dust extraction guard all slurry burrs or hard deposits that have filled the decoupling space. It is imperative to restore the compressibility of the edge strip over the entire thickness of the floating screed in accordance with standard SIA 251.
- Diagnosis and monitoring of the layoutTemporarily stop the temperature rise to stabilise the floor at the reached level. Record the exact path of the rupture at the re-entrant corner using a millimetre crack gauge. Confirm the absence of vertical displacement between the edges of the fracture and check that the integrated coils have not undergone any mechanical shear.
- Structural resin stitchingAfter total edge decompression, open up the crack and make perpendicular slots about ten centimetres long every twenty-five centimetres. Insert notched metal staples and then inject a fluid two-component epoxy resin. Sand the surface to rejection with dry quartz prije before resuming the thermal cycle.
Frequently asked questions
Why does a heated screed crack primarily at re-entrant corners?
When a screed heats up, its thermal expansion occurs in two dimensions. At a re-entrant corner, the orthogonal thrust vectors converge and generate an extreme concentration of tensile and shear stresses. Without effective decoupling or the creation of a preventative crack control joint extending the re-entrant edge according to standard SIA 251, the mortar cannot withstand the internal tensions and yields through an open diagonal crack.
What minimum thickness of edge strip must the screed layer install for underfloor heating?
For a heated floating screed, the perimeter strip must have a minimum thickness of eight millimetres, increased to ten millimetres on large spans. The compressibility of the edge strip must allow a deformation of at least five millimetres under the expansion force without transmitting the thrust to the walls. According to standard SIA 251, the foam must be continuous, without interruption at corners, and equipped with a watertight flap folded down onto the insulation.
How can the absence of a mechanical bridge along skirting boards and walls be checked on site?
Before triggering the temperature rise, the site manager carries out a visual and tactile check over the entire perimeter. They verify that the foam protrudes everywhere above the finished level of the screed and that no slurry runs have filled the peripheral space. Manual pressure along the wall confirms the elasticity of the joint. In the event of a hard spot, immediate clearance with a saw or scraper is imperative.
Can tiling be laid on a screed featuring a stabilised corner crack?
The installation of a hard covering can only begin after complete treatment of the fracture and completion of the heating protocol. If the crack appeared following an edge blockage that has now been released, it must be mechanically stapled and keyed to rejection with epoxy resin. The screed layer certifies the stabilisation of the substrate, thus allowing the tiler to apply their decoupling mat or respect the movement joint required by standard SIA 251.
Texts and standards cited
- SIA 251Floating screeds, execution rules, perimeter joints and heating-up
